GAGGENAU DV061100 Vacuum Sealing Drawer Instruction Manual

: June 9, 2024
: Gaggenau

Table of Contents

Scope of delivery
Unit dimensions
Safety clearances
Safe installation
Instructions for the electrical connection
Tools
Preparing the appliance
Preparing the units
Installing the appliance
Preparing the furniture panel
Installing the furniture panel
Adjusting the furniture panel
Screwing the furniture panel in tightly
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DV061100 Vacuum Sealing Drawer
Instruction Manual

Scope of delivery

After unpacking all parts, check for any damage in transit and completeness of the delivery.

Appliance
Front panel
Tilt protection (2 pcs)
Wood screw for the tilt protection (4 pcs)
Oil filter
Power cord
Mounting bracket (2 pcs)
Installation aid for the mounting bracket
Wood screws for the angle bracket (4 pcs)
Decorative panel 10.5 mm (2 pcs)
Decorative panel 12.5 mm (2 pcs)
Metric screw (4 pcs)
Threaded sleeve (6 pcs)
Metric screw (6 pcs)
Concave washer (2 pcs)
Adhesive buffers
Double-sided adhesive tape (3 pcs)

Unit dimensions

You will find the dimensions of the appliance here

Safety clearances

Comply with the safety clearances for the appliance.
Installing the appliance under the worktop
If the worktop overlaps with the furniture cavity by too much, this may lead to collisions with the glass cover in the vacuum-sealing drawer. Note the maximum possible dimension.

Installation in the fitted unit
Note the safety clearances for installing in the fitted unit.

Safe installation

Follow these safety instructions when installing the appliance.
WARNING ‒ Risk of suffocation!
Children may put packaging material over their heads or wrap themselves up in it and suffocate.

Keep packaging material away from children.
Do not let children play with packaging material.

WARNING ‒ Risk of electric shock!
If the insulation of the power cord is damaged, this is dangerous.

Never let the power cord come into contact with hot appliance parts or heat sources.
Never let the power cord come into contact with sharp points or edges.
Never kink, crush or modify the power cord.

Instructions for the electrical connection

In order to safely connect the appliance to the electrical system, follow these instructions.

The appliance must only be connected to a protective contact socket that has been correctly installed.
Only a qualified electrician may install a socket or replace the connecting cable, taking the appropriate regulations into account.
The appliance must only be connected with the power cable provided. Connect the power cable to the back of the appliance.
Connecting cables with various plug types are available from after-sales service.
No multi-plugs, multiple connectors or extension leads must be used. Overloading causes a risk of fire.
If the plug can no longer be reached after the installation, a partition must be provided in the phases in the permanent electrical installation in accordance with the installation regulations.

Tools

You require the following tools for the installation.

Measuring tape
Calliper
Pencil
Angle bracket
Torx 20 screwdriver
Large flat-tipped screwdriver
Medium-sized flat-tipped screwdriver
Combination pliers
Cordless combination drill
Drill, 4/5/6.5/10 diameter
Countersink

Preparing the appliance

A pump that contains oil is installed in the appliance. If the incline is too great, this oil may flow out of the pump. Do not tip the appliance or upend it.
ATTENTION!
The oil from the vacuum pump may leak out when it is tipped or tilted, and may damage the appliance.

Do not move the appliance if the transport locks for the pump are not installed.
When uninstalling the appliance, secure the transport locks again before moving the appliance.

Requirement: Use a suitable tool to remove the transport locks and install the oil filter.

Carefully lift the appliance out of the packaging.
Remove the transport lock for the pump from the top of the appliance.
Secure the transport lock to the rear of the appliance for further use.
Install the oil filter.
Place the lid into the opening and move it to the left.
WARNING ‒ Risk of tipping!
After removing the transportation lock, the drawer may open and the appliance may tip over.
▶ Keep the drawer closed.
▶ Weigh down the appliance with a weight.
▶ Only open the drawer if the tilt protection is installed.
Remove the transport lock screws.
Insert the power cord at the rear of the appliance.

Preparing the units

Install the tilt protection. Ensure that the screws are mounted in the upper part of the elongated holes.
Use the installation aid to secure the mounting bracket to the unit.

Installing the appliance

WARNING ‒ Risk of electric shock!
If the insulation of the power cord is damaged, this is dangerous.

Never let the power cord come into contact with hot appliance parts or heat sources.
Never let the power cord come into contact with sharp points or edges.
Never kink, crush or modify the power cord.

WARNING ‒ Risk of injury!
After removing the transport lock, the drawer may open suddenly during transport.
▶ Transport the appliance in such a way that the drawer does not accidentally open.

Insert the power cord into a protective contact socket.
WARNING ‒ Risk of injury!
The high weight of the appliance may result in injury when lifted.
▶ Do not lift the appliance on your own.
Slide the appliance into the unit.
If the appliance cannot slide in, adjust the height of the tilt protection brackets. To do this, undo the screws and push the tilt protection brackets upwards.
Centre the appliance.
To check the tilt protection, open the drawer carefully.
Select appropriate decorative panels.
To secure the appliance, screw the decorative panels onto the mounting brackets.
The groove on the decorative panel should face outwards in each case.

Preparing the furniture panel

Requirements

The thickness of the furniture panel is at least.
19 mm.
The width of the furniture panel is 596–590 mm.
The recommended height of the furniture panel is 142–156 mm.
The furniture panel is made of wood or wood-like material.
The furniture panel has a handle or a recessed grip.
Mark the centre of the top edge of the furniture panel.

Installing the furniture panel

Requirement: Wear gloves.

Measure the width of the fitted unit and mark the centre of the intermediate floor.
Use the combination pliers to bend the hooks on the front panel upwards by 90°.
Mount the front panel on the appliance and push it downwards as far as it will go.
Check whether the front panel is mounted straight.
Stick the double-sided adhesive tape to the front panel as an installation aid.
Align the furniture panel and push the front panel on.
The furniture panel sticks to the front panel.
Carefully open the drawer.
Mark the top edge of the front panel on the furniture panel.
Detach the front panel with the furniture panel.
Check the position of the front panel on the furniture panel.
Mark the elongated holes.
Loosen the front panel from the furniture panel and remove the double-sided adhesive tape.
Drill the holes in the middle of elongated holes.
Countersink the holes.
Screw in the threaded sleeves until they are flush with the surface of the furniture panel.
Install the handle on the furniture panel because the screws for the handle are no longer accessible following installation of the front panel. The screws for the handle must be countersunk.
Place the front panel on the furniture panel and align it.
Screw the front panel in loosely using the concave washers and the screws. Do not tighten the screws to ensure that the panel can still move.
Realign the front panel with the furniture panel.
Screw in the side screws and tighten them.
Mount the furniture panel with the front panel on the appliance.