Interface 3A Series Multi Axis Load Cells Instruction Manual

June 9, 2024
Interface

Interface 3A Series Multi Axis Load Cells Instruction Manual
Interface 3A Series Multi Axis Load Cells

INSTALLATION INFORMATION

  1. Interface model 3A Series multi-axis load cells must be mounted on a surface that is flat and rigid enough so as to not deform appreciably under load.
  2. Fasteners should be Grade 8.8 for 3A60 thru 3A160 and Grade 10.9 for 3A300 and 3A400
  3. Sensors should be mounted using the recommended screws and mounting torques in the table below.
  4. Dowel pins should be used at all mounting surfaces.
  5. For 3A300 and 3A400 at least two dowel pins should be used on the live end. Up to 5 can be used.
  6. For sensors 500N and above, a thin coating of Loctite 638 or similar is recommended on the three mounting surfaces to prevent slippage.
  7. Mounting fixtures and plates may only contact the sensor at the indicated mounting surfaces.

MOUNTING DETAILS

| Model| Rated load/ Capacity| Dimensions| Material| Measuring platform / Live End| Stator / Dead End
---|---|---|---|---|---|---
Thread| Tightening Torque (Nm)| Cylinder pin Hole

(mm)

| Thread / Cylindered Screw| Tightening Torque (Nm)| Cylinder pin Hole

(mm)

| 3A40| ±2N

±10N

±20N

±50N

| 40 mm x
40 mm x
20 mm| aluminum alloy| internal thread 4x M3x0.5

depth 8 mm

| 1| no| internal thread 4x M3x0.5

depth 8 mm

| 1| no
| 3A60A| ±10N
±20N
±50N
±100N| 60 mm x
60 mm x
25 mm| aluminum alloy| internal thread 4x M3x0.5
depth 12 mm| 1| 2 x Ø2 E7
depth 12 mm| 2 x DIN EN ISO
4762 M4х0.7 6.8| 2| 2 x Ø3 E7
depth 5 mm
±200N

±500N

| stainless steel| internal thread 4x M3x0.5
depth 12 mm| 1| 2 x Ø2 E7
depth 12 mm| 2 x DIN EN ISO
4762 M4х0.7 6.8| 2| 2 x Ø3 E7
depth 5 mm
| 3A120| ±50N
±100N
±200N
±500N
±1000N| 120 mm x
120 mm x
30 mm| aluminum alloy| Internal thread 4x M6x1 Depth 12 mm| 10| 2 x Ø5 E7
Depth 12 mm| 4 x DIN EN ISO
4762 M6х1 6.8| 10| 2 x Ø5 E7
depth 3 mm
±1kN

±2kN

±5kN

| stainless steel| internal thread 4x M6x1 Depth 12 mm| 15| 2 x Ø5 E7
Depth 12 mm| 4 x DIN EN ISO
4762 M6х1 10.9| 15| 2 x Ø5 E7
depth 3 mm
| 3A160|

±2kN
±5kN

| 160 mm x

160 mm x

66 mm

| tool steel| internal thread 4x M10x1.5

depth 15 mm

| 50| 2 x Ø8 H7

depth 15 mm

| 4 x DIN EN ISO

4762 M12х1.75

10.9

| 80| 2 x Ø8 H7

depth 5 mm

±10kN

±20kN

±50kN

| tool steel| internal thread 4x M10x1.5

depth 15 mm

| 60|

2 x Ø8 H7

depth 15 mm

| 4 x DIN EN ISO

4762 M12х1.75

10.9

| 100|

2 x Ø8 H7

depth 5 mm

Mounting instruction| 3A300| ±50kN| 300 mm x

300 mm x

100 mm

| tool steel| internal thread 4x M24x3| 500|

5x Ø25 H7

| 4 x DIN EN ISO

4762 M24х3

10.9

| 500| 2 x Ø25 H7

depth 40 mm

±100kN

±200kN

|

800

| 800
| 3A400| ±500kN| 400 mm x

400 mm x

100 mm

| tool steel| internal thread 4x M30x3.5| 1800| 5x Ø30 E7| 4 x DIN EN ISO

4762 M30х3.5

10.9

| 1800| 2 x Ø30 E7

depth 40 mm

Mounting surface

Interface Inc.

  • 7401 East Butherus Drive
  • Scottsdale, Arizona 85260 USA

Support

Phone: 480.948.5555
Fax: 480.948.1924
www.interfaceforce.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Interface User Manuals

Related Manuals