LGSBWAC23 802.11a-b-g-n-ac + Bluetooth Combo Module User Manual
- June 9, 2024
- LG
Table of Contents
SBWAC23 802.11a-b-g-n-ac + Bluetooth Combo Module
User Manual
LGSBWAC23 802.11a-b-g-n-ac + Bluetooth Combo Module
The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek.
REG. DATE : 2022.06.24| USER MANUAL
MODEL NAME : ETWCFRBC01 (LGIT)LGSBWAC23 (LGE)| REV.NO : 1.0
---|---|---
REV. DATE : 2022.06.24| PAGE : 1 / 7
Features
ETWCFRBC01 is the small size and low power module for IEEE 802.11ac wireless LAN & BT5.0 + HS. ETWCFRBC01 is based on Realtek RTL8822CU solution.
-
IEEE 802.11 a/b/g/n/ac Dual Band
-
Bluetooth 5.0 + HS, BLE
-
Size : 48.4 x 30.0 x 7.7 mm
-
Two stream spatial multiplexing up to 300Mbps (802.11n) / 866.7Mbps (802.11ac)
-
Use on-chip OTP (One-Time Programmable)
-
Host Interface : USB2.0 (WLAN & BT)
– This model is using the common USB2.0 to control WLAN and BT -
Security : 802.11e 802.11i (WPA, WPA2), WAPI
-
WAPI, WEP, WPA, WPA2, WMM, AES, TKIP, CKP
-
Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB
Block Diagram
Absolute Maximum Ratings
Caution : The specifications in Table 1 define levels at which permanent
damage to the device can occur. Function operation is not guaranteed under
these conditions.
Operating at absolute maximum conditions for extend periods can adversely
affect the long-term reliability of the device.
Parameter | Min | Max | Unit |
---|---|---|---|
Storage Temperature | -20 | 80 | ℃ |
Storage Humidity (40℃) | – | 90 | % |
< Table 1 > . Other conditions
-
Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained.
Also, avoid exposure to moisture. -
Store the modules where the temperature and relative humidity do not exceed 5 to 40℃ and 20 to 60%.
-
Assemble the modules within 6 months. Check the soldering ability in case of 6 months over.
Operating Conditions
Parameter | Min | Typ | Max | Unit |
---|---|---|---|---|
Ambient Temperature | 0 | 60 | ℃ | |
Ambient Humidity (40℃) | 85 | % | ||
Supply Voltage | 3.135 | 3.3 | 3.6 | Vdc |
Standard Test Conditions
The Test for electrical specification shall be performed under the following
condition Otherwise this following conditions, not guaranteed this
performance.
5-1. Ambient condition
Temperature | 25 ± 5℃ |
---|---|
Humidity | 65 ± 5% |
5-2. Power supply voltages
Input power | Supply Voltage |
---|---|
VDD_3.3V | 3.135 ~ 3.6V |
5-3. Current consumption
Current Consumption | Min. | Typ. | Max. | Unit |
---|---|---|---|---|
TX Mode ( 11ac/80MHz) | 1200 | mA | ||
Idle and Associated state | 320 | |||
Radio disabled state | 100 |
Note 1. This figure is the RMS(root mean square) value.
5-4. ESD Information
Human Body Model (HBM) | Min. | Max. | Unit |
---|---|---|---|
Contact | ±4 | kV | |
Air | ±15 |
Note 1. IEC 61000-4-2 (150pF, 330R)
Note 2. Test condition : After 8-pin USB Cable connect to module,
progress ESD test.
Pin Description
Pin N | Pin Name | I/O | Pin Description |
---|---|---|---|
1 | VCC | I | VDD 3.3V |
2 | D- | I/O | USB Communication signal (USB_DN) |
3 | D+ | I/O | USB Communication signal (USB_DP) |
4 | GND | – | GND |
5 | WOWL | O | Wake On WLAN |
6 | VCC | I | VDD 3.3V |
7 | NC | – | No connection |
8 | GND | – | GND |
9 | RESET | I | RESET |
10 | WOBLE | O | Host wake up. (Signal from Wi-Fi module to the host) |
11 | GND | – | GND |
12 | VCC | – | VDD 3.3V |
Mechanical Characteristics
- Outline view**
Item| Test Conditions**
---|---
Assembly| No defects of wiring, soldering and assembling
Appearance| No dirt, rust, corrosion or foreign material - Appearance structure****
Item| Test Conditions
---|---
Dimension| As assembly drawing
Mounting| As assembly drawing
Weight| 6g
Outline Drawing
Regulatory Statement (FCC)
-
Part 15.19 Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Part 15.105 Statement (Class B)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help. -
Part 15.21 Statement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device must not be co-located or operating in conjunction with any other antenna or transmitter. -
Responsible Party Information (Supplier’s Declaration of Conformity) LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs New Jersey, United States, 07632
Regulatory Statement (FCC)
Regulatory notice to host manufacturer according to KDB 996369 D03 OEM
Manual v01
List of applicable FCC rules
This module has been granted modular approval as below listed FCC rule parts.
- FCC Rule parts 15C(15.247,15.407)
Summarize the specific operational use conditions
The OEM integrator should use equivalent antennas which is the same type and
equal or less gain then an antenna listed in this instruction manual.
RF exposure considerations
The module has been certified for integration into products only by OEM
integrators under the following condition:
- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
- Mobile use
As long as the three conditions above are met, further transmitter testing
will not be required.
OEM integrators should provide the minimum separation distance to end users in
their end-product manuals.
Regulatory Statement (FCC)
- Antennas list
This module is certified with the following integrated antenna.
-Type: Metal Press Antenna
-Max. peak Antenna gain
- ANT 1: -0.94 dBi (2412-2472MHz) / 1.50 dBi (UNII-1) / 1.50 dBi(UNII-2A) / 1.48 dBi(UNII-2C) / 1.50 dBi(UNII-3)
- ANT 2: -1.68 dBi (2412-2472MHz) / 1.43 dBi (UNII-1) / 1.50 dBi(UNII-2A) / 1.46 dBi(UNII-2C) / 1.49 dBi(UNII-3)
- BT Ant: 1.12 dBi (2402-2480 MHz)
Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.
-
Label and compliance information
End Product Labeling
The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: -
Contains FCC ID: BEJLGSBWAC23
-
Contains IC: 2703H-LGSBWAC23
-
Information on test modes and additional testing requirements OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter in the host, etc.).
-
Additional testing, Part 15 Subpart B disclaimer
The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device.
Regulatory Statement (ISED)
RSS-GEN, Sec. 7.1.3–(licence-exempt radio apparatus)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure
The antenna (or antennas) must be installed so as to maintain at all times a
distance minimum of at least 20 cm between the radiation source (antenna) and
any individual. This device may not be installed or used in conjunction with
any other antenna or transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>