BN thermic PH 450W Pew Heater Brown Instructions
- June 9, 2024
- BN Thermic
Table of Contents
BN thermic PH 450W Pew Heater Brown Instructions
1. SAFETY INSTRUCTIONS
1.1 ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following: You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, socke ts and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. If in any doubt consult a qualified electrician. You must also read and understand the following instructions concerning electrical safety.
1.1.1 The Health & Safety at Work Act 1974 makes owners of electrical
appliances responsible for the safe condition of those appliances and the
safety of the appliance operators. If in any doubt about electrical safety,
contact a qualified electrician.
1.1.2 Ensure that the insulation of all the cables on the appliance is safe
before connecting it to the power supply.
1.1.3 Ensure that the cables are always protected against short circuit and
overload.
1.1.4 Regularly inspect the power supply cables and plugs etc. for wear or
damage and check all connections to ensure that none are loose.
1.1.5 Important: Ensure that the voltage marked on the appliance matches the
power supply to be used and that a correctly rated fuse is fitted.
1.1.6 Installation should always be carried out by a qualified electrician in
accordance with current electrical regulation, protected by a suitably rated
isolator and fuse or mcb.
1.1.7 DO NOT use worn or damaged cables, plugs or connectors. Immediately have
any faulty item repaired or replaced by a qualified electrician.
1.1.8 Use of an extension cord with this product is not recommended.
1.2 GENERAL SAFETY INSTRUCTIONS
✓ Remove all packaging and store it away from children, check the package and
heater for visible damage or tampering.
✓ Familiarise yourself with the applications and limitations of the heater.
✓ Ensure the heater is in good order and condition both physically and
electrically before use. If in any doubt do not use the unit and contact an
electrician.
✓ Only use recommended attachments and parts. To use unauthorised parts may be
dangerous and will invalidate your warranty.
✓ Disconnect from mains and allow to cool before attempting any cleaning.
X DO NOT use in hazardous areas.
X DO NOT cover the heater or restrict free circulation of air around it.
X DO NOT subject the heater to exposure to water.
X DO NOT locate the heater below the power outlet.
X DO NOT install this heater against combustible low-density fibre board
surfaces.
X DO NOT disassemble the heater for any reason. This heater must be checked by
qualified personnel only.
X DO NOT use this heater to perform a task for which it has not been designed.
X DO NOT use this heater outdoors.
❑ WARNING! This heater is not equipped with a device to control the room
temperature. Do not use this heater in a small room if it is occupied by
people not capable of leaving the room on their own, unless constant
supervision is provided.
❑ WARNING! Ensure there is no possibility of inflammable materials coming into
contact with the heater.
2. INTRODUCTION & SPECIFICATION
This heater produces a totally dry heat, no condensation, no gas, no fumes and no smell. It reaches maximum heat output within a few minutes of being turned on. The heater is designed to be mounted at floor level. Typical application is Pew Heating in Churches although they can also be very effective if used for room or office heating.
3. MOUNTING / INSTALLATION
❑ IMPORTANT! Ensure that the mounting surface is capable of supporting the
weight of the heater.
❑ IMPORTANT! The heater should only be mounted horizontally.
❑ IMPORTANT! Leave a minimum of 125mm (5”) between the top of the heater and
the bottom of the seat.
3.1 ELECTRICAL CONNECTION
❑ IMPORTANT! Ensure you have read the Safety instructions and you are a
suitably qualified electrician before continuing.
❑ IMPORTANT! The voltage marked on the heater must correspond to the supply
voltage.
❑ IMPORTANT! To comply with the I.E.E. Wiring Regulations, the appliance must
be earthed; the supply circuit must be adequate for the input of the
appliance, and the circuit protected by a suitable fuse. If the heater is to
be connected to a fixed electricity supply, a suitable termination must be
provided adjacent to the final position of the appliance. In this instance,
such a termination must be a double pole switch with a contact separation of
at least 3mm in all poles.
❑ You may wish to mount the heater in position first if so read section 3.2
Pew Mounting
3.1.1 The terminal connection block is located under the cover on the left
hand end of the heater.
3.1.2 When removing the cover remove the earth cable that is connected to the
right hand end of the heater by carefully pulling off the spade connector.
Remember to reconnect this earth wire when replacing the cover.
3.1.3 20mm Knockouts are provided both ends of the heater.
3.1.4 3 Core mains cable may be run along the bottom on the inside of the
heater as long as it is suitable for 80⁰C temperatures. T his can enable cable
entry from the right hand side should you wish or when you may want to daisy
chain the heaters. Please ensure you do not exceed the total loading of the
mains cable.
3.1.5 Connect the Earth wire normally GREEN/YELLOW to the earth terminal
marked “E”.
Connect the Live wire normally BROWN to the live terminal marked “L”.
Connect the Neutral wire normally BLUE neutral wire to the neutral terminal
marked “N”.
3.1.6 After wiring, check that there are no bare wires, that all wires have
been correctly connected and then replace the electrical cover ensuring you
reconnect the earth wire on the right hand end. Screw the cover in place.
3.2 PEW MOUNTING.
3.2.1 The Heater must be mounted horizontally using 4 screws (not supplied).
3.2.2 We recommend leaving a minimum of 125mm (5”) between the top of the
heater and the bottom of the seat. Optimum gap +150mm. If a back board is not
present use the hanging brackets (optional extra).
3.2.3 The mounting holes are behind the front cover. Please remember to remove
the earth cable and then reconnect it when taking on and off the cover.
3.2.4 Before drilling any holes ensure there are no wires or pipes in the area
you are fixing the heater.
3.2.5 After tightening the 4 screws loosen each by one half a turn to allow
for expansion of the metal case.
3.3 FLOOR MOUNTING (using PHF brackets)
3.3.1 Screw the brackets to the floor ensuring that they have been set at the
correct pitch to line up with the mounting holes in the back of the heater.
3.2.2 The mounting holes are behind the front cover. Please remember to remove
the earth cable and then reconnect it when taking on and off the cover.
3.3.3 Using the screws supplied attach the heater to the brackets set level
and secure in place.
3.3.4 After tightening the 4 screws loosen each by one quarter of a turn to
allow for expansion of the metal case.
3.4 HANG MOUNTING (using PHB brackets)
3.4.1 Screw the brackets to underneath of the Pew ensuring that they have been
set at the correct pitch to line up with the mounting holes in the back of the
heater.
3.4.2 The mounting holes are behind the front cover. Please remember to remove
the earth cable and then reconnect it when taking on and off the cover.
3.4.3 Using the screws supplied attach the heater to the brackets set level
and secure in place.
3.4.4 After tightening the 4 screws loosen each by one quarter of a turn to
allow for expansion of the metal case.
4. OPERATION
When energised the heater will provide its maximum output within a few minutes. Should the unit register an abnormal rise in temperature the over temperature safety devices will shut the heater down. In these circumstances isolate the heater and ensure that there is no obstruction to the air inlet or outlet. If the over temperature safety device operates repeatedly isolate the heater and consult a qualified electrician.
5. MAINTENANCE
BN Thermic pew heaters are manufactured, assembled and tested in the UK and are non-user serviceable. They are designed to operate for many years, problem free. Maintenance is limited to the keeping of both inlet and exhaust areas free from any accumulation of dust and other foreign materials. This is especially important immediately before a heating season. Any dust build-up can be loosened with a brush and a vacuum cleaner applied to the airways to ensure complete removal of dust materials. An unusual odour may be noted on the initial turn-on period as any dust particles may have been disturbed and will be burnt off from the element. Note: Before examining or carrying out any maintenance ensure the heater has cooled down and is disconnected from the mains supply.
WEEE REGULATIONS: This appliance bears the symbol of the crossed waste bin. This indicates that, at the end of its useful life, it must not be disposed of as domestic waste, but must be taken to a collection centre for waste electrical and electronic equipment. It is the user’s responsibility to dispose of this appliance through the appropriate channels. Failure to do so may incur penalties established by laws governing waste disposal.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Your BN Thermic product is guaranteed for one year from date of purchase. We will repair or replace at our discretion any part found to be defective. We cannot assume any consequential liability. This guarantee in no way prejudices your rights under common law and is offered as an addition to consumer liability rights.
REGISTER: Activate your warranty by registering online at www.bnthermic.co.uk and retain this installation data for future reference.
BN Thermic Ltd, 34 Stephenson Way, Crawley, RH10 1TN Tel: +44 (0) 1293 547361 sales@bnthermic.co.uk www.bnthermic.co.uk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>