PS-206-SS Permasteel 80QT Cooler User Guide
- June 9, 2024
- PermaSteel
Table of Contents
Permasteel 80QT Cooler
Use & Care Guide
Model number: PS-206-SS
Thank you for purchasing your new patio cooler from Permasteel
We hope you enjoy your product.
If you have any questions, please call us
1-888-287-0735
or visit www.permasteel.life
Important Information
Thank you for your purchase of our Patio Cooler.
We sincerely hope you will enjoy using our fine products.
- Please take time to read these instructions thoroughly and follow each step carefully for safe and easy operation.
- Please contact our customer service at 1-888-287-0735 if you have any questions.
- Please keep this manual for future reference.
CAUTION
- Hand tools only, use of power tools could damage product.
- Remove all components, hardware and toolsfrom box before assembly. Inventory and separate each of the hardware and components included.
- Please consider recycling all applicable packaging material.
Parts List
| Key | Description | Qty |
|---|---|---|
| A | Lid Knob | 2 |
| B | Lid | 1 |
| C | Body Handle (Long) | 1 |
| D | Body Handle (Short) | 1 |
| E | Body (Basin) | 1 |
| F | Bottle Opener | 1 |
| G | Bottle Cap Catcher | 1 |
| H | Leg | 4 |
| I | Bottom Shelf | 1 |
| J | Caster | 2 |
| K | Caster with Brake | 2 |
| AA | M6 x 16 Hex Bolt | 8 |
| BB | M6 x 16 Hex Socket Bolt | 14 |
| CC | M6 x 16 Bolt | 2 |
| DD | M5 x 35 Screw | 2 |
If you are missing any parts or have damaged parts, please call
1-888-287-0735 M-F 8:00-5:00
Pacific Time. For replacement, visit us at
www.permasteel.life
Hardware
The following hardware is provided in a poly bag.
M6x16mm Hex Bolt: 8 pcs|
---|---
M6X16mm Hex Socket Bolt: 14 pcs| 
M6x16mm Bolt: 2 pcs (Pre-installed on body)|
M5X35mm Screw: 2 pcs (Note: Attached to lid knobs)|
Tools Included:|
Tools
The following tools are required for assembly:
- Allen wrench (provided)
- Phillips screwdriver (not provided)
Assembly Instructions
Step 1
- Turn body (basin) upside down, place it on a clean, soft surface and attach 4 legs (H) to body (E) with (2) M6x16mm hex bolts (AA) for each leg, a total of 8 bolts.
Note: Do not fully tighten the bolts. Legs should be loose so that it can be aligned with the holes on the bottom shelf.
Step 2:
-
Attach the bottom shelf (I) to the legs (H).
-
Insert and thread casters (J) through the bottom panel holes into two legs on the same side.
-
Insert and thread casters (K) through the bottom panel holes into other two legs on the same side.
Note: Do not fully tighten the bolts. Legs and bottom shelf should be loose so that it can be aligned with the holes for the casters. -
Now, tighten all the bolts left loose from step 1.
Step 3
- Attach the body handles (C & D) to body (E) using (6) M6x16mm hex socket bolts (BB) for each handle, a total of 12 bolts, and fully tighten.
Step 4
- Attach the bottle opener (F) to body (E) using (2) M6x16mm hex socket bolts (BB) and fully tighten with the provided allen wrench.
- Attach the cap catcher (G) to body (E) by sliding it down over the 2 pre-installed bolts (CC).
Step 5
- Note: The lid knobs (A) are pre-attached to the lid (B) with (2) M5x35mm screws. They are upside down.
- Please remove the knobs using a Phillips head screwdriver and re-assemble them on the lid right-side up.
Care & Maintenance
Manufacturer recommends the following care & maintenance:
- Cooler must be drained of water and completely dried in and out with a soft-clean cloth after every use.
- When cooler is not in use for prolonged periods, it is recommended to store it in an enclosed dry place such as a storage shed or garage.
- During the season when cooler is frequently used, it is recommended to use a weather-proof cover to cover when not in use.
- It is recommended to clean the stainless steel surfaces with a good oily stainless cleaner after each use to protect & prolong the life & finish of the cooler.
- We strongly recommend not rolling the cooler on rough surfaces such as pavers when the cooler is loaded full with ice & drinks.
- For further care & maintenance tips or questions, please call customer service at 1-888-287-0735 or email us at [email protected] or visit us at www.permasteel.life
Limited Warranty
PERMASTEEL INC. Guarantees that this Product shall be free from defects in
workmanship and materials, for a period of 90 Days from the date of original
purchase. Our obligation under this warranty shall be limited to replacement
of parts during the warranty period. Our liability shall not extend beyond
replacement of parts.
This warranty excludes normal wear & tear such as paint loss, discoloration
and rust on the product and its parts or components, and any damage arising
from any of the following: negligent use or misuse of the Product, use
contrary to this User’s Manual, or alteration by anyone other than Permasteel
Inc.
All warranty coverage is void if this cooler is ever used for commercial or
rental purposes; this warranty is valid only in the USA.
This warranty period of 90 Days shall not be extended or renewed for the
repair or replacement of parts or compensation for the Product. If your
Product is defective or
otherwise requires service or parts, please call Permasteel Customer Service
at 1-888-287-0735, between 8:00 a.m. to
5:00 p.m. PST.
Email: [email protected] or visit us
at www.permasteel.life
Permasteel Inc. will ship parts free of charge for a period of 30 days from
the date of purchase. The consumer is responsible for shipping & handling and
processing of warranty claims after 30 days from the purchase date.
Proof of purchase, like purchase receipt, must accompany any service requests.
We hope you enjoy your product and we are always here for you:
Visit us at: www.permasteel.life
Customer Service: 1-888-287-0735
Email:[email protected]