SmartCell Sounder and Wall Beacon Installation Guide

SmartCell Sounder and Wall Beacon

Part number

SC-32-0110-0001-99 SC-32-0120-0001-99 SC-32-0210-0001-99 SC-32-0220-0001-99

Product description

• SmartCell RED Sounder and Wall Beacon (VAD RED Flash)
• SmartCell RED Sounder and Wall Beacon (VAD WHITE Flash)
• SmartCell WHITE Sounder and Wall Beacon (VAD RED Flash)
• SmartCell WHITE Sounder and Wall Beacon (VAD WHITE Flash)

Pre installation

• Installation must conform to applicable local installation codes and should only be installed by a fully trained competent person.
• The use of a non-metallic spacer should be considered if mounting the device on to a metal surface.
• This device contains electronics that may be susceptible to damage from Electrostatic Discharge (ESD). Take appropriate precautions when handling electronic boards.
• This device is suitable for wall mounting only. Ceiling mounted variants are also available.
• To ensure correct operation, products must be used within the specified environmental operating conditions.

Components

1. Sounder and wall beacon
2. Mounting plate
3. Batteries (not included in some regions*)

When batteries are not supplied, only fit specified batteries.

Remove mounting plate

• Remove the mounting plate by turning the device ANTICLOCKWISE, to release it from the mounting plate.

Fix mounting plate

• When fixing to the wall, all four fixing positions should be used to ensure a firm fixing.
• Where existing electrical mounting boxes are present, two fixing positions may be used.
• Use suitable fasteners and fixings.
• Observe the orientation marking!

Fit batteries

• When fitting / replacing batteries, observe correct polarity, using only specified batteries.

Configuration

The device must now be added (programmed) to the control panel.

• Refer to the programming manual for full programming details.
• SmartCell panel = TSD155
• SmartCell WZM = MK067

Optional device locking

• The device includes an optional locking mechanism.
• Remove the thin section of plastic shown below.
• Once locked, the Allen key will be required to unlock the device.

Completing the installation

• Reassemble the device as shown below.

Device unlocking

• If the device has been locked, an Allen key will be required for unlocking.
• Depress the locking mechanism, by inserting the Allen key, or similar, into the device’s cavity and pushing (A).
• Simultaneously twist the device anti-clockwise to release (B).

IMPORTANT

• The device should be tested upon installation, in accordance with local requirements.
• Testing should only be carried out by a fully trained competent person.

Specification

• Operating temperature -10 to +55 °C
• Storage temperature
  • With batteries -10 to +30 °C
  • Without batteries -10 to +55 °C
• Humidity 0 to 95% noncondensing
• Location Type B: for indoor/outdoor use
• IP rating IP33
• Supply 3 x ER14505M 3.6 V lithium thionyl chloride batteries (Fanso or Titus)

CAUTION!

• This is a life safety product. Only use manufacturer-approved battery types. Failure to do so may result in damage to the product.

• DO NOT mix batteries of different type or age.

• When replacing batteries; remove all old batteries before fitting replacements.

• Operating voltage 2.7 to 3.65 VDC

• Current consumption 0.32 A max.

• Power consumption 0.8 W max.

• Operating frequency 868 MHz

• Output transmitter power 14 dBm / 25 mW

• Signalling protocol X5

• Beacon flash rate 0.5 Hz (1 flash, every 2 seconds)

• Beacon coverage W-2.4-6 (WHITE flash) / W-3-5.11 (RED flash)

• Sounder output 95 dB(A) at 1m max.
  For full sounder output information, refer to the Sounder Data doc (MK103).

• Dimensions (Ø x D) 110 x 77 mm

Regulatory information

References

• My SmartCell | A New Innovation In Wireless Fire Detection
• HOME

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>