BCS Automotive Interface Solutions s r o WSPC2 Wireless Charger User Manual
- May 15, 2024
- BCS Automotive Interface Solutions s r o
Table of Contents
BCS Automotive Interface Solutions s r o WSPC2 Wireless Charger
Product Information
Specifications
- Product: Wireless Charger
- Compatibility: Qi-enabled smartphones
- Power Delivery: Up to 15W
- Additional Feature: NFC reader for NFC card protection
- RF Warning: FCC compliant with a minimum distance of 20cm between the device and the body
Product Usage Instructions
- Ensure your smartphone is Qi-enabled for wireless charging.
- If your phone case is metal, remove the phone from the case before placing it on the charger.
- Place your smartphone on the rubber mat located above the wireless charger.
- Wait for the charging process to start; ensure proper alignment for efficient charging.
- To protect an NFC card, make sure an NFC reader is present in the wireless charging module.
- Keep a minimum distance of 20cm between the wireless charger and your body for RF compliance.
Frequently Asked Questions (FAQ)
-
Q: My phone is not charging on the wireless charger. What could be the issue?
A: If your phone case is metal, it may interfere with wireless charging. Remove the phone from the case and try again. Ensure proper alignment on the charger. -
Q: How can I protect an NFC card while charging my smartphone?
A: Make sure an NFC reader is integrated into the wireless charging module. When an NFC card is detected, charging will stop to protect the card. -
Q: Is it safe to use the wireless charger close to my body?
A: The wireless charger complies with FCC radiation exposure limits. Maintain a minimum distance of 20cm between the device and your body for safe operation.
Introduction
This wireless charger can charge your Qi‐enabled smartphone. Just simply place your smartphone on the rubber mat above the wireless charger. The wireless charger supports up to 1 5 W power delivery.
NOTE:
The wireless charger may not work if your phone case is metal. Take the phone
out of the case and place the phone on the charger.
Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
Radiation Exposure Statement:
This equipment complies with radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
The frequency band in which the radio equipment operates is 127.58-128.01 kHz. 13.56Mhz
Specification
- Model name: WSPC2
- Manufacturer: BCS Automotive Interface Solutions, s.r.o.
- Adress: Jana Nohy 2048 256 01 Benesov
- Max. Output: 1 5 W
- Input: 2 4 V DC @ 1.5A
- Operating Temperature: ‐40℃~85℃
- Storage Temperature: ‐40℃~105℃
The Wireless Power Consortium (WPC) recommends adding an NFC reader to the wireless charging module. Once the NFC card is detected, it will stop charging to protect the NFC card.
FCC Caution
15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.21 Changes or modification warning.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, under part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used by the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Mobile devices:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>