AQUADART Venturi 6 AQ9359S-Swiftseal Single Bath Screen Instruction Manual
- June 9, 2024
- AQUADART
Table of Contents
AQUADART Venturi 6 AQ9359S-Swiftseal Single Bath Screen
Tools Required
IMPORTANT
This product should be installed by a suitably qualified and proficient person. The fitting instructions should be followed carefully to ensure a proper and safe installation. Failure to follow these instructions could result in future injury. These instructions and list of parts assume that installation is done against solid/tiled walls. Please check this product for damage prior to starting the installation. No claims can be made after the product has been fitted.
PLEASE NOTE: The minimum and maximum adjustment sizes noted on the product brochures are based on perfectly plumb walls and trays.
USE SAFETY EYE-WEAR WHEN DRILLING
COMPONENTS AND BOX CONTENTS
| No. | Description | Qty | No. | Description | Qty |
|---|---|---|---|---|---|
| 1 | Wall Profile | 1 | 11 | Arm Rail | 1 |
| 2 | Wall Plug | 3 | 12 | Glass | 1 |
| 3 | Bolt | 2 | 13 | Fixing Screw M6x12 | 1 |
| 4 | Fixing Screw ST 4×30 | 3 | 14 | Cover Cap(For Rail Holder) | 1 |
| 5 | Cover Cap | 3 | 15 | Rail Holder Fixing | 1 |
| 6 | Fixing Screw ST 4×10 | 3 | 16 | Washers | 2 |
| 7 | Cover Cup | 3 | 17 | Bottom Rail Holder | 2(L/R) |
| 8 | Washer A | 1 | 18 | End Cap | 2(L/R) |
| 9 | Washer B | 1 | |||
| 10 | Bubble Seal(For Arm Rail) | 1 |
Fixing Kit
INSTALLATION INSTRUCTIONS
- Step 1: Position the wall profile (No 1 ) onto the bath , approximately 12-15mm from the outside bath edge , ensuring that the side with the pre-drilled holes are fa cing outwards from the bath ( Diagram A).
- Step 2: Level the profile with a spirit level, then mark the position using a pencil through the 3 pre-drilled screw holes in the wall profile,drill the marked points using a 6mm masonry drill bit. Once this is done insert 3 wall plugs(No.2) (Diagram B).
-
* **NOTE:** You may find it easier to mark and drill the wall if you apply masking tape to it first.
-
- Step 3: Secure the wall profile using 3 x ST4X30 screws (No.4) (Diagram C).
- Step 4: Inset the bubble seal(No.10) onto the arm rail profile(No.11). (Diagram D)
- Step 5: Drop a little bit of silicone sealant into the arm rail profile (No.11) then press the CORRE CT handed end cap (No.18) into the arm rail profile(No.11) (Diagram E)
- Step 6: Fit the washers(No.8,No.9 ) onto the arm rail profile(No.11) (Diagram F).
- Step 7: Fit the assembled arm rail above onto the wall profile then insert the bolt (No.3) to secure the arm rail profile. (Diagram G).
- Step 8: Push the bath screen assembly onto the wall profile (Diagram H).
- Step 9: Drill 3 equally spaced holes with a 3mm drill bit through the wall profile into the frame(Diagram I)
- Step 10: Fix the bath screen assembly to the wall profile using the screws ST4 x10 (No.6). (Diagram J)
- Step 11: Press the cover cap(No.7) into the hole at the top of the wall profile(Diagram K)
- Note: Follow the steps below to assemble the bathscreen into a right hand version. The bathscreen is pre-assembled in left hand format”. Loosen the bottom rail holder piece from the bath screen assembly ( Diagram L ) and attach the right handed bottom rail holder ( Diagram M ).
- Step 12: S ilicone the outside of the wall post as shown(M).
- Step 13: S ilicone the inside of the wall post as shown(N).
To open the bath screen please follow the steps as below
- Press the bottom rail profile with a soft downward motion to release it from the rail holder.(Diagram O）
- Lift the bottom rail to rotate it into the wall profile channel (Diagram P), then you can open/close the bath screen.
AFTERCARE
Cleaning Instructions
It is important to clean your Aquadart shower enclosure after every use. Please wipe down all glass and metal parts with a clean soft cloth. Ensure that all residual water on the glass is removed after every use.
Usage
For reliable, watertight performance from your Aquadart enclosure your shower head should not be positioned so that the shower sprays directly onto the enclosure door. Failure to comply with this may cause the shower to leak. Outward opening doors may cause water to drip onto the floor, please ensure that the floor covering immediately outside the enclosure will not be affected by water.
This product has been treated with Clean & Clear™ easy clean glass treatment, a protective barrier that creates a ‘non-stick’ surface on your glass, helping to resist lime scale build up and water spots. For further information on Clean & Clear™ please visit www.aquadart.co.uk
Aftercare
Clean & Clear™ glass can be cleaned with any suitable nonabrasive glass cleaner- with PH value of between 3- 11; the coating will not be damaged. Avoid surfactants and heavily perfumed products. Vinegar and water-based products are very effective. Do not use abrasive scrubbing cleaners or equipment for cleaning.
Warranty
Limited 5-year Warranty for Clean & Clear™ treatment: To guarantee treated surfaces will remain more repellent than untreated glass for 5 years from start of use, as long as basic manufacturer maintenance recommendations are followed and no harsh or abrasive cleaners are used.
AQUADART
- Riverside Business Park, Royd Ings Avenue, Keighley, West Yorkshire, BD21 4AF
- For technical/aftersales queries, please visit our website: www.aguadart.co.uk
- or Sales Tel: 01535 613830
- Technical: 01535 613830
- Fax: 01535 613831
References
- April Products - Supreme Quality Shower Enclosures, Baths and Bathroom Products
- Aquadart Shower Enclosures - an inspiring collection in luxury showering solutions | Aquadart
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>