GAGGENAU AC230101 Ceiling-Mounted Ventilation System User Manual
- June 9, 2024
- Gaggenau
Table of Contents
- Safety
- Preventing material damage
- Environmental protection and saving energy
- Operating modes
- Familiarising yourself with your appliance
- Before using for the first time
- Basic operation
- Home Connect
- Hob-based hood control
- Cleaning and servicing
- Troubleshooting
- Customer Service
- Accessories
- Disposal
- Declaration of Conformity
- Installation instructions
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
User manual and installation instructions
AC230101
Ceiling-mounted ventilation system
User Manual
Safety
Observe the following safety instructions.
1.1 General information
- Read this instruction manual carefully.
- Keep the instruction manual and the product information safe for future reference or for the next owner.
- Do not connect the appliance if it has been damaged in transit.
1.2 Intended use
This appliance is designed only to be built into kitchen units. Read the
special installation instructions.
The appliance can only be used safely if it is correctly installed according
to the safety instructions. The installer is responsible for ensuring that the
appliance works perfectly at its installation location.
Only use this appliance:
- For extracting cooking vapour.
- In private households and in enclosed spaces in a domestic environment.
- Up to an altitude of max. 2000 m above sea level.
Do not use the appliance:
- With an external timer.
1.3 Restriction on user group
This appliance may be used by children aged
8 or over and by people who have reduced physical, sensory or mental abilities
or inadequate experience and/or knowledge, provided that they are supervised
or have been instructed on how to use the appliance safely and have understood
the resulting dangers.
Do not let children play with the appliance.
Children must not perform cleaning or user maintenance unless they are at
least 15 years old and are being supervised.
Keep children under the age of 8 years away from the appliance and power
cable.
1.4 Safe use
WARNING ‒ Risk of suffocation!
Children may put packaging material over their heads or wrap themselves up in
it and suffocate.
- Keep packaging material away from children.
- Do not let children play with packaging material. Children may breathe in or swallow small parts, causing them to suffocate.
- Keep small parts away from children.
- Do not let children play with small parts.
WARNING ‒ Risk of fire!
Fatty deposits in the grease filters may catch fire.
-
Never operate the appliance without a grease filter.
-
Clean the grease filters regularly.
-
Never work with naked flames close to the appliance (e.g. flambéing).
-
Do not install the appliance near a solid fuel heating appliance (e.g. wood- or coalburning) unless the heating appliance has a sealed, non-removable cover. There must be no flying sparks.
Hot oil or grease ignites very quickly. -
Always supervise hot oil and fat.
-
Never extinguish burning oil or fat with water. Switch off the cooking zone.
Extinguish flames carefully using a lid, fire blanket or something similar.
When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become
damaged or catch fire. -
Only operate the gas burners with cookware on them.
Operating multiple gas hobs at the same time generates a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. -
Only operate the gas hobs with cookware on them.
-
Select the highest fan setting.
-
Never operate two gas hobs simultaneously on the highest flame for longer than 15 minutes. Two gas hobs correspond to one large burner.
-
Never operate large burners of more than 5 kW with the highest flame for longer than 15 minutes, e.g. a wok.
-
The appliance must only be combined with gas hobs with a total output of up to 18 kW.
WARNING ‒ Risk of burns!
The accessible parts of the appliance become hot during operation.
-
Never touch these hot parts.
-
Keep children at a safe distance.
The appliance becomes hot during operation. -
Allow the appliance to cool down before cleaning.
WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.
-
Carefully clean the appliance interior.
Items placed on the appliance may fall off. -
Do not place any objects on the appliance.
Changes to the electrical or mechanical assembly are dangerous and may lead to malfunctions. -
Do not make any changes to the electrical or mechanical assembly.
The filter cover may swing out. -
Open the filter cover slowly.
-
Take hold of the filter cover after opening until it no longer swings out.
-
Close the filter cover slowly.
Risk of injury when opening and closing the hinges. -
Keep your hands away from the hinges.
Children may swallow batteries. -
Keep batteries out of the reach of children.
-
Keep an eye on any children when you are replacing batteries.
Batteries may explode. -
Do not charge the batteries.
-
Do not short-circuit the batteries.
-
Do not throw batteries into a fire.
Risk of falling when working on the appliance -
Use a stable stepladder.
-
Do not lean over the hob.
-
Do not step on the hob or the work surface.
If the appliance is operated by another person via the
Home Connect app during cleaning, this increases the risk of injury. -
Before cleaning, disconnect the appliance from the Home Connect app.
WARNING ‒ Risk of electric shock!
If the appliance or the power cord is damaged, this is dangerous.
-
Never operate a damaged appliance.
-
Never pull on the power cord to unplug the appliance. Always unplug the appliance at the mains.
-
If the appliance or the power cord is damaged, immediately unplug the power cord or switch off the fuse in the fuse box.
-
Call customer services. → Page 33 Incorrect repairs are dangerous.
-
Repairs to the appliance should only be carried out by trained specialist staff.
-
Only use genuine spare parts when repairing the appliance.
-
If the power cord of this appliance is damaged, it must be replaced by trained specialist staff.
An ingress of moisture can cause an electric shock. -
Before cleaning, pull out the mains plug or switch off the fuse in the fuse box.
-
Do not use steam- or high-pressure cleaners to clean the appliance.
WARNING ‒ Risk of explosion!
Highly caustic alkaline or highly acidic cleaning agents in conjunction with
aluminium parts in the interior of the appliance may cause explosions.
-
Never use highly caustic alkaline or highly acidic cleaning agents. In particular, do not use commercial or industrial cleaning agents in conjunction with aluminium parts,
e.g. grease filter on extractor hoods.
WARNING ‒ Risk of fire!
Fatty deposits in the grease filters may catch fire. -
Clean the grease filters regularly.
WARNING ‒ Risk of injury!
Improper repairs are dangerous. -
Repairs to the appliance should only be carried out by trained specialist staff.
-
If the appliance is defective, call Customer Service.
WARNING ‒ Risk of electric shock!
Penetrating moisture may cause an electric shock. -
Do not use wet sponge cloths.
Preventing material damage
2.1 Avoiding material damage
ATTENTION!
Condensate may cause corrosion damage.
-
To prevent condensation from building up, switch on the appliance during cooking.
If moisture gets into the controls, this may result in damage. -
Never clean controls with a wet cloth.
Incorrect cleaning damages the surfaces. -
Follow the cleaning instructions.
-
Do not use harsh or abrasive detergents.
-
Clean stainless steel surfaces in the direction of the finish only.
-
Never clean controls with stainless steel cleaners.
Condensation that flows back in may damage the appliance. -
The air extraction duct must be installed with a gradient of at least 1° from the appliance.
If you put incorrect stress on the design elements, they may break off. -
Do not pull design elements.
-
Do not place objects on the design elements or hang objects from them.
Leaking batteries may damage the remote control. -
Remove the batteries if you are not using the remote control.
-
Safely dispose of empty or defective batteries in an environmentally friendly manner.
There is a risk of surface damage if you do not peel off the protective film. -
Remove the protective film from all parts of the appliance before using for the first time.
Painted surfaces are easily damaged. -
Follow the cleaning instructions.
→ “Cleaning the appliance”, Page 29 -
Ensure that the painted surfaces are not scratched.
Environmental protection and saving energy
3.1 Disposing of packaging
The packaging materials are environmentally compatible and can be recycled.
- Sort the individual components by type and dispose of them separately.
3.2 Saving energy
If you follow these instructions, your appliance will use less power.
Adjust the fan speed to the amount of steam produced during cooking.
-
The lower the fan speed, the less energy is consumed. Only use the intensive mode as required.
If cooking produces large amounts of steam, select a higher fan speed in good time. -
The odours are distributed around the room less.
Switch off the lighting if it is no longer required. -
When the lighting is switched off, it does not consume any energy.
Clean or replace the filters at regular intervals. -
The effectiveness of the filter is retained.
Put the cooking lid on. -
The cooking vapours and condensation are reduced.
Only use the additional functions if required. -
Switching off additional functions reduces power consumption.
Operating modes
4.1 Air recirculation mode
The air which is drawn in is cleaned by the grease filters and an odour
filter, and conveyed back into the
room.
To bind odours in circulating-air mode, you must install an odour filter. The
different options for operating the appliance in circulating-air mode can be
found in our catalogue.
Alternatively, ask your dealer. The required accessories are available from
specialist retailers, from customer service or from the Online Shop.
Familiarising yourself with your appliance
5.1 Controls
You can use the control panel to configure all functions of your appliance and
to obtain information about the operating status.
Tip: Align the remote control as precisely as possible to the infrared
receiver for the LED display.
| Switch the appliance on or off
---|---
A
| Switching automatic mode 1 on or off
+
| Increase the fan setting
-
| Decrease the fan setting
| Switch the intermittent ventilation on or off.
1
| Depending on the appliance specifications
| Home Connect
| Reset the filter saturation indicator
1
| Depending on the appliance specifications
5.2 LED display
Die LED-Anzeige zeigt eingestellte Werte und Funktionen.
1 | Fan setting 1/grease filter saturation display |
---|---|
2 | Fan setting 2/odour filter saturation indicator |
3 | Fan setting 3 |
4 | Intensive mode 1 |
5 | Intensive mode 2 |
6 | Automatic mode 1 /fan run-on time/interval ventilation |
7 | Home Connect |
8 | Infrared receiver |
1 | Depending on the appliance specifications |
Before using for the first time
Configure the settings for initial start-up. Clean the appliance and accessories.
Basic operation
7.1 Switching on the appliance
Requirement: Align the remote control as precisely as possible to the infrared
receiver for the LED display.
- Press to switch on the appliance.
√ The appliance starts at fan setting 2.
√ The LED for the set fan setting lights up in the LED display.
7.2 Switching off the appliance
Switch the appliance off when you are not using it.
- Press .
√ The fan run-on is switched on, LED 6 flashes in the LED display for the fan run-on.
√ The fan automatically switches off after approx. 10 minutes.
7.3 Selecting a fan setting
- Press + or -.
√ The LED for the set fan setting lights up in the LED display.
7.4 Switching on intensive mode
If particularly strong odours or vapours develop, you can use intensive mode.
√ After approx. 6 minutes, the appliance automatically switches to fan setting
3.
7.5 Switching off intensive mode¹
- To select a fan setting of your choice, press .
7.6 Switching on automatic mode¹
The optimum fan setting is set automatically using a sensor.
- Press
A
.
√ In the LED display, LED 6 lights up for automatic mode.
7.7 Switch off automatic mode 1
- Press
A
.
√ The appliance switches to the fan setting that was previously set.
√ The ventilation is automatically ended when the sensor detects no further change in the room air quality.
√ Automatic mode runs for a maximum of four hours.
7.8 Switching on intermittent ventilation
With interval ventilation, the ventilation switches on for approx. 6 minutes
every hour.
Note: In the Home Connect app, you can set the time and fan setting
individually.
- Press .
√ In the LED display, LED 6 flashes continuously, the LED for the selected fan setting lights up on the appliance.
√As soon as the ventilation time ends, the LED for the fan setting you have selected goes out. LED 6 continues to flash.
7.9 Switching off interval ventilation
- Press .
7.10 Sensor control¹
In automatic mode, a sensor in the appliance detects the intensity of the
cooking and roasting fumes. Depending on the setting of the sensor
sensitivity, the optimum fan setting is automatically switched on.
If the sensor control system reacts too weakly or too strongly, the setting
for the sensor sensitivity may change.
- Default setting: Fan setting 3
- Lowest setting: Fan setting 1
- Highest setting: Fan setting 5
7.11 Setting the sensor control¹
Requirement: The appliance is switched off.
-
Press and hold and for approx. 3 seconds.
-
Press or to change the setting.
To cancel the setting, press . -
To save the setting, press and hold and for approx. 3 seconds.
Or wait approx. 10 seconds until the setting is saved automatically.
√ A signal tone sounds as soon as the selected setting is saved.
1 Depending on the appliance specifications
7.12 Resetting the saturation indicator
After cleaning the grease filter or after changing the odour filter, the
saturation indicator can be reset.
Requirements
- After the appliance has been switched off, LED 1 flashes in the LED display for the grease filter saturation display and/or LED 2 flashes for the saturation indicator for the odour filter.
- A signal sounds repeatedly.
▶ Press .
√ The saturation indicator is reset.
7.13 Setting the saturation indicator
The saturation indicator must be adjusted depending on the filter used.
Requirement: The appliance is switched off.
-
Press and hold and for approx. three seconds.
‒ To set circulating-air mode (non-regenerable filter), press +/- until LED 2 lights up in the LED display.
‒ To set circulating-air mode (non-regenerable filter), press +/- until LED 3 lights up in the LED display.
‒ To convert the electronic control back to operation without the air recirculation filter, press +/- until LED 1 lights up on the LED display. -
To save the setting, press and hold and for approx. three seconds.
Or wait approx. 10 seconds until the setting is saved automatically.
To cancel the setting, press .
√ A signal tone sounds as soon as the selected setting is saved.
7.14 Switching on the button tone
The button tones can be switched on.
Requirement: The appliance is switched off.
-
Press and hold and – for approx. three seconds.
√ In the LED display, the LED for the setting that is currently selected lights up. -
Press + or – until LED 1 lights up in the LED display.
To cancel the setting, press . -
To save the setting, press and hold and – for approx. three seconds.
Or wait approx. 10 seconds until the setting is saved automatically.
√ A signal tone sounds as soon as the selected setting is saved.
7.15 Switching the button tone off
The button tones can be switched off.
Note: Signal tones for the appliance are always switched on and cannot be
switched off.
Requirement: The appliance is switched off.
-
Press and hold and for approx. three seconds.
√ In the LED display, the LED for the setting that is currently selected lights up. -
Press + or – until LED 2 lights up in the LED display.
To cancel the setting, press . -
To save the setting, press and hold and – for approx. three seconds.
Or wait approx. 10 seconds until the setting is saved automatically.
√ A signal tone sounds as soon as the selected setting is saved.
Home Connect
This appliance is network-capable. Connecting your appliance to a mobile
device lets you control its functions via the
Home Connect app, adjust its basic settings and monitor its operating status.
The Home Connect services are not available in every country. The availability
of the Home Connect function depends on the availability of Home Connect
services in your country. You can find information about this at: www.home-
connect.com.
The Home Connect app guides you through the entire login process. Follow the
instructions in the Home Connect app to configure the settings.
If the appliance is not connected to your home network, it functions as an
appliance with no network connection and can still be operated via the
display.
Tips
- Please consult the documents supplied by Home Connect.
- Please also follow the instructions in the Home Connect app.
Notes
-
Please note the safety precautions in this instruction manual and make sure that they are also observed when operating the appliance via the Home Connect app.
→ “Safety”, Page 22 -
Operating the appliance on the appliance itself always takes priority. During this time it is not possible to operate the appliance using the Home Connect app.
-
In networked standby mode, the appliance requires a maximum of 2 W.
-
If you need your device’s MAC address to connect to your home network, you can find this next to the rating plate. → Page 33
8.1 Setting up Home Connect
Requirements
- The appliance is connected to the power supply and is switched on.
- You have a mobile device with a current version of the iOS or Android operating system, e.g. a smartphone.
- The mobile device and the appliance are within range of your home network’s Wi-Fi signal.
- Download the Home Connect app.
- Open the Home Connect app and scan the following QR code.https://qr.home-connect.com/?aG9tZWNvbm5lY3Q6Ly9vcGVuUGFpcmluZz9wc2V1ZG9WaWI9Q0dWX1YzMl9HRyZjaWQ9cGFpcmluZ19nZ19yZXVfbWRhflYzMl9HR351c2VybWFudWFsfmhvb2R+cXJjb2RlfmNvbW0=
- Follow the instructions in the Home Connect app.
8.2 Resetting the connection
Saved connections to the home network and to Home Connect can be reset.
- Press and hold and until LED 7 goes out in the LED display.
√ An audible signal sounds.
8.3 Software update
Your appliance’s software can be updated using the software update function,
e.g. for the purposes of optimisation, troubleshooting or security updates.
To do this, you must be a registered Home Connect user, have installed the app
on your mobile device and be connected to the Home Connect server.
As soon as a software update is available, you will be informed via the Home
Connect app and will be able to start the software update via the app. Once
the update has been successfully downloaded, you can start installing it via
the Home Connect app if you are in your home network (Wi-Fi). The Home Connect
app informs you once installation is successful.
Notes
-
The software update consists of two steps.
– The first step is the download.
– The second step is the installation on your appliance. -
You can continue to use your appliance as normal while updates are downloading. Depending on your personal settings in the app, software updates can also be set to download automatically.
-
Installation takes a few minutes. You cannot use your appliance during installation.
-
We recommend that you install security updates as soon as possible.
8.4 Remote diagnostics
Customer Service can use Remote Diagnostics to access your appliance if you
contact them, have your appliance connected to the Home Connect server and if
Remote Diagnostics is available in the country in which you are using the
appliance.
Tip: For further information and details about the availability of Remote
Diagnostics in your country, please visit the service/support section of your
local website: www.home-connect.com
8.5 Data protection
Please see the information on data protection.
The first time your appliance is registered on a home network connected to the
Internet, your appliance will transmit the following types of data to the Home
Connect server (initial registration):
- Unique appliance identification (consisting of appliance codes as well as the MAC address of the Wi-Fi communication module installed).
- Security certificate of the Wi-Fi communication module (to ensure a secure data connection).
- The current software and hardware version of your appliance.
- Status of any previous reset to factory settings.
This initial registration prepares the Home Connect functions for use and is
only required when you want to use the Home Connect functions for the first
time.
Note: Please note that the Home Connect functions can only be utilised
with the Home Connect app. Information on data protection can be retrieved in
the Home Connect app.
Hob-based hood control
You can connect your appliance to a suitable hob and, in this way, control the
functions of your appliance via the hob.
If the hob and the extractor hood are Home Connectcompatible, connect the
appliances in the Home Connect app. To do this, connect the two appliances to
Home Connect and follow the instructions in the app.
Notes
- Please note the safety precautions in the instruction manual for your appliance and ensure that they are also observed when operating the appliance via the hob-based hood control.
- Operating your appliance always takes priority. It is not possible to use the hob-based hood control during this time.
- You can only connect to the extractor hood via the Home Connect app. Other connection routes are no longer supported.
Cleaning and servicing
To keep your appliance working efficiently for a long time, it is important to
clean and maintain it carefully.
10.1 Cleaning products
You can obtain suitable cleaning products from aftersales service or the
online shop.
WARNING ‒ Risk of electric shock!
An ingress of moisture can cause an electric shock.
- Before cleaning, pull out the mains plug or switch off the fuse in the fuse box.
- Do not use steam- or high-pressure cleaners to clean the appliance.
WARNING ‒ Risk of burns!
The appliance becomes hot during operation.
- Allow the appliance to cool down before cleaning.
ATTENTION!
Unsuitable cleaning products may damage the surfaces of the appliance.
- Do not use harsh or abrasive detergents.
- Do not use cleaning products with a high alcohol content.
- Do not use hard scouring pads or cleaning sponges.
- Only use glass cleaners, glass scrapers or stainless steel care products if recommended in the cleaning instructions for the relevant part.
- Wash sponge cloths thoroughly before use.
10.2 Cleaning the appliance
Clean the appliance as specified. This will ensure that the different parts
and surfaces of the appliance are not damaged by incorrect cleaning or
unsuitable cleaning
products.
WARNING ‒ Risk of explosion!
Highly caustic alkaline or highly acidic cleaning agents in conjunction with
aluminium parts in the interior of the appliance may cause explosions.
- Never use highly caustic alkaline or highly acidic cleaning agents. In particular, do not use commercial or industrial cleaning agents in conjunction with aluminium parts, e.g. grease filter on extractor hoods.
WARNING ‒ Risk of electric shock!
An ingress of moisture can cause an electric shock.
- Before cleaning, pull out the mains plug or switch off the fuse in the fuse box.
- Do not use steam- or high-pressure cleaners to clean the appliance.
WARNING ‒ Risk of burns!
The appliance becomes hot during operation.
- Allow the appliance to cool down before cleaning.
WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.
- Carefully clean the appliance interior.
-
Observe the information regarding the cleaning agents.
→ “Cleaning products”, Page 29 -
Clean as follows, depending on the surface:
‒ Clean stainless steel surfaces in the direction of the finish using a sponge cloth and hot soapy water.
‒ Clean painted surfaces using a damp sponge cloth and hot soapy water.
‒ Clean aluminium using a soft cloth and glass cleaner.
‒ Clean plastic using a soft cloth and glass cleaner.
‒ Clean glass using a soft cloth and glass cleaner. -
Dry with a soft cloth.
-
Apply a thin layer of the stainless steel cleaning product to stainless steel surfaces using a soft cloth.
You can obtain stainless steel cleaning products from the after-sales service or the online shop.
10.3 Cleaning controls
WARNING ‒ Risk of electric shock!
Penetrating moisture may cause an electric shock.
- Do not use wet sponge cloths.
-
Observe the information regarding the cleaning agents.
→ “Cleaning products”, Page 29 -
Clean using a damp sponge cloth and hot soapy water.
-
Dry with a soft cloth.
10.4 Removing the grease filter
WARNING ‒ Risk of injury!
The filter cover may swing out.
- Open the filter cover slowly.
- Take hold of the filter cover after opening until it no longer swings out.
- Close the filter cover slowly.
Risk of falling when working on the appliance
- Use a stable stepladder.
- Do not lean over the hob.
- Do not step on the hob or the work surface.
-
Press the lock on the filter cover. To prevent the filter cover from swinging down suddenly, hold onto the filter cover firmly with two hands.
-
Open the filter cover by pulling it downwards.
-
ATTENTION!
Falling grease filters may damage the hob below.
▶ Grip below the grease filter with one hand.
Open the locks on the grease filters. -
Remove the grease filters from the holders.
To prevent grease from dripping, hold the grease filter horizontally.
10.5 Cleaning grease filters in the dishwasher
The grease filters filter the grease from the cooking vapour. Regularly
cleaned grease filters guarantee a high level of grease removal. We recommend
cleaning the grease filters every two months.
WARNING ‒ Risk of fire!
Fatty deposits in the grease filters may catch fire.
- Clean the grease filters regularly.
ATTENTION!
The grease filters may become damaged if they are squeezed.
- Do not squeeze the grease filters.
Note: When cleaning the grease filter in the dishwasher, light
discolouration may occur. This discolouration has no effect on the performance
of the metal grease filters.
Requirement: The grease filters have been removed.
→ “Removing the grease filter”, Page 30
-
Observe the information regarding the cleaning agents.
→ “Cleaning products”, Page 29 -
Place the grease filters loosely into the dishwasher.
Do not clean heavily soiled grease filters with utensils.
Use special grease solvent for stubborn dirt. You can obtain grease solvents from customer service or the online shop. -
Start the dishwasher.
Select a temperature of no more than 70 °C. -
Allow the grease filters to drain.
10.6 Cleaning grease filters manually
The grease filters filter the grease from the cooking vapour. Regularly
cleaned grease filters guarantee a high level of grease removal. We recommend
cleaning the grease filters every two months.
WARNING ‒ Risk of fire!
Fatty deposits in the grease filters may catch fire.
- Clean the grease filters regularly.
Requirement: The grease filters have been removed.
→ “Removing the grease filter”, Page 30
-
Observe the information regarding the cleaning agents.
→ “Cleaning products”, Page 29 -
Soak the grease filter in hot soapy water.
Use special grease solvent for stubborn dirt. You can obtain grease solvents from customer service or the online shop. -
Use a brush to clean the grease filters.
-
Rinse the grease filters thoroughly.
-
Allow the grease filters to drain.
10.7 Fitting grease filters
ATTENTION!
Falling grease filters may damage the hob below.
- Grip below the grease filter with one hand.
- Fit the grease filters.
- Fold the grease filters upwards and engage the locks.
- Make sure that the locks engage.
- Close the filter cover.
- Make sure that the filter cover locks engage correctly.
10.8 Odour filter for recirculating air mode
You can obtain odour filters from the after-sales service or the online shop.
Only use original odour filters.
→ “Accessories”, Page 33
Replacing the odour filter
Requirement: The grease filters have been removed.
- Open the odour filter cartridge.
- Remove the odour filter.
- Remove the new odour filter from the packaging.
- Insert the odour filter. Insert the odour filter in the correct direction.
- Close the odour filter cartridge.
- → “Fitting grease filters”, Page 31.
10.9 Replacing the batteries in the remote control
WARNING ‒ Risk of injury!
Children may swallow batteries.
-
Keep batteries out of the reach of children.
-
Keep an eye on any children when you are replacing batteries.
Batteries may explode. -
Do not charge the batteries.
-
Do not short-circuit the batteries.
-
Do not throw batteries into a fire.
ATTENTION!
Improper handling of batteries.
-
Do not short-circuit the terminals.
-
Only use the specified type of batteries.
-
Do not use different battery types together.
-
Do not use new and used batteries together.
-
Do not use rechargeable batteries.
Leaking batteries may damage the remote control. -
Remove the batteries if you are not using the remote control.
-
Safely dispose of empty or defective batteries in an environmentally friendly manner.
- Remove the cover. 1 2
- Remove the empty batteries. 3
- Insert the new batteries (3 V CR 2032). 1
- Close the cover. 2 3
- Dispose of the empty batteries in an environmentally friendly manner.
Troubleshooting
You can rectify minor faults on your appliance yourself.
Read the troubleshooting information before contacting after-sales service.
This will avoid unnecessary costs.
WARNING ‒ Risk of injury!
Improper repairs are dangerous.
- Repairs to the appliance should only be carried out by trained specialist staff.
- If the appliance is defective, call Customer Service.
WARNING ‒ Risk of electric shock!
Incorrect repairs are dangerous.
- Repairs to the appliance should only be carried out by trained specialist staff.
- Only use genuine spare parts when repairing the appliance.
- If the power cord of this appliance is damaged, it must be replaced by trained specialist staff.
11.1 Malfunctions
Fault | Cause and troubleshooting |
---|---|
The appliance is not working. | The mains plug of the power cord is not plugged |
in.
▶ Connect the appliance to the power supply.
The circuit breaker in the fuse box has tripped.
▶ Check the circuit breaker in the fuse box.
There has been a power cut.
▶ Check whether the lighting in your kitchen or other appliances are working.
Remote control not working.| The batteries are flat.
▶ → “Replacing the batteries in the remote control”, Page 31
In the LED display, the LEDs flash one to
five times after the appliance is switched off.| The batteries are almost
empty.
▶ → “Replacing the batteries in the remote control”, Page 31
LED 1 flashes in the LED display.| The grease filters are saturated.
▶ → “Cleaning grease filters in the dishwasher”, Page 31
▶ → “Cleaning grease filters manually”, Page 31
LED 2 flashes in the LED display.| The odour filters are saturated.
▶ Change the odour filter. → Page 31
Customer Service
Function-relevant genuine spare parts according to the corresponding Ecodesign
Order can be obtained from Customer Service for a period of at least 10 years
from the date on which your appliance was placed on the market within the
European Economic Area.
Note: Under the terms of the manufacturer’s warranty the use of Customer
Service is free of charge.
Detailed information on the warranty period and terms of warranty in your
country is available from our aftersales service, your retailer or on our
website.
If you contact Customer Service, you will require the product number (E-Nr.)
and the production number (FD) of your appliance.
The contact details for Customer Service can be found in the enclosed Customer
Service directory or on our website.
12.1 Product number (E-Nr.) and production number (FD)
You can find the product number (E-Nr.) and the production number (FD) on the
appliance’s rating plate.
Depending on the model, the rating plate can be found:
- Inside the appliance (remove grease filters for access).
- On top of the appliance.
M ake a note of your appliance’s details and the Customer Service telephone number to find themagain quickly.
Accessories
You can buy accessories from the after-sales service, from specialist
retailers or online. Only use original accessories, as these have been
specifically designed for your appliance.
Accessories vary from one appliance to another.
When purchasing accessories, always quote the exact product number (E no.) of
your appliance. → Page 33
You can find out which accessories are available for your appliance in our
catalogue, in the online shop or from our after-sales service.
www.gaggenau.com
Accessories | Order number |
---|---|
Regenerable odour filter | AA200122 |
Non-regenerable odour filter | AA200121 |
Disposal
14.1 Disposing of old appliance
Valuable raw materials can be reused by recycling.
- Unplug the appliance from the mains.
- Cut through the power cord.
- Dispose of the appliance in an environmentally friendly manner.
Information about current disposal methods are available from your specialist dealer or local authority.
**** This appliance is labelled in accordance with European Directive
2012/19/EU concerning used electrical and electronic appliances (waste
electrical and electronic equipment – WEEE).
The guideline determines the framework for the return and recycling of used
appliances as applicable throughout the EU.
14.2 Disposing of batteries
Batteries should be recycled in an environmentally friendly manner. Do not
dispose of the batteries in the household rubbish.
- Dispose of batteries in an environmentally friendly manner.
According to the European Guideline 2006/66/EC, defective or used battery packs/batteries, must be collected separately and disposed of in an environmentally correct manner.
Declaration of Conformity
BSH Hausgeräte GmbH hereby declares that the appliance with Home Connect
functionality conforms to the basic requirements and other relevant provisions
of Directive
2014/53/EU.
A detailed RED Declaration of Conformity can be found online at
www.gaggenau.com among the additional documents on
the product page for your appliance.
**** Hereby, BSH Hausgeräte GmbH declares that the appliance with Home
Connect functionality is in compliance with relevant statutory requirements.¹
A detailed Declaration of Conformity can be found online at
www.gaggenau.com/gb among the additional
documents on the product page for your appliance.1
Only applies to Great Britain
2.4 GHz band (2400–2483.5 MHz): Max. 100 mW
5 GHz band (5150–5350 MHz + 5470–5725 MHz): Max. 100 mW
| BE| BG| CZ| DK| DE| EE| IE| EL| ES
---|---|---|---|---|---|---|---|---|---
FR| HR| IT| CY| LI| LV| LT| LU| HU
MT| NL| AT| PL| PT| RO| SI| SK| FI
SE| NO| CH| TR| IS| UK (NI)| | |
5 GHz WLAN (Wi-Fi): For indoor use only.
AL| BA| MD| ME| MK| RS| UK| UA| |
5 GHz WLAN (Wi-Fi): For indoor use only.
Installation instructions
Observe this information when installing the appliance.
16.1 Included with the appliance
After unpacking all parts, check for any damage in transit and completeness of
the delivery.
16.2 Safety clearances
Comply with the safety clearances for the appliance.
16.3 Dimensions
You will find the dimensions of the appliance here
16.4 Secure installation
Follow these safety instructions when installing the appliance.
WARNING ‒ Risk of suffocation!
Children may put packaging material over their heads or wrap themselves up in
it and suffocate.
- Keep packaging material away from children.
- Do not let children play with packaging material.
WARNING ‒ Risk of fire!
Grease deposits in the grease filter may catch fire.
-
The specified safety clearances must be complied with in order to prevent a build-up of heat.
-
Observe the specifications for your cooking appliances. If the installation instructions for the cooking appliances specify a different clearance, the larger of the two must always be provided for. If gas hobs and electric hobs are operated together, the largest specified clearance applies.
The grease deposits in the grease filter may catch fire. -
Never work with naked flames close to the appliance (e.g. flambéing).
-
Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, non-removable cover is present. There must be no flying sparks.
WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.
-
Wear protective gloves.
The appliance may fall down if it has not been properly fastened in place. -
All fastening components must be fixed firmly and securely in place.
The appliance is heavy. -
To move the appliance, two people are required.
-
Use only suitable tools and equipment.
The appliance is heavy. -
The appliance must not be fitted directly onto plasterboard or similar lightweight materials.
-
To ensure correct installation, you must use a material which is sufficiently stable and suitable for both the structural conditions and the weight of the appliance.
Changes to the electrical or mechanical assembly are dangerous and may lead to malfunctions. -
Do not make any changes to the electrical or mechanical assembly.
Risk of falling when working on the appliance -
Use a stable stepladder.
-
Do not lean over the hob.
-
Do not step on the hob or the work surface.
The filter cover may swing out. -
Open the filter cover slowly.
-
Take hold of the filter cover after opening until it no longer swings out.
-
Close the filter cover slowly.
Risk of injury when opening and closing the hinges. -
Keep your hands away from the hinges.
WARNING ‒ Risk of electric shock!
Sharp-edged components inside the appliance may damage the connecting cable.
-
Do not kink or trap the connecting cable.
If the appliance or the power cord is damaged, this is dangerous. -
Never operate a damaged appliance.
-
Never pull on the power cord to unplug the appliance. Always unplug the appliance at the mains.
-
If the appliance or the power cord is damaged, immediately unplug the power cord or switch off the fuse in the fuse box.
-
Call customer services. → Page 33 Incorrect repairs are dangerous.
-
Repairs to the appliance should only be carried out by trained specialist staff.
-
Only use genuine spare parts when repairing the appliance.
-
If the power cord of this appliance is damaged, it must be replaced by trained specialist staff.
Incorrect installation is dangerous. -
Connect and operate the appliance only in accordance with the specifications on the rating plate.
-
Connect the appliance to a power supply with alternating current only via a properly installed socket with earthing.
-
The protective conductor system of the domestic electrical installation must be properly installed.
-
Never equip the appliance with an external switching device, e.g. a timer or remote control.
-
When the appliance is installed, the mains plug of the power cord must be freely accessible. If free access is not possible, an all-pole isolating switch must be installed in the permanent electrical installation according to the conditions of Overvoltage Category III and according to the installation regulations.
-
When installing the appliance, check that the power cable is not trapped or damaged.
16.5 Information on the installation situation
- Install this appliance on the kitchen ceiling or a stable suspended ceiling.
- To install additional special accessory parts, observe the enclosed installation instructions.
- The appliance finds it more difficult to draw in the cooking vapours the further away they are from the hotplate. For optimum performance, a maximum distance of 1500 mm is recommended.
- The width of the extractor hood must correspond at least with the width of the hob.
- To optimally detect the cooking vapours, install the appliance in the middle of the hob.
16.6 Instructions for the electrical connection
In order to safely connect the appliance to the electrical system, follow
these instructions.
WARNING ‒ Risk of electric shock!
It must always be possible to disconnect the appliance from the electricity
supply. The appliance must only be connected to a protective contact socket
that has been correctly installed.
-
The mains plug for the mains power cable must be easily accessible after the appliance is installed.
-
If this is not possible, an all-pole isolating switch must be integrated into the permanent electrical installation according to the conditions of overvoltage category III and according to the installation regulations.
-
The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual-current circuit breaker (RCCB) in the appliance’s power supply circuit. Sharp-edged components inside the appliance may damage the connecting cable.
-
Do not kink or trap the connecting cable.
-
The connection data can be found on the rating plate. → Seite 33
-
The connecting cable is approx. 1.30 m long.
-
This appliance complies with the EC interference suppression regulations.
-
The appliance corresponds to protection class 1.
You should therefore only use the appliance with a protective earth connection. -
Do not connect the appliance to the power supply during installation.
-
Ensure that the protection against contact is guaranteed during installation.
-
Only a licensed professional may connect appliances without plugs. They are subject to the requirements of the local electricity provider.
16.7 General information
Follow these general instructions during the installation.
- For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.
- When discharging the exhaust air, the official and legal regulations, such as the regional building code., must be observed.
- In order to freely access the appliance for servicing, select an easy-to-reach installation site.
- The surfaces of the appliance are sensitive. Avoid damaging them during installation.
16.8 Installation
Checking the ceiling
-
Check whether the ceiling is horizontal and ad- equately load-bearing.
The maximum weight of the appliance is 40 kg.
Do not fit the appliance directly onto plasterboard (or similar lightweight materials) in a suspended ceiling. -
Drill the hole depth in accordance with the length of the screws.
-
Install the appliance with a fixing material which is sufficiently stable and has been adjusted accordingly for both the structural conditions and the weight of the appliance.
-
Check the cut-out area for existing cables of other appliances.
Preparing the ceiling
- Cover the hob to prevent damage.
- Determine the position of the appliance and, thereby, the centre based on the position of the hob.
- Ensure that there are no electrical wires, gas pipes or water pipes in the area where holes are to be drilled.
- Drill four holes with a diameter of 6 mm for the fixing.
- Drill the hole depth in accordance with the length of the screws.
- Screw the fastening screws into the ceiling.
- Screw in the threaded rods.
- Screw the nuts approx. 10 mm onto the threaded rods.
Preparing the appliance
- Remove the grease filters. To avoid causing damage, do not bend the grease filters.
- Loosen the screws on the side covers.
- Open the odour filter cartridge.
- Push the side covers inwards and remove them.
- Close the odour filter cartridge.
Hanging the appliance
- Lift the appliance by the corners and turn it over.
- Position the cable that is provided on-site in the marked area on the appliance.
- Guide the cable that is provided on-site through the opening and hook the appliance into the fastening screws on the ceiling.
- Push the appliance as far as it will go into the four key hole openings using the guide sleeves.
- Move the appliance and lower it further so that the collar nuts are positioned on the edge of the guide sleeves.
- Carefully tighten the diagonally opposite collar nuts until the appliance is flush-mounted on the ceiling. Tighten the collar nuts one at a time so that the appliance does not tilt when doing so.
Connecting the appliance
Requirement: Ensure that the protection against contact is guaranteed during
installation.
-
Guide the cable that is provided on-site through the opening in the appliance.
Maintain the bending radius of the cable that is provided on-site for connecting the appliance.
The cable must remain doubly insulated. You should therefore strip the cable as little as possible upstream of the connecting terminal. -
Insert the on-site cable into the terminal plug.
Installing covers
WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.
-
Wear protective gloves.
Risk of injury when opening and closing the hinges. -
Keep your hands away from the hinges.
- Open the odour filter cartridge.
- Insert the side covers.
- Push the side covers in the direction of the appliance frame and screw them firmly in place.
- Remove the new odour filter from the packaging.
- Insert the odour filter into the odour filter cartridge. Insert the odour filter in the correct direction.
- Close the odour filter cartridge.
- Fit the grease filters.
To avoid causing damage, do not bend the grease filters.
Fitting the filter cover
WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.
-
Wear protective gloves.
Risk of injury when opening and closing the hinges. -
Keep your hands away from the hinges.
- Open the hinges on the filter cover.
- Mount the filter cover on the designated screws and push it backwards/forwards depending on the key hole opening into the narrow section.
- Tighten the fastening screws on the hinges.
- Swing the filter cover up and ensure that it engages.
- Connect the appliance to the power supply.
Removing the appliance
WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.
-
Wear protective gloves.
Risk of injury when opening and closing the hinges. -
Keep your hands away from the hinges.
The appliance is heavy. -
To move the appliance, two people are required.
-
Use only suitable tools and equipment.
-
Disconnect the appliance from the power supply.
-
Press the lock on the filter cover. To prevent the filter cover from swinging down suddenly, hold onto the filter cover firmly with two hands.
-
Open the filter cover by pulling it downwards.
-
Swing down the filter cover.
Open the filter cover fully and without pulling on it. -
Undo the screws on the hinges up to approx. 7 mm.
Do not loosen them fully. -
Unhook and remove the filter cover.
-
Remove the grease filters. To avoid causing damage, do not bend the grease filters.
-
Open the odour filter cartridge.
-
Remove the odour filter.
-
Loosen the screws on the side covers.
-
Remove the side covers.
-
Close the odour filter cartridge.
-
Loosen the cable that is provided on-site from the terminal clamp.
-
Carefully loosen the diagonally opposite screws.
-
Disconnect the appliance from the key hole opening.
-
Slowly take the appliance down.
BSH Hausgeräte GmbH
Carl-Wery-Straße 34
81739 München, GERMANY
www.gaggenau.com
Valid within Great Britain:
Imported to Great Britain by
BSH Home Appliances Ltd.
Grand Union House
Old Wolverton Road
Wolverton, Milton Keynes
MK12 5PT
United Kingdom
References
- www.me-connect.com
- Select your region | Gaggenau
- Gaggenau luxury Home Appliances for Kitchens | Gaggenau
- Connect your household | Home Connect