AIPER Orca 800 Mate Robotic Pool Cleaner User Manual

AIPER Orca 800 Mate Robotic Pool Cleaner

Important Precautions

1. Read the manual carefully, and use the cleaner according to the manual. We are not liable for any losses or injuries caused by improper use.
2. To avoid any accidents/damages, please fix the power supply unit 11.5ft (3.5m) away from the swimming pool by using the included safety rope, in case it falls into the water and result in potential danger.
3. To prevent severe damages to the cleaner, never power on the unit when it is outside of the swimming pool.
4. The power cord must be connected to an appropriate earthed socket and the power connector must be plugged in tightly.
5. Hold the top handle when putting the cleaner into water or lifting out of the water, do not pull the cable. Before powering on, make sure to empty the trapped air inside the cleaner (no more air bubbles come from the cleaner and the cleaner is fully submersed on the pool floor).
6. Before powering on, make sure the filter tray is assembled in position and the cord is fully released to avoid any winding, which could affect the cleaner’s performance or cause damages.
7. Please clean and wash the filter tray every time after use.
8. The cleaner should be stored in a cool and ventilated place, away from direct sunlight when it’s not in use.
9. The power supply unit should be placed at a shaded area during working. To avoid overheating and potential damages of components, never cover the power supply unit during working.
10.  Only authorized after-sales service personnels can open the cleaner’s power supply unit and motor assembly, otherwise the warranty will be invalidated.
11. Do not use the cleaner beyond the working environment/conditions stated in this manual.
12. Make sure the PH value of the pool water is between 7.0~7.4.
13. This machine is to clean the pool only not for other purposes.
14. Do not use the cleaner immediately after spraying the pool chemicals and do not use the cleaner as a dosing machine, which will damage and corrode the parts.
15. Do not operate the cleaner when there are people or animals in the pool.
16. Take the cleaner out of the swimming pool after use. If the cleaner is immersed in the water for a long time, there will be micro organisms produced.
17. The cord should be untwisted and wrapped properly after use.
18. Use the original adapter only for the control box kit.
19. Do not operate the cleaner while pool filter is running.
20. Do not allow children to ride on the cleaner or play with it.

Introduction

The robotic pool cleaner Orca 800 Mate is a new type of highly efficient and energy-saving swimming pool cleaning robot. Through its advanced computer- controlled program, it cleans the pool floor (even with an max slope 30°)automatically. At the same time, it filters the pool water and gets rid of suspended particles without replacing the pool water. It’s totally environmental-friendly.

Read the user manual carefully before use.

Specifications

Operations

Attentions:

1. When putting the cleaner into the water, please hold the top handle and make sure to empty the trapped air inside. Now, the cleaner can be immersed to the pool floor.
2. When pulling the cleaner out of the water, suspend the cleaner on the water for about 10-15 seconds to empty the water inside. Please hold the top handle only; never pull the cable.
3.  Please install the swing plate and brush before use for normal working.
4. Please use the included safety rope to fix the power supply unit away from the pool in case it falls into the water.

Control Panel and Indicator Instructions

Functions & Adjustments of Nozzles

There are two nozzles on the cleaner, one of them opens when the other closes. Water flows out through the open nozzle to thrust the cleaner to move forward. Adjust the nozzle by turning it to control the moving route.

• Settings of nozzle angle and moving route
  Sketch: the nozzles of the cleaner are marked with angles (0°-40°). The cleaner moves in an approximately straight line when the nozzle angle is 0°. The cleaner moves in a more curved line at a larger angle from 0°-40°.

• Recommended three cycles and nozzle settings

Setting One: default setting: 0°–20°, for most of the pools.
Setting Two: 0°–40°, when the cleaner does not have full coverage of the pool.

Setting Three: 20°–20°, for round pools

Note: These are recommended settings and different settings might to specific pools. So the operator can adjust the settings according to the principle of nozzle settings and the actual situation of the pool.

Filter Cleaning

Open the cleaner by clips

Take out the filter tray

Wash the filter tray and chassis

Reassemble the cleaner and clip on

Trouble Shooting

Remark: The pool water condition must be within the following parameters:

• PH: 7.0 —7.4
• Temperature: 10°C(50°F) to 35°C(95°F)
• Salt: Max 5,000 ppm
• Chlorine: Max 2 ppm

Packing List

Warranty

1. This product is covered by Aiper warranty for 24 months ( only for driving kit and control box kit) from the date of purchase. Consum- able parts are beyond warranty which include Filter Tray/Brush/ Wheels/Nozzles.
2. This warranty is voided if the product has been altered, misused, or has been repaired by unauthorized personnels.
3. The warranty extends only to manufacturing defects and does not cover any damage resulting from mishandling of the product by the owner.
4. the order number or record must be presented for any claim or repair during the warranty period.

Aiper Customer Service:
US Toll Free: 1-866-850-0666
Email: service@aiper.com
Facebook: @AiperOfficial

References

• Aiper | The World's Best Cordless Robotic Pool Cleaner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>