Electrolux E5EC1-50ST 1.25L Drip Coffee Machine Instructions

: June 9, 2024
: Electrolux

Table of Contents

Electrolux E5EC1-50ST 1.25L Drip Coffee Machine
USER MANUAL
- SAFETY ADVICE
- GETTING STARTED (picture page 3 and 4)
TROUBLESHOOTING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Electrolux E5EC1-50ST 1.25L Drip Coffee Machine

Electrolux-E5EC1-50ST-1.25L-Drip-Coffee-Machine-product-
image

USER MANUAL

Graphics and drawings in this manual are solely for illustration purposes and are subject to variations from actual product.
Read all instructions carefully before using the appliance for the first time.
Keep this manual for future reference.

COMPONENTS (picture page 2)

Electrolux-E5EC1-50ST-1.25L-Drip-Coffee-Machine-01

A. Power indicator button
B. One-cup indicator/button
C. Two-cup indicator/button
D. Steam indicator/button
E. Brewing head
F. One-cup / E.S.E pod filter cup
G. Two-cup filter cup
H. Filter holder
I. Tamper / measure spoon
J. Cleaning pin*
K. Water tank lid
L. Water tank handle
M. Water tank
N. Cup warmer
O. Steam knob
P. Hot water / steam nozzle (milk frother)
Q. Drip grid
R. Drip tray
available in certain models only

SAFETY ADVICE

Read the following instructions carefully before using the appliance for the first time.

This appliance can be used by children aged from 8 years old and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children unless they are supervised.
Keep the appliance and its cord out of reach of children less than 8 years old.
The appliance may only be connected to a power supply with voltage and frequency comply with the specifications on the rating plate.
Never use the appliance if
- the supply cord is damaged,
- the housing is damaged.
The appliance must only be connected to an earthed socket. If needed, an extension cable suitable for 10 A can be used.
If the appliance or the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person to avoid hazard.
Always place the appliance on a flat, level surface.
The appliance must be switched off and unplugged each time after use, before cleaning and maintenance.
The appliance and accessories become hot during operation. Use only designated handles and knobs. Allow to cool down before cleaning or storage.
The mains cable must not come into contact with any hot parts of the appliance.
Do not remove the water tank during the brewing process.
Do not remove the filter holder during the brewing process or when there’s steam / hot water flowing from the filter holder as the appliance is pressurized. DANGER! There is risk of scalding.
Release pressure through hot water/steam nozzle (follow instruction step 11) before removing filter holder. Warning: Avoid steam burn.
When the steam function is used, there can be some hot water dripping from the brewing head.
DANGER! The water is hot, there is a risk for scalding.
When opening the steam knob, there is a shot of hot water coming out. Be careful and open the steam valve slowly. DANGER! The water is hot, there is a risk for scalding.
Do not immerse the appliance in water or any other liquid.
Do not exceed the maximum filling volume as indicated on the appliances.
Fill the water tank only with cold water, never with milk or other liquids.
Always use fresh water to brew expresso for the best taste.
Do not use the appliance if the water tank has not been filled.
Do not use the appliance without the drip tray or drip grid, unless a higher cup/mug is in use.
Do not use or place the appliance on a hot surface or near source of heat.
Warning: Avoid spillage on the connector.
This appliance is intended for domestic use only. The manufacturer cannot accept any liability for possible damage caused by improper or incorrect use.
This appliance is not intended to be operated by means of an external timer or separate remote-control system.

This appliance is for used in household and similar applications such as:

staff kitchen areas in shops, offices and other working environments;
farmhouses;
used by clients in hotels, motels and other residential type environments;
bed and breakfast type environments.

GETTING STARTED (picture page 3 and 4)

Start the machine for the ﬁrst time

Place the machine on a flat surface. Plug in the machine to turn on its stand-by mode, with button turns half on. Fill the tank with cold pure water. Put filter cup into filter handle, and then secure it onto brewing head anti-clockwise from “INSERT“ to “LOCK“ position without coffee. Make sure the knob is at the horizontal position (“OFF” position).
Start the machine with button, with light turns fully on and buttons start blinking.
When buttons stop blinking, pre-heating is done. Press button to start brewing process.
NOTE: There may be noise when pumping the water for the first time. It is normal. The machine is releasing the air from inside. The noise will stop after about 20 seconds.
When brewing is finished, remove the filter handle clockwise, clean the filter and the drip tray. Now the machine is ready to use.
NOTE: The machine will turn off automatically after 20 mins of no operation. Make espresso coffee
Put one-cup filter cup into filter handle. Add one spoon of ground coffee, press it tight with tamper; or add an E.S.E pod and put it into filter cup. E.S.E (Easy Serving Espresso) Pods can be used to simplify the espresso preparation. Each pre-packed pod contains 7 grams of coffee, already measured, pressed and sealed between 2 fine layers of filter paper.
Attach the filter holder onto the brewing head in anti-clockwise direction from “INSERT” to “LOCK”
position.
Put a warm cup on the drip tray. When pre-heating is done, and and buttons fully light up, press button to start brewing process.
The machine will stop operation when the brewing is done.
To brew 2 cups of espresso at the same time, press button.
NOTE: If both and buttons start blinking quickly, you may simply press or button to cancel brewing, or (step 11)
(step 10) you may restart brewing after cooling down the boiler. Turning the knob to position to release hot water from steam nozzle. The pump stops working automatically when it has cooled down. Turn the knob off and resume brewing.
Make hot water
When pre-heating is done, and and buttons fully light up, turn the knob to position.
Hot water will flow out from the steam nozzle. Turn the knob off when you get the needed amount. Froth milk and make cappuccino/latte
Fill a jug with 100ml (for cappuccino) or 200ml (for latte) milk.
Note: make sure jug diameter is no less than 70±5mm, and jug capacity can hold twice the milk volume after frothed.
When pre-heating is done, and and buttons fully light up. Press button, it starts blinking.
NOTE: Use full milk at refrigerator temperature (NOT HOT!)
When the button stops blinking, steam / milk frothing function is ready. Before frothing milk, push steam nozzle in the direction of drip tray, turn the knob to position to release steam until there’s no water coming out, turn off steam function by turning the knob back to horizontal ”OFF” position.
Immerse steam nozzle in milk about 2cm under the milk surface, turn on the knob. Make sure the steam nozzle is placed in a position that makes the milk turning in one direction inside the jug from top to bottom.
When the desired level of foam is reached, turn off the knob. Note: Clean steam nozzle with wet sponge immediately after steam stops generating. Be careful not to get hurt! The pump automatically stops working after frothing milk for 3 minutes.
Pour the frothed milk into the espresso prepared, now the cappuccino/latte is ready. Sweeten to taste and if desired, sprinkle the froth with a little cocoa powder.
NOTE: After frothing milk, you may immediately make espresso again by pressing or button. If both and buttons start blinking quickly, cool down the boiler and resume brewing (see step 11) DIY / VOLUME
When pre-heating is done, and and buttons fully light up, press and hold / button for 3 seconds to start resetting mode. Press / button to start brewing and press again to stop when the desired volume is reached. Now the volume is saved for next operations.
Restore factory default setting simply by simultaneously pressing / buttons for 3 seconds again.
CLEANING AND CARE
Turn the machine off and unplug the power cord. Let the machine cool down completely before cleaning. Wipe all outer surfaces with a damp cloth. Clean water tank, drip tray and drip grid regularly.
Never use caustic or abrasive cleaners, and never immerse the machine in liquid!
NOTE: only the filter cups are dishwasher safe.
Detach the filter handle by turning it clockwise. Scrap coffee residue or used E.S.E pod. Extract the filter cup from the filter holder, rinse them with clean water and dry thoroughly. DECALCIFYING
Descaling is recommended when all indicators blink 5 times with 5 beeps at the moment machine is turned on. Descaling warning will repeat 2 more times when you turn on the appliance if you do not perform descaling or do not cancel by simultaneously pressing and and for 3 seconds.
Fill the water tank to 300ml level with water and then add the descaling agent (or fill in water and vinegar 1:1). Use only an environmentally friendly descaling agent and always follow the manufacturer’s instructions. When pre-heating is done, and and buttons fully light up, simultaneously press and for 3 seconds to start descaling process, during which and buttons are blinking slowly one after another. When descaling completes, the machine will return to stand-by mode. Perform step 1-4 twice before using the machine.

Enjoy your new Electrolux product!

TROUBLESHOOTING

PROBLEM	POSSIBLE CAUSE	SOLUTION
Water leaks from the bottom of coffee maker.	There is too much water in the
drip tray.	Please clean the drip tray.
The coffee maker malfunctions.	Please contact with the authorized service

facility for repairing.
Water leaks outside of filter cup.| There is some coffee powder on filter edge when attached to the brewing head.| Clean the coffee powder on the filter edge.
Acid (vinegar) taste exists in espresso coffee.| Didn’t perform descaling correctly| Clean up machine according to step 1-4 for “start the machine for the first time”
The coffee powder is stored in a hot, wet place for a long time. The coffee powder turns bad.| Please use fresh coffee powder, or store unused coffee powder in a cool, dry place. After opening a package of coffee powder, reseal it tightly and store it in a refrigerator to maintain its freshness.
The coffee maker cannot work anymore or does not respond at all.| The power outlet is not plugged well.| Plug the power cord into an earthed socket correctly. If the appliance still does not work, please contact with the authorized service facility for repairing.
The steam / milk frothing does not work properly.| The white indicator is not illuminated.| Only after the white indicator is illuminated, the steam station can be used to perform milk frothing.
The container is too big or the shape does not fit.| Use high and narrow cup or professional milk frothing jug.
You have used skimmed milk| Use whole milk or half-skimmed milk.
Steam indicator blinking quickly| Continuously steaming for 3 minutes and the steam knob is not reset.| Reset steam knob to “OFF” position.
One-cup indicator and two-cup indicator blinking quickly| Dispense 40ml of hot water and the steam knob is not reset.| Reset steam knob to “OFF” position.
The steam knob is not reset after cooling down.
Boiler temperature is too high.| Cool it down by perform STEP 11
One-cup indicator, two- cup indicator and steam indicator blinking quickly| The steam knob is not reset, but the machine is turned on| Reset steam knob to “OFF” position
ALL indicators blinking at the same time for 5 times| Need descaling| Perform decalcifying
Filter handle is too tight to operate| Fill too much coffee powder in the filter cup.| Fill filter cup with less coffee powder
Coffee flows drip by drip| Too much coffee powder| Fill filter cup with less coffee powder
Coffee powder is too fine, and tamped too tight| Use coarser coffee powder or tamp coffee powder with less force
Filter cup is blocked| Clean the filter cup with cleaning pin

DISPOSAL
Recycle the materials with the symbol . The packaging materials can be recycled. Please sort individual components by type and dispose them in applicable containers according to local disposal instructions. Recycling of packaging materials reduces the use of raw materials and amount of waste in landfill sites. Help protect the environment and human health by recycling your packaging.

Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.

Electrolux reserves the right to change products, information and specifications without notice.

KOREA
Electrolux Korea limited
9F, Pine Avenue B,
100 Euljiro, Jung-gu, Seoul, Korea 04551
Korea
Tel : +82 2 6020-2200
Fax: +82 2 6020-2271~3
Customer Care Services : +82 1566-1238
Email : homecare.krh@electrolux.com
Website: www.electrolux.co.kr

INDONESIA
PT. Electrolux Indonesia
Electrolux Building 2nd Floor
Jl. Abdul Muis No 34,
Jakarta Pusat 10160
Indonesia
Tel: +62 21 5081 7303
Fax: +62 21 5081 8069
SMS/WA : 0811-8339-777
Customer Care Services: 0804111 9999
Email: customercare@electrolux.co.id
Website: www.electrolux.co.id

PHILIPPINES
Electrolux Philippines, Inc.
12th Floor, Cyber Sigma Building
Lawton Avenue, Mckinley West, Fort Bonifacio Taguig City, Philippines 1634
Domestic Toll Free: 1-800-10-845-CARE (2273)
Customer Care Services: (02) 845-CARE (2273) / (02)-8845-4663
Email: wecare@electrolux.com
Website: www.electrolux.com.ph

THAILAND
Electrolux Thailand Co Ltd
Electrolux Building
14th Floor 1910 New Petchburi Road
Bangkapi, Huay Kwang
Bangkok 10310
Thailand
Tel: +66 2 725 9100
Fax: +66 2 725 9299
Customer Care Services: +66 2 725 9000
Email: customercarethai@electrolux.com
Website: www.electrolux.co.th

VIETNAM
Electrolux Vietnam Ltd
Floor 10, Soﬁc Tower, 10 Mai Chi Tho,
Thu Thiem Ward,
Thu Duc City
Ho Chi Minh City
Vietnam
Tel: +84 8 3910 5465
Fax: +84 8 3910 5470
Customer Care Services: 1800-58-8899
Email: vncare@electrolux.com
Website: www.electrolux.vn

MALAYSIA
Electrolux Home Appliances Sdn Bhd
Lot C6, No. 28, Jalan 15/22,
Taman Perindustrian Tiong Nam,
40200 Shah Alam, Selangor
Malaysia
Customer Care Services Tel: +60 3 5525 0800 Customer Care Services Fax: +60 3 5524 2521
Email: malaysia.customercare@electrolux.com
Website: www.electrolux.com.my

SINGAPORE
Electrolux SEA Pte Ltd
351 Braddell Road #01-04
Singapore 579713
Customer Care Services: +65 6727 3699
Email: customer-care.sin@electrolux.com
Website: www.electrolux.com.sg

UAE
ELECTROLUX APPLIANCES
MIDDLE EAST DMCC,
P.O.BOX 336148, Unit No. 4001,
MAZAYA BUSINESS AVENUE BB1, JUMEIRAH LAKE TOWERS, Dubai,
United Arab Emirates