BOSCH GTA570 Folding Table Saw Scissor Stand Instruction Manual

BOSCH GTA570 Folding Table Saw Scissor Stand

Call Toll Free for Consumer Information & Service Locations
1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

Safety Symbols

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

| This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
| DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
| WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
| CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

Safety Instructions

Read all instructions. Fail-ure to follow all instructions listed below may result in serious personal in-jury.
Fully assemble and tighten all the fasteners required for this stand. Periodically check that all fasteners are attached and adjusted according to the assembly instructions in-cluded in this manual. A loose stand is un-stable and may shift in use and cause serious injury.
Turn tool switch off and disconnect power before mounting to the stand. Unintended startup during assembly can cause injury. Before operating make sure the entire unit is placed on a solid, flat, level surface. Serious injury could occur if tool is unstable and tips.
Never stand on tool or its stand or use as lad-der or scaffolding. Serious injury could occur if the tool is tipped or the cutting tool is acci-dentally contacted. Do not store materials on or near the tool such that it is necessary to stand on the tool or its stand to reach them.
Use only Bosch replacement parts. Any oth-ers may create a hazard.

Intended Use

Use this stand only as in-tended. Unintended use may result in personal injury and property damage.
This stand is intended to be used only with the Bosch GTS18V-08 table saw.
Do not use this stand with any other Bosch or competitive brand table saws.

Unpacking and Checking Contents

Separate all parts from the packing materials, and check each one with the Package Contents list to make certain all items are accounted for before discarding any packing material.

GTA570 Table Saw Stand Package Contents

Qty.| Part Description
1| Stand Subassembly
2| Front Legs (marked “A” and “B”)
2| Back Legs (marked “C” and “D”)
4| Phillips Head Screws
4| 7/16″ Hex Lock Nuts

Tools Needed for Assembly

(Fig. 1)
To assemble the stand, you will need the following tools:

• Phillips Head Screwdriver
• 7/16″ hex socket wrench or open end wrench

Assembling the Stand

(Fig. 2)

1. Each of the Legs is marked (“A,” “B,” “C,” and “D”), and there are matching markings on the corners of the Stand Subassembly 1. Slide each Leg into the matching locations on the Stand Subas-sembly 1.
   Note: The stand’s legs are not interchange-able.

2. Align the Holes in Each Leg with the Holes in the Stand Subassembly.

3. Insert the Phillips head screws through each of the legs, and tighten securely with the hex lock nuts. Make sure that the heads of the Phillips head screws are on the outside of the stand assembly.
   

Mounting the Saw to the Stand

(Fig. 3, Fig. 4, Fig. 5)

1. Unfold the stand to the open position
2. Slide the table saw onto the stand so that the Rear of the Base 2 slides under the stand’s Retainer Tabs 3 . Make sure the saw is centered on and located inside the L- Shaped Brackets 4 on the front of the stand.
3. Once the rear of the Table Saw Base 2 is fully aligned under the stand’s Retainer Tabs 3, latch the Wire Hook 5 of the Clamp 6 on the front of the stand onto the tube of the Saw Base 2 , and lock the  Clamp 6 into place
   Note: To remove the saw from the stand, re-verse the procedure above.

Transporting the Stand

Your GTA570 Table Saw stand is designed for easy transport.
To prepare the stand for transport:

1. If a table saw is mounted on the stand, remove the saw. (See “Mounting the Saw to the Stand” on page 4.)
2. Fold up the stand.

Maintenance

To reduce the risk of injury, periodically check that all fasteners are attached and adjusted accord-ing to the assembly instructions included in this manual.

Service
NO USER SERVICEABLE PARTS. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Ser-vice Station.

This page was intentionally left blank

LIMITED WARRANTY OF BOSCH PORTABLE AND BENCHTOP POWER TOOLS

Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all BOSCH portable and benchtop power tools will be free from defects in mate-rial or workmanship for a period of one year from date of purchase. Seller’s sole obligation and your exclusive remedy under this Limited Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts, without charge, which are defective in material or workmanship and which have not been misused, carelessly handled, or misrepaired by persons other than Seller or Authorized Service Station. To make a claim under this Limited Warranty, you must return the complete portable or benchtop power tool product, transportation prepaid, to any BOSCH Factory Service Center or Authorized Service Station. For Authorized BOSCH Power Tool Service Stations, please refer to your phone directory.
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.
ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE YEAR FROM DATE OF PURCHASE. SOME STATES IN THE U.S., SOME CANADIAN PRO V INCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROV-INCE TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.
THIS LIMITED WARRANTY APPLIES ONLY TO PORTABLE AND BENCHTOP ELECTRIC TOOLS SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA AND THE COM-MONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL BOSCH DEALER OR IMPORTER.

© Robert Bosch Tool Corporation 1800 W. Central Road Mt. Prospect, IL 60056-2230 Exportado por: Robert Bosch Tool Corporation Mt. Prospect, IL 60056-2230, E.U.A.
Importado en México por: Robert Bosch, S.A. de C.V., Calle Robert Bosch No. 405, Zona Industrial, Toluca, Edo. de México, C.P. 50070, Tel. (722) 2792300

References

• Bosch Power Tools | Boschtools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>