Whirlpool WHS1021 Freestanding Freezer Instructions Manual

Whirlpool WHS1021 Freestanding Freezer

DESCRIPTION AND USE

DIAGRAM OF THE APPLIANCE

1. Lid
2. Lock (if provided)
3. Seal
4. Defrost water drain plug (depending on model)
5. Control
6. Basket (depending on model)
7. Condenser (located at the rear)

INSTALLATION

• Refer to the chapter “Before using the appliance”.
• Unpack the appliance.
• Remove the 4 protection pieces inserted between the lid and the appliance

Warning: two of the four protection pieces must be fitted in the seat of the condenser plastic supports, located at the rear of the product. This is necessary to ensure the correct distance from the wall.

• Ensure that the defrosting water drainage plug (if provided) is correctly positioned ( 4 ).
• For the best operation of the appliance and in order to avoid damage when the lid is opened, leave a space of at least 7 cm from the rear wall and 7 cm at the
• Fit the accessories (if provided).

Clean the inside of the appliance before using it.

DIAGRAM OF THE CONTROL PANEL

• Red LED: when flashing, it indicates that an alarm condition is present see TROUBLESHOOTING GUIDE”
• Green LEDS: they indicate that the appliance is in operation, and the temperature has been set as follows:
  • b1 less cold temperature (right light on), using this setting with partial loads will optimize energy consumption.
  • b2 middle temperature (center light on)
  • b3 very cold temperature (left light on)

ALL Green LEDs ON: FAST FREEZING function is active; see the section “freezing fresh food”.

1. Temperature setting button: to adjust the set temperature and to activate/deactivate the fast freezing operations.
   • To select the desired temperature, repeatedly press the setting button (3): each time the button is pressed, the set temperature is updated.
   • To activate/deactivate the fast freezing function, press for approximately 3 seconds: all green LEDs flash simultaneously 3 times and then remain lit.

Note: The settings will be saved in the memory even if a power cut occurs. The time needed for the temperature inside the freezer to reach the set value can vary depending on climatic conditions and the set temperature itself.

Switching on the appliance

• Plug in the
• The green LED lights up (middle temperature).
• The red LED flashes to indicate that the temperature inside the appliance is not yet sufficiently low for food storage. The red LED will normally switch off within the first six hours after the appliance is switched on.
• Place food inside the product only when the red LED has been switched off.

Note: As the seal is tight, the appliance lid cannot be reopened immediately after closing. Wait a few minutes before re-opening the lid of the appliance.

FREEZING FOOD

Preparation of fresh food for freezing

• Before freezing, wrap and seal fresh food in Aluminium foil, cling film, air, and water-tight plastic bags, and polyethylene containers with lids, provided they are suitable for freezing foods.
• Food must be fresh, mature and of prime quality in order to obtain high-quality frozen food.
• Fresh vegetables and fruit should preferably be frozen as soon as they are picked to maintain the full original nutritional value, consistency, color and
• Always leave hot food to cool before placing it in the

Freezing fresh food

• Place foods to be frozen in direct contact with the walls of the appliance

1. foods to be frozen,
2. foods already

• Avoid placing foods to be frozen in direct contact with food already frozen.
• For best and fastest freezing, foods should be split into small portions; this will also be useful when the frozen items are to be used.

1. At least 24 hours before storing fresh foods inside the product for freezing, activate the fast freezing function by pressing button c for approximately 3 seconds. All green LEDs ( b ) come on.
2. Introduce the food to freeze inside the appliance, and keep the door of the appliance closed for 24 hours. After this period the food will be frozen. The fast freezing function can be deactivated by pressing button c for approximately 3 seconds. If the fast freeze function is not manually deactivated, it will be automatically deactivated by the appliance after 50 hours.

FOOD STORAGE

Refer to the table on the appliance. Classification of frozen foods

Put the frozen products into the appliance and classify them; the storage date should be indicated on the packs, to allow use within expiry dates listed in months in for each type of food.

Advice for storing frozen food

When purchasing frozen food products:

• Ensure that the packaging is not damaged (frozen food in damaged packaging may have deteriorated). If the package is swollen or has damp patches, it may not have been stored under optimal conditions, and defrosting may have already begun.
• When shopping, leave frozen food purchases until last and transport the products in a thermally insulated cool bag.
• Once at home, place the frozen foods immediately in the appliance.
• Avoid, or reduce temperature variations to the minimum Respect the best-before date on the
• Always observe the storage information on the

Note: Eat fully or partially defrosted foods immediately. Do not refreeze unless the food is cooked after it has thawed. Once cooked, the thawed food can be refrozen.

If there is a long power failure:

• Do not open the appliance lid except to place ice packs (if provided) over the frozen foods on the right and left of the This will slow down the rise in temperature.

DEFROSTING THE APPLIANCE

The appliance should be defrosted when the thickness of ice on the walls reaches 5-6 mm.

• Disconnect the appliance from the mains power
• Remove the packs of food from the appliance and wrap them close together in newspaper and store them in a very cool place or thermally insulated bag.
• Leave the appliance lid
• Remove the internal defrost water drain plug (depending on the model)
• Remove the external defrost water drain plug (depending on the model) and reposition it as shown in figure 6.
• Place a bowl beneath the drainage channel to collect the residual If available, use the divider.
• Speed up defrosting by using a spatula to detach the ice from the appliance walls.
• Remove the ice from the bottom of the
• In order to avoid permanent damage to the appliance interior, do not use pointed or sharp metal instruments for removing the ice.
• Do not use abrasive products or heat up the interior
• Dry the interior of the appliance
• On completion of the defrosting, refit the

CARE AND MAINTENANCE

• Remove the ice from the upper edge (see the Troubleshooting Guide).
• Clean the inside after defrosting, using a sponge dampened with warm water and/or mild
• Clean the side motor cooling grille (depending on the model).
• Remove dust from the condenser on the rear of the

Before carrying out maintenance, unplug the appliance. Do not use abrasive products, scourers, or stain-removers (e.g. acetone, trichloroethylene) to clean the appliance. To obtain the best results from your appliance, carry out cleaning and maintenance at least once a year.

**CHANGING THE LID LIGHT BULB (if provided)**

• Disconnect the appliance from the mains power
• Remove the diffuser by following the sequence of steps shown in figure 7.
• Unscrew the light bulb and replace it with an identical bulb of the same wattage and
• Refit the diffuser and plug in the

TROUBLESHOOTING GUIDE

1. The red LED flashes.

   • Is there a power failure?
   • Is a defrosting operation in progress?
   • Is the appliance lid properly closed?
   • Is the appliance placed near a heat source?
   • Are the ventilation grille and condenser clean?

2. All LEDs flash at the same time.

   • Contact the After-Sales

3. The appliance is too noisy.

   • Is the appliance perfectly horizontal?
   • Is the appliance in contact with other furniture or objects that may cause vibrations?
   • Has the packaging been removed from under the appliance?
     Note: Gurgling noises from the refrigerating circuit after the compressor cuts out are perfectly normal.

4. All LEDs are off and the product is not working.

   • Is there a power failure?
   • Is the plug properly inserted in the socket?
   • Is the electric cable intact?

5. All LEDs are off and the product is working.

   • Contact the After-Sales

6. The compressor runs continuously.

   • Have hot foods been put in the appliance?
   • Has the appliance lid been left open for a long time?
   • Is the appliance placed in a very warm room or near heat sources?
   • Has the fast freeze function been activated? (All Green LEDs ON)

7. Too much ice on the upper edge.

   • Are the defrost water drainage plugs correctly positioned?
   • Is the appliance lid properly closed?
   • Is the appliance lid seal damaged or deformed? (See chapter “Installation”)
   • Have the 4 protection pieces been removed? (See chapter “Installation”)

8. Formation of condensate on the external walls of the appliance.

   • It is normal for condensation to form under certain atmospheric conditions (humidity above 85%) or if the appliance is located in a damp or poorly ventilated The performance of the appliance is in no way affected.

9. The layer of ice on the internal walls of the appliance is not uniform.

   • This phenomenon is quite

AFTER-SALES SERVICE

Before contacting After-Sales Service:

1. See if you can solve the problem
2. Switch the appliance on again to see if the problem has been If it has not, disconnect the appliance from the power supply and wait for about an hour before switching on again.
3. If the problem persists after this course of action, contact After-Sales Service.

Specify

• the nature of the fault
• the model
• the service number (the number after the word SERVICE on the rating plate on the rear of the appliance)
• your full address
• your telephone number and area

ELECTRICAL CONNECTION FOR GREAT BRITAIN AND IRELAND ONLY

Warning – this appliance must be earthed. Fuse replacement

If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows:

1. Remove the fuse cover ( A ) and fuse ( B ).
2. Fit replacement 13A fuse into the fuse
3. Refit both into

Important

• The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted.
• Correct replacements are identified by the color insert or the color embossed in words on the base of the plug.
• Replacement fuse covers are available from your local electrical store.

For the Republic of Ireland only

• The information given in respect of Great Britain will frequently apply, but a third type of plug and socket is also used, the 2-pin, side earth type.

Socket outlet/plug (valid for both countries)

• If the fitted plug is not suitable for your socket outlet, please contact After-sales Service for further instructions.

FAQ’s

What is the temperature of a Whirlpool freezer?

33°F to 45°F (0°C to 7°C) is the refrigerator’s set point range. The freezer’s set point range is between -5°F and 5°F (-21°C and -15°C).

What occurs when a freezer gets too chilly?

The defrost heater might not work properly if the freezer is too chilly. When this component of the system malfunctions, the freezer is unable to keep frost from building up. Other issues will arise from a defrost heater that is damaged or not working properly.

If a freezer is full, is it colder?

A full freezer keeps it cold longer than one that is empty.

What triggers a fridge to run nonstop?

The freezer door or lid gasket is one of the most frequent causes of a freezer that runs continually.

How long is the lifespan of a Whirlpool refrigerator/freezer?

The average refrigerator is made to last 10 to 20 years.

How frequently should I defrost my Whirlpool freezer?

Roughly once every ten hours.

How long does a Whirlpool freezer take to become cold?

It is advised that you give your Whirlpool refrigerator 24 hours to reach full performance if it was just installed.

How can I get my Whirlpool freezer to freeze more quickly?

24 hours before to packing a freezer compartment with a lot of fresh food, press the button.

How long can freezers operate without electricity?

Food in a refrigerator will remain safe for up to 4 hours if the doors are kept closed. 48 hours in a fully-stocked freezer and 24 hours in a partially- stocked freezer.

What setting ought to be used for my Whirlpool chest freezer?

The ideal freezer temperature to keep your food safe is at or below 0°F (-18°C), although depending on its environment and other circumstances, your freezer may need to be set higher or lower. The standard 0°F (-18°C) freezer factory setting on Whirlpool® refrigerators is a wonderful place to start.

The Whirlpool chest freezer needs to be reset.

Turn off the circuit breakers in your home and/or unplug your refrigerator for five to ten minutes to reset the electricity to your Whirlpool freezer.

In a Whirlpool freezer, where is the thermostat located?

In the freezer area, the defrost thermostat is concealed behind the back panel.

What freezer temperature is the coldest?

The following guidelines apply to the coldest settings on every refrigerator: The refrigerant power is shown by the numbers on the refrigerator’s temperature dial. The refrigerator will maintain a cooler temperature as the number rises. Your refrigerator will be the coldest when you set it to 5.

Why isn’t the fridge in my Whirlpool cooling?

The most frequent reason for a Whirlpool refrigerator not cooling is dirty condenser coils. As the refrigerant flows through the condenser coils, heat is released from them. The coils cannot effectively discharge the heat if they are covered in dirt and debris.

How can I get my Whirlpool freezer to freeze more quickly?

24 hours before to packing the freezer with a lot of fresh food, press the button.

Download this PDF Link:Whirlpool WHS1021 Freezer Instructions Manual

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>