KandS KS PU1 Parallel Unit Instructions

KandS KS PU1 Parallel Unit

SAFETY INFORMATION

Do not use the device in conditions of excessive humidity, while standing in water or on moist soil (do not expose it to rain, snow). Do not expose the device to direct sunlight for a long time. Place the device on a flat, hard surface, away from flammable liquids/gases (at a minimum distance of 1 m). Keep unauthorized persons, children, and animals away from work area. Wear safety shoes and gloves.

ELECTRICAL SAFETY

WARNING – DANGER!

The device generates electricity. Observe safety precautions to avoid electric shock.

The device wiring diagram must comply with the installation rules and applicable regulations. Connect the device to the protective ground before operation using the terminal located on the device control panel. To avoid electric shock, do not use damaged wires as well as damaged or rusty contacts.

PLEASE NOTE!

Use the product for its intended purpose only. Using the device for purposes other than intended deprives the customer of a right to free warranty service.

WARNING – DANGER!

Do not operate the generator parallel connection box when you are tired or under the influence of potent drugs, narcotics or alcohol. Inattention during operation can cause serious injuries.

PARALLEL UNIT

KS PU1 generator parallel unit from Könner & Söhnen allows to increase the total output power of generators by connecting two inverter generators together. Parallel connection of any two generator models provides output power equal to the combined rated powers of these models. At the same time, parallel connection of generators entails a power loss of 0.2 kW of the aggregate rated power which can be obtained.

PLEASE NOTE!

The manufacturer reserves the right to make changes in the product design, configuration and construction. Illustrations in this manual are for reference only and may differ from actual components and inscriptions on the product.

Generator control panel

Generator parallel connection box

Cables

Each cable of the KS PU1 generator parallel connection box has three wires: red, black and yellow: The red wire is connected to the red connector on the generator control panel (“+” to “+”); the black wire is connected to the black connector on the generator control panel (“-” to “-”); and the yellow wire is connected to the ground terminal.

Voltage, V|

230

---|---
Sockets with protective covers|

1х16A

|

1х32A

Circuit breaker|

|

Maximum power, kW|

7

Cable length, cm|

2х80

Cable|

AWG 2.08 mm2

Prior to connecting the box to the generators, make sure the generators are turned off and power consumers are disconnected.

DEVICE OPERATION

1. Connect the wires of both cables of the parallel connection box to the corresponding connectors on the generator control panel.
2. Start the generator according to its operating instructions.
3. Connect the power consumers to the sockets of the KS PU1 generator parallel connection box.
4. Set the KS PU1 circuit breaker to “ON”.
5. Turn on the connected power consumers.

PLEASE NOTE!

Before connecting any power consumers to the box, make sure they are in good working order.

STOPPING THE GENERATOR

1. Turn off the connected power consumers.
2. Set the KS PU1 circuit breaker to “OFF”.
3. Disconnect the power consumers from the sockets of the KS PU1 generator parallel connection box.
4. Stop the generator according to its operating instructions.
5. Disconnect the wires of both cables of the parallel connection box from the connectors on the generator control panel.

WARRANTY SERVICE TERMS

TERMS AND CONDITIONS:

The international manufacturer warranty is 1 year. The warranty period starts from the date of purchase. In cases when warranty period is longer than 1 year according to local legislation please contact your local dealer. The Seller which sells the product is responsible for granting the warranty. Please contact the Seller for warranty. Within the warranty period, if the product fails because of defects in the production process, it will be exchanged on the same product or repaired.
The warranty card should be kept throughout the warranty period. In case of warranty card loss, a second one will not be provided. The customer must provide the warranty card and buyer`s check during request for repair or exchange. Otherwise, the warranty service will not be provided. The warranty card, attached to the product during sale, should be correctly and fully completed by the retailer and customer, signed and stamped. In other cases, warranty is not considered as valid.
Provide clean product to the service center. Parts, that must be replaced, are the property of the service center.

WARRANTY EXCLUSIONS:

• If the user has failed to comply with the instructions in this manual.
• If the product features damaged or missing identification stickers or labels, serial numbers, etc.
• If product malfunction was due to improper transportation, storage and maintenance.
• In case of mechanical damages (cracks, chips, impact and fall marks, deformation of housing, power cord, plug or any other components), including those resulting from the freezing of water (ice formation), provided there are foreign objects inside the unit.
• If the product has been improperly installed and connected to the mains supply or misused.
• If the claimed malfunction cannot be diagnosed or demonstrated.
• If proper operation of the product can be restored following cleaning from dust and dirt, appropriate adjustment, maintenance, oil change, etc.
• If the product is used for business related purposes.
• If faults are detected, which have been caused by product overload. Signs of overload are molten or discolored parts as a result of high temperatures, damaged cylinder or piston surfaces, degraded piston rings or connecting rod bushes.
• The warranty does not cover the failure of the product automatic voltage regulator due to careless handling or mishandling.
• If faults are detected, which have been caused by instability of the user’s power grid.
• If there are faults caused by contamination or fouling such as contamination of the fuel, oil or cooling system.
• If electrical cables or plugs show signs of mechanical or thermal damage.
• In the event of foreign liquids and objects, metal chips, etc. inside the product.
• If the malfunction is caused by the use of non-original spare parts and materials, oils, etc.
• If there are two or more faulty units that are not interconnected.
• If the damage was caused by natural factors such as dirt, dust, humidity, high or low temperature, natural disasters.
• To quick-wear parts and components (spark plugs, nozzles, pulleys, filter and safety elements, batteries, removable devices, belts, rubber seals, clutch springs, axles, manual starters, oils, gear).
• To preventive maintenance (cleaning, greasing, washing), installation and adjustment.
• If the product was tampered with, independently repaired or modified.
• In case of malfunctions resulting from normal wear and tear as a result of longterm use (end of life).
• If product operation was not stopped and continued after detecting a malfunction.
• Batteries supplied with equipment are covered by a warranty of three months.

CONTACTS

Deutschland:
DIMAX International GmbH
Deutschland, Hauptstr. 134,
51143 Köln,
www.ks-power.de
Ihre Bestellungen
orders@dimaxgroup.de
Kundendienst, technische Fragen
und Unterstützung
support@dimaxgroup.de
Garantie, Reparatur und Service
service@dimaxgroup.de
Sonstiges
info@dimaxgroup.de

References

• Домен припаркован в Timeweb
• Könner & Söhnen - генератори, садова техніка від виробника
• Könner & Söhnen Stromerzeuger ᐉ Generatoren k&s | Könner & Söhnen Notstromaggregat und Gartentechnik
• Könner & Söhnen generators and garden technology
• Könner & Söhnen | Generatory i Sprzęt Ogrodniczy

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>