RYOBI RLT3525 Trimmer Electro User Manual

: June 9, 2024
: RYOBI

RYOBI RLT3525 Trimmer Electro

RYOBI RLT3525 Trimmer Electro

FIGURES

Operating Instructions

Important! It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.

Safety, performance, and dependability have been given top priority in the design of your electric lawn trimmer/edge trimmer.

INTENDED USE

The electric lawn trimmer/edge trimmer is only intended for use outdoors by a standing operator. The product is designed for cutting grass, light weeds, and other similar vegetation at or about ground level. The cutting plane should be approximately parallel to the ground surface when trimming and approximately vertical when edging. The product should not be used to cut or trim hedges, bushes, or other vegetation where the cutting plane is not at or about ground surface level. Do not use the product for any other purpose.

GENERAL SAFETY WARNINGS

WARNING

When using the product, the safety rules must be followed. For your own safety and that of bystanders, please read these instructions before operating the product. Please keep the instruction safe for later use.

WARNING

The product is not intended to be used by children or persons with reduced physical, mental or sensory capabilities. Children should be adequately supervised to ensure they do not play with the product.

WARNING

Some regions have regulations that restrict the use of the product. Check with your local authority for advice.

TRAINING

Never allow children or people unfamiliar with these instructions to use the product. Local regulations may restrict the age of the operator.
Read the instructions carefully. Be familiar with all controls and the proper use of the product.
Keep bystanders, children, and pets 15 m away from the area of operation. Stop the product if anyone enters the area.
Never use the product when you are tired, ill or under the influence of alcohol, drugs or medicine.
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property.

ELECTRICAL SAFETY

Power plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid unintentional starting. Always check that the switch is in off position before plugging in the product to the power supply. Do not carry a plugged in product with your finger on the switch.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not operate the product when there is a risk of lightning.
Do not expose the product to rain or wet conditions. Water entering an appliance will increase the risk of electric shock.
Electrical power should be supplied via a residual current device (RCD) with a tripping current of not more than 30 mA.
Before every use, examine the power cord for damage. If there are signs of damage, it must be replaced. Always uncoil the power cord during use; coiled cables can overheat.
If you need to use an extension cable, ensure it is suitable for outdoor use and has a current capacity sufficient to supply the product. The extension cord cable should be marked with either “H05RN-F” or H05 VV-F”. Check it before every use for damage. Always uncoil it during use because coiled cables can overheat. Damaged extension cables should not be repaired; they should be replaced with an equivalent type.
Do not use the product if the electric cables are damaged or worn.
If the power cord or extension cable becomes damaged during use, disconnect from the power supply immediately. Do not touch the electric cables until the power supply has been disconnected.
Make sure the power cord is positioned so that it cannot be damaged by the cutting means and will not be stepped on, tripped over, or otherwise subjected to damage or stress.
Never pick up or carry the product by the electric cable.
Keep the power cord away from heat, oil, and sharp edges.
Make sure voltage is correct for your product. A nameplate on the product indicates the product’s voltage. Never connect the product to an AC voltage that differs from this voltage.
Make sure the switch is in off position before disconnecting from power supply

PREPARATION

Wear full eye and hearing protection while operating the product. If working in an area where there is a risk of falling objects, head protection must be worn.
Hearing protection may restrict the operator’s ability to hear warning sounds. Pay particular attention to potential hazards around and inside the working area.
Wear long trousers, boots, and gloves. Do not wear loose fitting clothing, short trousers, jewellery of any kind, or use with bare feet.
Secure long hair so it is above shoulder level to prevent entanglement in moving parts.
Before use and after any impact, check that there are no damaged parts. A defective switch or any part that is damaged or worn should be properly repaired or replaced by an authorised service centre.
Make sure the cutting attachment is properly installed and securely fastened.
Never operate the product unless all guards, deflectors, and handles are properly and securely attached.
Consider the environment in which you are working. Keep the working area free from wires, sticks, stones and debris that if struck by the cutter, can become thrown objects.

LAWN TRIMMER / EDGE TRIMMER SAFETY WARNINGS

Use the product in daylight or with good artificial light.
Avoid using on wet grass.
Do not walk backwards when using the product.
Keep firm footing and balance. Do not overreach. Overreaching can result in loss of balance. Always be sure of your footing on slopes. Walk, never run.
Keep bystanders, children and pets 15 m away from the area of operation. Stop the product if anyone enters the area.
Keep the cutting attachment below waist level.
Never operate the product with damaged guards or without guards in place.
Never fit a metal replacement line.
Keep hands and feet away from the cutting means at all times, especially when switching on the motor.
Beware, the cutting elements continue to rotate after the motor is switched off.
Beware of objects thrown by the cutting means. Clear debris like small stones, gravel and other foreign objects from the work area before starting operation. Wires or string may become entangled with the cutting means.
Switch off and disconnect from the power supply before:
- servicing
- leaving the product unattended
- cleaning your product or clearing a blockage
- changing accessories
- checking for any damage after hitting a foreign object
- checking for any damage if the product starts to vibrate abnormally
- performing maintenance
The small blade fitted to the lawn guard is designed to trim the new extended line to the correct length for safe and optimum performance. It is very sharp; do not touch it, particularly when cleaning the product.
Always ensure that ventilation openings are kept clear of debris.
Make sure the cutting head attachment is properly installed and securely fastened.
Make sure all guards, deflectors, and handles are properly and securely attached.
Do not modify the product in any way. This may increase the risk of injury to yourself or others.
Use only the manufacturer’s replacement cutting line. Do not use any other cutting attachment.
Immediately switch off and disconnect from the mains in the event of accident or breakdown. Don’t operate the product again until it has been fully checked by an authorised service centre.

TRANSPORTATION AND STORAGE

Stop the product and allow it to cool down before storing or transporting. Always disconnect from the power supply and wind the cable to prevent damage.
Clean all foreign materials from the product. Store it in a cool, dry, and well-ventilated place that is inaccessible to children. Keep away from corrosive agents, such as garden chemicals and de-icing salts. Do not store outdoors.
For transportation in vehicles, secure the product against movement or falling to prevent injury to persons or damage to the product.

MAINTENANCE

WARNING

Use only original manufacturer’s replacement parts, accessories, and attachments. Failure to do so can cause possible injury, poor performance, and may void your warranty.

WARNING

Servicing requires extreme care and knowledge and should be performed only by a qualifi ed service technician. For service, bring the product to an authorised service centre for repair. When servicing, use only identical replacement parts.

Switch off and disconnect from the mains before conducting any maintenance or cleaning work.
You may make adjustments and repairs described in this manual. For other repairs, contact the authorised service agent.
For the replacement line, use only nylon filament line of the diameter described in the specification table of this manual.
After extending the new cutter line, always return the product to its normal operating position before starting.
After each use, clean the product with a soft dry cloth. Any part that is damaged should be properly repaired or replaced by an authorised service centre.
Check all nuts, bolts, and screws at frequent intervals for proper tightness to ensure the product is in a safe working condition.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:

Injury caused by vibration
- Hold the product by designated handles and restrict working time and exposure.
Injury caused by exposure to noise
- Wear hearing protection and limit exposure.
Injury caused by flying debris
- Wear eye protection at all times

RISK REDUCTION

It has been reported that vibrations from hand-held products may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness and blanching of the fingers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of the symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:

Keep your body warm in cold weather. When operating the product, wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
After each period of operation, exercise to increase blood circulation.
Take frequent work breaks. Limit the amount of exposure per day.

If you experience any of the symptoms of this condition, immediately discontinue use and see your physician.

WARNING

Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

KNOW YOUR PRODUCT

On/off trigger
Cord hook
Power cord retainer
Edging button
Spool cover
Spool
Cut-off blade
Cutting line
Safety guard
Lower tube
Upper tube
Front handle
Rear handle

SYMBOLS ON THE PRODUCT

Read and understand all instructions before operating the product, follow all warnings and safety instructions.
Wear eye protection.
Wear hearing protection.
Do not use metal blade(s) on the product.
Do not expose to rain or damp condition.
Remove plug from the mains immediately before maintenance or if cable is damaged, cut or entangled.
Beware of thrown or flying objects. Keep all bystanders, especially children and pets, at least 15m away from the operating area.
Keep hands away from blades.
Class II tool, double insulation.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Conforms to all regulatory standards in the country in the EU where the product is purchased.
EurAsian Conformity Mark
Ukrainian mark of conformity
Guaranteed sound power level is 96 dB.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

DANGER

Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury

WARNING

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

CAUTION

Without safety alert symbol
Indicates a situation that may result in property damage.

SYMBOLS IN THIS MANUAL

Connect to power outlet.
Disconnect from power outlet.
Parts or accessories sold separately
Note
Warning

Product specifications

Electric lawn trimmer/ edge trimmer
Model
Rated power
Rated voltage
No-load speed
Cutting line diameter
Cutting capacity
Maximum vibration level (in accordance with EN 50636-2-91 Annex BB)
Uncertainty of measurement
Noise emission level
Maximum A-weighted sound pressure level at the operator’s position (in accordance with EN 50636-2-91 Annex CC)
Uncertainty of measurement
Maximum A-weighted sound power level (in accordance with 2000/14/ EC)
Uncertainty of measurement
Guaranteed A-weighted emission sound power level (in accordance with 2000/14/EC)

Replacement parts

Model

1.2 mm complete spool
1.2 mm spool (3 pcs)
1.2 mm spool (3 pcs)

GUARANTEE

In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.

The guarantee period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data which are required to enter online and they have to accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty. Your statutory rights remain unaffected.
The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to
• any damage to the product that is the result of improper maintenance
• any product that has been altered or modified
• any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
• any damage caused by non-observance of the instruction manual
• any non CE product
• any product which has been attempted to be repaired by an nonqualified professional or without prior authorization by Techtronic Industries
• any product connected to improper power supply (amps, voltage, frequency)
• any product used with inappropriate fuel mixture (fuel, oil, percentage of oil)
• any damage caused by external influences (chemical, physical, shocks) or foreign substances
• normal wear and tear of spare parts
• inappropriate use, overloading of the tool
• use of non-approved accessories or parts
• carburettor after 6 months, carburettor adjustments after 6 months
• components (parts and accessories) subject to natural wear and tear, including but not limited to bump knobs, drive belts, clutch, blades of hedge trimmers or lawn mowers, harness, cable throttle, carbon brushes, power cord, tines, felt washers, hitch pins, blower fans, blower and vacuum tubes, vacuum bag and straps, guide bars, saw chains, hoses, connector fittings, spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines, spark plugs, air filters, gas filters, mulching blades, etc
For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will have to be paid by the sender.
This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.