LIVING basics STE01 Digital Sterilizer and Dryer Instruction Manual

LIVING basics STE01 Digital Sterilizer and Dryer

FEATURE

• Model: STE01
• Voltage: 230V / 50 HZ
• Power Sterilizer : 600 W
• Diy: 180 W

PRODUCT PART

SPECIFICATION

CONTROL PANEL

• Press MODE to choose function:
  • Sterilize & Dry press 1x
  • Sterilize/Egg boil = press 2x
  • Dry press 3x
  • Warm Milk = press 4x
  • Warm Food press 5x
• • Press “START” to start the operation.
    • Press “CANCEL” to cancel function mode.

STANDARD TEMPERATURE / TIME

ADJUSTMENT TO TEMPERATURE AND TIME

If needed, some settings of temperature & time can be adjusted from the standard settings to accommodate a more specific needs.

• (+) Press “+”or “- ” to adjust time for Sterilize & Dry/ Dry/ Warm Food
• (-) Press “-” or “- ” to adjust the temperature for Warm Milk

OPERATION

Sterilize & Dry

1. Pour water 140ml into the machine base.

2. Place the sterilizer container on the machine base. Arrange washed bottles upside down (maximum 6 wide neck bottles / 12 standard bottles) inside the sterilizer container. Arrange the accessory rack on top and place the pacifier, a bottle cap, and other small units in the rack.

3. Plug in the power cable. Press “MODE” 1x to select “Sterilize & Dry”. The indicator light will light up on the “Sterilize” & “Dry” modes.
   Press “START to begin sterilizing and subsequent drying process. The indicator screen will show a rotating line indicating the machine is in operation. The sterilizing process will run for 14 minutes, then the machine will automatically proceed to dry for 30 minutes. After the drying process ends, the machine will beep 1x to indicate the entire operation is completed.

4. Drying time can be adjusted. Before press “The START button, press+ button to increase the time or “the ” button to reduce the time. The range of time settings is 1-120 minutes.

The machine will shut off when the water in the heating plate runs out and will continue to drying mode. The time needed for sterilizing process depends on the amount of water. For effective sterilization, use 140 ml of water for 14 minutes of sterilization.

Sterilize/ Egg boil

1. Pour water 140ml into the machine base.

2. Sterilize
   Place the sterilizer container on the machine base. Arrange washed bottles upside down(maximum 6 wide neck bottles / 12 standard bottles) inside the sterilizer container. Arrange the accessory rack on top and place the pacifier, bottle cap, and other small units in the rack.
   Egg boil
   Place the accessory rack on the machine base, then place eggs on the accessory rack and close it.

3. Plug in the power cable. Press “MODE” 2x to select “‘Sterilizer”. The indicator light will light up on the “Sterilizer” mode. Press “START” to begin sterilizing process. The indicator screen will show a rotating line indicating the machine is in operation. Sterilizing processes will run for 14 minutes, and the machine will beeps 1x when the entire operation is completed.

The machine will shut off when the water in the heating plate runs out. The time needed for sterilizing process depends on the amount of water. For effective sterilization, use 140 ml of water for 14 minutes of sterilization.

Dry

1. Place the sterilizer container on the machine base. Arrange washed bottles upside down (maximum 6 wide neck bottles / 12 standard bottles) inside the sterilizer container. Arrange the accessory rack on top and place the pacifier, bottle cap, and other small units in the rack.
2. Plug in the power cable. Press “MODE” 3x to select “Dry”. The indicator light will light up on the “Dry” mode. Press “START” to begin the drying process. The drying process will run for 30 minutes at 70 C. The machine will beep 1x when the entire operation is completed.
3. Drying time can be adjusted. Before press the “START” button, press+ button to increase the time or the “-” button to reduce the time. The range of time settings is 1 – 120 minutes.

Warm Milk

1. Pour water 140mi into the machine base.

2. Place the bottle tray on the heating plate. Arrange the sterilizer container on the machine base. Put the bottle on the tray, then close it.

3. Plug in the power cable. Press “MODE 4x to select “Warm Milk”. The indicator light will light up on the “warm Milk” mode.
   Press “START to begin the warming process. The indicator screen will show 45’C, and after 20 minutes the machine will beep 1x and the indicator light will flash indicating the heating process has been running for 20 minutes. The machine will continue to warm until it is stopped manually.

4. Warming time can be adjusted. Before press the “start button, press “+ button to increase the temperature or the button to reduce the temperature. Ihe range of temperature setting is 37 “C – 50 °C.

The length of time to warm milk depends on the initial temperature of the milk and the amount of milk.

Warm Food

1. Pour water 140ml into the machine base.

2. Place the accessory rack on the machine base, then place the bowl on the accessory rack and close it.

3. Plug in the power cable. Press “MODE 5x to select “Warm Food”. The indicator light will light up on the “Warm Food” mode.
   Press ‘s1ART to begin the warming process. he procesS Will run for b0 minutes at a maximum temperature of 80 “C or it ends when stopped manually. The machine will beep 1x when 600 minutes lapse.

4. Warming time can be adjusted. Before press, the “START” button, press the “+” button to increase the time or the button to reduce the time. The range of time settings is 5 – 80 minutes.

The machine will shut down when the water on the heating plate runs out. The length of time to warm food is depending on the first temperature of the food and the amount of food.

CLEAN AND CARE

1. Do not immerse the machine base in water. Just wipe/ dry with a clean cloth.
2. Other parts can be washed/rinsed with soap and water.
3. Crusty heating plate can be cleaned by using vinegar and drinking water.
4. Pour a mixture of 40 ml vinegar and 80 ml drinking water into the heating plate.
5. Do not cover the machine.
6. Press mode “Sterilizer”. After sterilizing process is complete, throw away the remaining mixture.
7. Pour drinking water into the heating plate then process sterilization again.
8. Repeat this step twice to remove any remaining vinegar on the heating plate.
9. Last, clean the heating plate with a dry cloth.

NOTES

• This product has a thermostatic control system. If no water on a heating plate or runs out of water, the machine will automatically shut off even though the process has not been completed. Pour water 140 ml into the machine base in accordance to instructions.
• The 140 ml amount of water can be used for the duration of:
  • Sterilization: 14 minutes.
  • Warm food: 60-80 minutes.
  • Warm milk: nonstop.

CAUTION

• When the engine heats up, steam will come out of the lid hole. Do not cover the holes and do nottouch it.
• Do not immerse the machine in water to avoid short circuit. Simply clean it with a cloth.
• It is recommended to use drinking water (not tap water) to operate the machine.
• Do not pour milk / food directly into the machine base without using food container.
• This machine is not suitable to be operated by children and people with mental disabilities.
• This machine is designed for household purpose only.
• Do not touch the heating plate when it is still hot,

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>