noctua NH-D9 DX-4677 CPU Cooler Installation Guide

noctua NH-D9 DX-4677 CPU Cooler

Dear customer

Thank you very much for choosing the Noctua NH-D9 DX-4677 4U.
Our DX line of coolers has become a default choice in high-performance quiet cooling solutions for Intel Xeon processors, and I’m confident that you will be able to sense some of the research, attention and care we’ve put into making this product. Enjoy your NH-D9 DX-4677 4U!

Yours sincerely,

This manual will guide you through the installation process of the SecuFirm2™ mounting system step by step. Prior to installing the cooler, please consult the compatibility centre on our website (ncc.noctua.at) and verify that the cooler is fully compatible with your motherboard. Please also make sure that your PC case offers sufficient clearance for the cooler and that there are no compatibility issues with any other components (e.g. tall RAM modules). Double check that the heatsink and fan clips do not make contact with the VGA card, other PCIe cards, motherboard heatsinks or any other components. Noctua cannot be held responsible for any damage or losses caused by compatibility issues. Should you encounter any difficulties, please check the FAQs on our website (www.noctua.at/faqs) and don’t hesitate to contact our support team at support@noctua.at.

Required mounting parts

Plastic CPU carrier frame

Please note that installing an LGA4677 processor and heatsink requires a plastic CPU carrier frame such as the one shown above. These carrier frames are included with boxed retail CPUs and available separately via Intel sales partners for tray type CPUs. As different CPUs require different carrier frame types (E1A, E1B or E1C), please make sure to purchase the correct carrier frame for tray type CPUs.

Removing the fans

• Take the fans off the cooler. Install the NM-XFB9 brackets to the heatsink using the NM-SSC2 short screws.

Assembly of carrier frame, CPU and heatsink & installation to the socket

Please follow the official Intel installation manual for how to attach the CPU carrier frame to the heatsink, insert the CPU to the carrier frame and install the CPU/heatsink assembly to the socket: www.intel.com/processorinstall

Note that while the Intel illustrations show a 2U heatsink, the Noctua NM-XFB9 brackets use the same mounting parts, so the procedure is identical for Noctua heatsinks.

When attaching the CPU carrier frame to the base of the heatsink, turn the heatsink upside down so that the base is facing upwards. Carefully put it down onto the tips of the heat pipes and secure it with your hand so that it cannot tilt and that the fins cannot get bent. Remove the plastic protective cover from the base of the heatsink and be careful not to damage the layer of pre- applied thermal compound.

Caution: If you are not using the heatsink for the first time and it, therefore, doesn’t have a fresh layer of pre-applied thermal compound anymore, you need to apply a thin layer of thermal compound to the CPU yourself before clipping it to the heatsink. If there are residual traces of previous thermal paste or thermal pads on your CPU or on the heatsink, please clean them off first.

Installing the fans

Reattach the fans to the heatsink using the supplied fan clips

• Connect the fans to the motherboard’s CPU fan header(s). If necessary, use the supplied NA-YC1 y-cable to connect both fans to one fan header.

Removing the heatsink from the socket and the CPU from the heatsink

Please follow the official Intel guidelines for how to remove the heatsink and how to take off the CPU and carrier frame: www.intel.com/processorinstall

Transporting your system

• As it is not possible to reliably calculate or control the forces that act upon a system during transport (e.g. in shipping), we generally recommend, for safety reasons, taking the cooler off.
• Noctua cannot be held responsible for any damage that may arise due to excessive stress during transport if you keep the heatsink installed.

Warranty, support and FAQs

Even with high-grade products and strict quality control, the possibility of defects cannot be eliminated entirely. Therefore, we aim at providing the highest possible level of reliability and convenience by offering a warranty period of 6 years and direct, fast and straightforward RMA service. Should you encounter any problems with your NH-D9

• DX-4677 4U, please don’t hesitate to contact our support team at: support@noctua.at.
• Please also consult the FAQ section on our website: www.noctua.at/faqs

References

• Noctua Compatibility Centre
• Intel® Processor Installation Support for Desktops and Servers
• Support : Noctua Knowledge Centre

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>