poly 1354-68669-001 RealPresence Group Series Media Center Installation Guide
- June 9, 2024
- Poly
Table of Contents
1354-68669-001 Real Presence Group Series Media Center
Installation Guide
1354-68669-001 Real Presence Group Series Media Center
Polycom Real Presence Group Series Media Center with 65 Inch Dual Displays
This supplement describes how to attach 65 inch dual displays on the Polycom
Real Presence Group Series Media Center. Follow the instructions in Setting Up
the Polycom Real Presence Group Series Media Center, 1725-08510-00X, and use
this supplement to replace the steps to install the displays.
Single 55/65 inch Lower Display Rail, 1354-67626-002
(2) Dual 65 inch Lower Display Rail Extension,
1354-68667-002
Dual 65 inch Center Top
Display Rail, 1354-68669-001
(2) Dual 65 inch Upper Display Rail Extension,
1354-68671-001
(4) Display Mounting Bracket Assembly 2342-67629-001
(4) M8 x 20 Button Head Cap Screw 1601-52713-001
(4) M8 Hex Flange Nut 1600-52845-001
(4) M10 x 25 Flanged Socket Head Cap Screw
1601-67617-002
M8 Wrench
1102-68064-001
For more information about the components of the Real Presence Group Series Media Center, refer to the documentation at http://support.polycom.com/PolycomService/support/us/support/video/group_series/group_packaged_solutions.html.
The Media Center components are heavy. Polycom recommends that two people perform the installation.
5a Install the lower display rail by aligning the holes in the display rail with the holes in the vertical supports. Attach with four M10 x 25 flanged socket head cap screws. Do not fully tighten.
5b Install a lower display rail extension to each side of the lower
display rail using two M8 x 20 button head cap screws and two M8 hex nuts per
side. Ensure the edge of the rail extension is 3.97 inches from the inner cut
edge of the bottom display rail. Tighten using the supplied M8 wrench.
6a Attach an upper display rail extension to each end of the center top
display rail using two M10 x 25 flanged socket head cap screws per extension.
6b Install the upper display rail assembly by aligning the holes in the
display rail with the holes in the vertical supports. Attach with two M10 x 25
flanged socket head cap screws per vertical support. Do not fully
tighten.
Attach the rear panel by inserting the two tabs at the bottom of the door into
the slots in the base. This serves as an alignment tool to ensure the frame is
properly aligned before tightening all bolts. Using the L-key, tighten the
socket head cap screws at the bottom of the base, the lower display rail, and
the upper display rail. Remove the rear panel.
On the back side, install a handle on both ends of the bottom display
rail.
Install the display mount brackets on the display. For the LG and Sampo 65
inch (PMQ65ML) display, position the display mounting bracket using the sixth
hole from the top with the top mounting hole on the display. The bottom hole
on the display is the seventh hole up from the bottom of the bracket.
For the Sampo 55 inch and 65 inch (PME65MA) display, position the third hole
down from the top of the display bracket with the third hole down from the top
of the display. The bottom hole on the display lines up with the fifth hole
up from the bottom of the display bracket.
Install the supplied 1/4-20 x 3.5 inch socket head cap screws at the top of
each display bracket. Leave the screws adjusted up before mounting the display
to the top rail.
Repeat with the second display.
LG 65 inch and Sampo 65 (PMQ65ML) inch Display
Sampo 55 inch and 65 inch (PME65MA) Display 
With the assistance of another person, lift the display and position the
display bracket hooks above the edge of the upper horizontal display rail on
the Media Center. Carefully lower the display onto the rail, ensuring the
hooks are fully engaged with the rail and that the outer most bracket is
positioned within the safety tab on the outer rail end (1). Repeat with the
second display.
Adjust the leveler screws as needed to help eliminate any gap between the two
displays when they are tightly abutted (2).
Center the displays on the Media Center. Insert one M6 x 16 flanged button
head screw into each outer display bracket to lock the displays.
Power Rating:
Voltage rating: 100-240 VAC, 50/60Hz
Maximum power consumption (configured with Group Series 500 codec and
EagleEye IV camera under full load operating conditions):
651.4W with Sampo (PME65MA) display
591.4W with Sampo (PMQ65ML) display
651.4W with LG display
Approximate system weight (including displays, codec, camera, and sound
system):
715 lbs. with Sampo (PME65MA) display
613 lbs. with Sampo (PMQ65ML) display
555 lbs. with LG display
Regulatory Notices:
- This equipment is intended for indoor use only.
- Only use this equipment with the displays supplied by Polycom.
- Do not use a power cord that is damaged. This could cause fire or electric shock. Contact the manufacturer for a replacement cord, if necessary.
- Only use a power cord which is appropriately rated and approved relevant to the country of use.
- This equipment should be used only on even surfaces.
- When moving or positioning the system, only use the handles located at the bottom of the display rail at the rear of the unit.
- This equipment has lockable wheels which should be applied while the cart is stationary.
- When connecting to the mains supply, connect only to an earthed supply outlet which is installed near the equipment and is easily accessible.
- Keep ventilation openings free from any obstructions.
- The ambient operating temperature rating of this equipment is 0 – 40ºC and should not be exceeded.
- Do not immerse the system in any liquid or place any liquids on it.
- Do not spray liquids directly onto the system when cleaning. Always apply the liquid first to a static-free cloth.
- For further information concerning the individual components of this equipment, please refer to the respective product literature.
- For support or service, please contact your Poly distributor or go to the Poly Online Support Center at support.polycom.com/content/support.html.
© 2021 Plantronics, Inc. All rights reserved.
Poly, the propeller design, and the Poly logo are trademarks of Plantronics,
Inc.
The Bluetooth trademark is owned by Bluetooth SIG,
Inc. and any use of the mark by Plantronics, Inc. is under license.
All other trademarks are the property of their respective owners.
1725-68117-003A
Documents / Resources
| poly
1354-68669-001 RealPresence Group Series Media
Center
[pdf] Installation Guide
1354-68669-001 RealPresence Group Series Media Center, 1354-68669-001,
RealPresence Group Series Media Center, Media Center
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>