JQVV V309 Dash Cam User Manual

JQVV V309 Dash Cam

Foreword

Thank you for purchasing our dash cam.

1.  Please format the Mirco SD card before recording.
2.  Had better format the Mirco SD card per week to avoid recording overmuch locked videos.(Avoid Mirco SD card memory is full).
3.  Please tear off the film on the surface before use.
4.  Please remember to Remove the Lens Film before recording the video.
5. To use parking monitor, please connect Smart HardWire Kit. If you meet any problems about the dash cam, please contact us as soon as possible.

What do You get In the Box?

1.  3.0 IPS LCD Dash Camera
2.  1080P Inside Type Rear Camera
3.  Suction Cup Bracket
4.  Car Charger(With USB Port)
5.  Short USB Cable
6.  4 x Cable Clamps
7.  1 x Crowbar
8.  GPS
9.  User Manual

Notice:
Mirco SD card is NOT included in the packaging.

Interface and Button Function

1.  Speaker
2.  Lens
3.  Up
4.  Menu/Mode
5.  Down
6.  Power
7.  Micro SD Card slot
8.  ok button
9.  USB Power-In
10.  Rear Camera Connector
11.  Mount Bracket
12.  Reset
13.  Microphone

Product Use Precautions

Please insert the Mirco SD card before recording.

NOTE:
Mirco SD card is NOT included in the packaging.  We recommend U3 speed Mirco SD Card for the dash cam .

Install and remove the Mirco SD card:

1.  Insert the Mirco SD card into the Mirco SD card slot in the correct direction until the Mirco SD card is fixed in the card slot.
2.  When removing the Mirco SD card, please gently press down the Mirco SD card, and then take it out after the Mirco SD card is ejected.
3. Please do not pull or insert the Mirco SD card when the machine is working to avoid damage.
4.  When you insert the Mirco SD card into the machine, the machine will set the Mirco SD card as the default storage device, and the original Mirco SD card data may not be readable.
5.  If the Mirco SD card is not compatible with the machine, please re-insert it or another Mirco SD card and try again. Please use the attached USB car charger to charge this machine. If the output voltage is too large or too small, it will cause the machine to not work properly and unpredictable problems.
6.  Please use the car charger that comes standard with this machine to power the machine, otherwise it will cause damage to the machine.
7.  Install the rear camera on the rear of the vehicle, paying attention to the direction when installing. The wiring can be laid along the roof of the vehicle. After the installation is complete, connect the rear plug to the rear camera interface of the recorder.

Set up and Installation

The GPS module should be installed on the top edge of the windscreen, fixed with a sticker.

Set up and Installation

1.  Use the suction cup mount to install the dash cam on the windshield, recommended place near the rearview mirror facing front, adjust the lens angle for best coverage.
2.  Plug the included power adapter (car charger) into the car cigarette lighter socket.
3.  Connect the power cable to the camera. For better looking, route the excess cable alongside the interior trim as the diagram shows.
4.  While routing the cable,make sure the GPS module is in right place: The module should be installed near the top edge of the windscreen with the sticker applied to the windshield. The stamped side of the module facing the inside of the car, and the sticker should always be facing outside it the car.
5.  Connect the rear camera, install ii as follow (the picture).
6.  After installation, please start the engine to make sure dash camera works well.

Button Function

UP

| ·In Setting Menu.

Short press to select option and adjust values.

·In Playback.

Short press to select media files.

·In Video mode.

Short press to switch front and rear camera view.

MENU/

Mode

| ·Short press to access the menu settings in video mode, long press to manually lock current video file.

·In standby(not actively recording), long press to switch mode: Video/Photo/Playback.

Down

| ·In Setting Menu.

Short press to select option and adjust values.

·In Playback.

Short press to select media files.

·In Video mode.

Short press to turn on/off audio recording.

· Long press to turn on/off the Wi-Fi

OK

| · In Video Mode.

Short press to start/stop video recording.

Long press the OK Botton to open the ACC parking monitor.

· In Photo Mode.

Short press to take a photo.

· In Setting Menu.

Short press to confirm selection and adjustment.

· In Playback, short press to select and play recorded files.

· In Playback, short press to stop/start playing video.

Power

| · Long press to turn off/on the camera.

·Short press to turn off/on the display.

Operating Mode

The dash cam operates in 3 modes: Video Recording Mode,Photo Mode and Playback Mode. Video Recording Mode and Photo Mode also have menu to help you configure. In standby condition(non-recording state), LONG PRESS
“MENU/Mode” button to switch between different modes and access the mode you want. Watch the icon on top left corner of the screen for each mode.

Video recording Mode
The camera will automatically enter Video Recording Mode and start recording when connected to a car charger and power on. A Red dot flashing on the top left corner indicates recording is in progress. Press the “OK” button to stop recording, or start recording again.

Video Recording Mode

1.  Recording Mode
2. Recording Indicator
3.  G-sensor Icon
4.  Recording Time
5.  Loop Recording
6.  Exposure
7. Parking Mode Off by default
8.  Audio Recording Icon
9.  Date
10.  Time
11. Power
12. Mirco SD Card
13. GPS
14. Wi-Fi
15.  Video Resolution

Photo Mode

1.  Photo mode
2.  Explosure
3. white balance
4. 1S0
5.  Number of photos that can be taken
6. photo resolution
7.  Quality
8.  Mirco SD card
9.  Charging

Playback Mode

Press the MENU BUTTON to switch to the following interface

Press the MENU BUTTON again to switch to the setting interface

Video Menu Setting

| Resolution| Adjust video resolution
---|---|---

Loop Recording

|

Adjust Loop Recording video clip length

Record Audio| Turn ON/OFF audio recording
G-Sensor| Adjust G-sensor lock sensitivity

Parking Monitor

| To use parking monitor, please connect Smart HardWire kit
Date Stamp| Setting the date

WDR

| The WDR (Wide Dynamic Range) technology on this camera allows it to adapt to the recordings from the surroundings. When over or underlit the camera adjusts the quality to ensure a constant great quality video
Exposure| Setting the value

Car Number

| Set up your car license plate number, and watermarked in video

WIFI

| Share the video and set the parameter value on the downloaded APP

Setup

| Screen Saver| Setup the screen saver activated time

Frequency

|

Setup local power frequency

Beep Sound| Turn ON/OFF operation prompt
Language| Setup the system menu language
Datemme|

Setup local date and time

Format| Format SD Card
Version| Check softerware version

Auto Power Off

| In standby mode (not actively recording

orplayback video), the machine will automati­ cally turn off after a period of no operation

Function

Loop Recording
A dashcam can loop and record the video automatically. Please set loop recording as 1 minute/2 minutes/3 minutes instead of setting”OFF”.

Wide Dynamic Range
WDR technology on this camera allows it to adapt to the recordings from the surroundings. When over- or underlit the camera adjusts the quality to ensure a constant great quality video.

Dual Dash Cam
Front camera supports(4k/2.5k/1 0B0p)resolution. Rear camera supports 1080p resolution.

Gravity Sensing
When the car collides, record ii and save ii as video urgently and do not delete it. It helps offer you irrefutable evidence.The locked videos won’t delete automatically. Had better clear the Mirco SD card per week to avoid that memory is full.

Super Night Vision
There is no doubt that the dash cam with 4k front camera can freely record at night.

Automatic On / Off
Support the connection of vehicle power supply, the car starts the video. When we stops the engine, the video automatically saves the video and turns off.

Wi-Fi Function

1.  Search ‘DashGo’ on Apple store or Google play, then download and install this software on your phone.
2.  Open ‘WLAN’ of the phone and camera simultaneously. (Long press ‘Down’ key to open Wi-Fi of camera or turn on Wi-Fi option in the menu after turning on camera)
3. . Select the corresponding Wi-Fi name of the camera is: JQW-V309 then enter the password, default password is:12345678
4.  After connecting successfully, back to APP to view real-time view, take video/photo, video/photo playback etc. It also offers us the opportunity to share the video and set the parameter value on the downloaded APP.
5.  Click the setting button to change your customized settings.

GPS Function
The device is equipped with GPS positioning module for synchronously recording the complete driving track information by the user, the GPS info will be shown in the video playback, such as speed, latitude and longitude. User can view the footage and all GPS information in the PC GPS viewer, named “DashGo”. The GPS playback needs a customized player “DashGo”, for PC OPERATING SYSTEM system only. Please contact customer service support “DashGo” download.)

Parking Monitor(Optional)
Parking monitor is OFF by default.With optional Smart Hardwire kit connected, the Parking Monitor is enabled, the dash camera will stay standby after the engine is turned off. When camera detects shaking, it will automatically tum on and take a short video , then return to standby automatically. (To use parking monitor, Must connect Smart HardWire kit.)

The details of ACC parking monitor
Notice: Pay attention to the following content before car shuts down and the machine is connected to the Smart HardWire Kit.(Before you get out of the car)

1.  Long Press the OK button to enter the ACC parking monitor mode, the parking monitoring icon will be displayed on the main recording interface (when the parking monitor is not in progress, this icon is to be off), the machine will enter the standby mode without recording, the screen saver would release 10 seconds later. The recording time of each video is 1 minute. The videos will be saved in the playback folder.
2.  The way to trigger parking monitoring is G-sensor, motion detection triggers, and the machine records after triggering .(the screen does not light up at this time)
3.  (Before you start your car}Short press any key to exit the parking monitoring mode and enter the normal recording mode”

ATTENTION!
The dash cam would delete the video (which is unlock) if the Mirco SD card is full.

Model:

|

V309

---|---
Screen Display:| 3 inch LCD Screen

Lens:

|

170°Wide Angle Lens

Video Resolution:

| Front:3840’2160P Rear:1920’10B0P
Video Format:| MP4
Video Coding:| High compression H.264
Video Mode:| Loop Recording
Picture Format:| JPG
Loop Recording:| Built-in

Parking Monitor:

| To use parking monitor, please connect Smart HardWire kit
G-Sensor Lock:| Built-in
Storage:| Micro SD Card Up to 256GB
Operating Temperature:| -20°C- 60°C(-4°F- 140 “F)
Storage Temperature:| -30 °C- ?0°C(-22″F- 158°F)
Operation Humidity:| 15~85 %RH
Power Supply:| DC SV/3A

FCC STATEMENT

FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:?(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance between 20cm of the rad or your body: Use only the supplied antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>