HOBBYWING ZYD7002 Remote for Skateboard User Manual

ZYD7002 Remote for Skateboard
User Manual

ZYD7002 Remote for Skateboard

Thank you for purchasing this HOBBYWING product! Any improper use may cause malfunction and damage to devices, so please make sure to read through this manual  before use and strictly abide by the prescribed operating procedures. We are not liable for any liability arising from the use of this product, including but not limited to the  compensation for incidental or indirect loss. We also do not bear any responsibility for unauthorized modification of the product. We have the right to change the product  design, appearance, performance and use requirements without notice.

Product Specification

Interactive mode

Diagram of remote control：

Function and operating instructions

1. Power on
   Press “button A” on remote control for 1 second to power on. The remote control will vibrate shortly and enter into connection mode. OLED screen displays main  interface or unconnected hint according to connection state. Then press the power button of skateboard for 0.2 second to enter into connection mode.
   Note: The normal state after connection is that OLED screen displays main interface and indicator light of skateboard is constantly on.

2. Power off
   Manual off: Press “button A” for 2 seconds to power off (The skateboard cannot be powered off under speeding). The remote control vibrates shortly, press power button for 1 second to power off.
   Note: If the skateboard is powered off but the remote control is not powered off and in the state of connection, the screen of remote control displays not connected,  and the remote control vibrates shortly to remind. If the remote control powers off in the state of connection, the skateboard will start to brake and power off after 5  minutes of standstill.
   Automatically off: The remote control and skateboard will power off automatically if not being operated within 5 minutes, if the skateboard is at rest.

3. Connect and match(Have been matched well after leaving factory)
   Both of remote control and skateboard are powered off, first press switch button of skateboard for 5 seconds, the indicator light is red and flashes quickly, reminding  enter into matching state, press “button A” for 5 seconds again, the screen displays matching and enter into matching mode. The remote control displays matching  successfully, with two short vibration and once long vibration means completing matching. After that, the red indicator light of skateboard is constantly on and can be used. After matching remote control, need to select speed, mileage unit and motor diameter, detailed operation method. Button B to switch option. Button A to confirm. The remote control will enter into main function interface after the second motor diameter chosen.

4. Battery indicator
   Battery indicator of remote of control: There are 5 grid power. After power on, if the battery of remote of control is less than 10%(It can be used for 30 minutes at most), the screen of remote control indicates that the power is less than 10%, with a double long vibration. When the battery is only 5%(It can be used for 15 minutes). The remote control reminds the battery is less than 5% again, with a double long vibration.
   When the battery is lower than safe voltage(3.4V) and connected with skateboard, if the skateboard stops, the remote control vibrates once and powers off automictically

5. Battery indicator of skateboard: There are 5 grid power. When the battery of skateboard is lower than 25%, the screen of remote control indicates the battery is lower than 25%, with a double long vibration.

6. When the battery of skateboard is lower than 10%, the remote control will indicates the battery is lower than 10%, with a double long vibration. When the voltage is lower than safe voltage, close power output, brake immediately at this time.

7. Throttle/Brake control
   Push forward “finger dial of throttle” to control forward. Pull backward “finger dial of throttle” to control brake.
   Make sure the finger dial of throttle is in neutral position before power on, or else it will affect the use experience. The screen will remind to return throttle in neutral position if it is not when power on. Please operate as per instruction.

8. Switch direction of skateboard
   In the state of forward, double click “Button B”, the remote control will short vibrate once(short vibrate for 100ms, the same below), the direction icon changes to“Backward arrow”;
   In the state of backward, double click “Button B”, the remote control will short vibrate once, the direction icon changes to “Forward arrow”.
   Note: This operation will be valid when the throttle trigger is in neutral position(zero throttle) and the speed is less than 3km/h.

9. Gear switch Short press button B, the remote control switches to the next gear, with a short vibration. The gear icon will change accordingly.
   Note: This operation will be valid when the throttle trigger is in neutral position(zero throttle).

10. Charging
    ① Charging remote control: When charging the remote control, it vibrates short. The remote control screen displays the charging progress in real time in the form of flowing water light;
    Note: It can not be operated when charging the remote control. It will automatically power off after unplug the charging wire and short vibrate once.
    ② Charging battery of skateboard: When power off, the skateboard enters into charging state automatically if connects the charger.
    The red indicator light is on. When power on, connect the charger to enter into charging state, the red indicator light is on, it will automatically power off after unplug the charging wire.
    Note: When in the state of charging, part of motor and ESC will stop working if the skateboard is not connected with remote control, or does not accept operation instruction.

Malfunction warning instruction:

1. Overcharge (when going downhill with a fully charged battery)
   In principle, going downhill with a fully charged battery is prohibited, because the battery will be charged when braking during the going-downhill process, so going  downhill with a fully charged can shorten the service life of the board battery or even cause accidents like an explosion or a fire. The user needs to consume some power  before going downhill. If some user violates the rule and goes downhill with a fully charged battery, the remote will vibrate and the board power indicator flashes in this  way when ESC detects the battery voltage is too high. If the user continues to go downhill, the board will brake automatically to prevent user from doing that. This method can only protect the battery to a limited extent and  cannot 100% guarantee for the battery safety.

2. Signal loss warning
   When the signal is lost suddenly, the screen of the remote control indicates disconnection, with a short vibration.

3. If the skateboard is accelerating, first the acceleration will stop slowly, then brake slowly automatically. If the skateboard is not accelerating, it will brake slowly. If the  signal is lost, the remote control will search the device of skateboard, if it succeeds in searching and reconnecting, the remote control will short vibrate, the brake will be  cancelled and return to normal operation.

4. Lock-up warning
   When the motor is lock-up or completely struck, the remote control will short vibrate continuously and intermittently, the screen of remote control indicates lock-up.
   If that happens, the user should stop running skateboard and check whether there is foreign matter struck in it, clear the foreign matter and run it again.

5. Overheating warning
   When the operating temperature of motor is higher than 100℃ or lower than 0℃, the remote control vibrates and the screen Indicates overheat and the motor will stop working.
   Note: The user should pay attention to the temperature of motor. Stop using if the operating temperature of motor is high, reuse after the temperature reduces.

6. Overcurrent warning
   When the operating current of motor exceeds the value allowed, the screen of remote control indicates overcurrent, the motor Stops working.
   Note: Close the skateboard and repower on. It can be used after the current returns to normal.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this  device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not  installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>