Wanderera 634325 Double High Queen Premium Air Bed Instruction Manual

Wanderera 634325 Double High Queen Premium Air Bed Instruction Manual

PLEASE READ CAREFULLY TO ENSURE YOUR SAFETY

PLU: 634325 CODE: 30005A-SHZJ
DESCRIPTION: AIRBED DBL HIGH QUEEN PREM WANDERER

INFLATED DIMENSIONS
L203 x W158 x I-149cm
DEFLATED DIMENSIONS
L198 x W152cm Measured from top panel prior to first inflation from top seam to bottom seam and left seam to right seam.

INFLATED CONDITIONS
Air Bed dimensions measured in a 25°C controlled, indoors environment once the air bed is fully inflated at its firmest comfort level, using a manual hand pump. Due to the properties of PVC, this measurement is likely to vary based on your environment, inflating apparatus and desired level of mattress firmness. We allow a tolerance of +1- 4.0% of our air bed’s dimensions when inflated under our controlled conditions.

IMPORTANT SAFETY INFORMATION AND WARNINGS

1. Adult supervision required for inflation, deflation and maintenance. Follow all safety instructions to avoid serious injury.
2. This is not a toy. Please ensure that children are under adult supervision when using this product.
3. Remove all sharp objects from area where bed will be set up and used. Bed may puncture.
4. Do not step or jump on bed or use as a trampoline.
5. Place bed in a safe area before use, making sure that there are no sharp edges, steps drops or breakable items nearby. Use on flat surfaces only. Bed may tip over on uneven surfaces.

PVC STRETCH
PVC material naturally stretches when under pressure. You may find your airbed appears to have lost some air after a night’s sleep but this is not the case. During the first few uses, the PVC will stretch naturally until it reaches optimum level. When this occurs, simply top up with more air until you reach the desired level of support.

INFLATION
Place your rolled up bed on the floor or other surface free of obstructions or sharp objects. Open protective cap on valve. Use manual or powered pump with correct size adaptor. Turn pump off and replace valve cap when bed is fully inflated.

DEFLATION
Open valve cap, then roll the bed completely until all the air is expelled. When the bed is completely rolled flat replace the valve cap.

CARE & MAINTENANCE

1. Check the air level of the air bed occasionally. If more than one person is using the air bed at the same time, less air may be required for comfort. Experience will suggest the best air levels.
2. In case of the velour gets wet or dirty, clean it thoroughly with soap and water before letting it air dry. Do not use chemicals, scouring powder or any other abrasive.
3. Avoid exposing the air bed to extreme temperatures. Inflate at room temperature.
4. Avoid over-inflating the air bed.
5. Be careful of sharp objects that can damage the outer PVC material.

REPAIRING PIN-SIZED HOLES

1. Deflate the bed.
2. Apply repair glue (included in repair kit) to the tip of toothpick or pin and insert into the puncture.
3. Allow the glue to set; making sure the puncture is fully covered.
4. Apply a small amount of glue directly on top of the puncture.
5. Leave for at least four hours before re-inflating.

REPAIRING RIPS OR TEARS

1. After deflating the bed, cut a piece of patching material !included in repair kit) large enough to overlap the rip or tear.
2. Apply the glue to the damaged area and press on the patch. Add more glue as needed to the sides of the patch and apply pressure to ensure proper and flawless bonding to the material of the bed.
3. Leave for at least four hours before re-inflating.

PLU: 634325 CODE: 30005A-SHZJ
Manufactured and packaged for SRGS PTY LTD AUN 23 113 230 050 6 Coulthards Avenue Strathpine OLD 4500, Australia MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>