equip 650602 90 Degree Rotate Single Display 37-70 Inch TV Cart User Manual
- June 4, 2024
- equip
Table of Contents
- equip 650602 90 Degree Rotate Single Display 37-70 Inch TV Cart
- Package M
- Assembling the Base
- Attaching the Column to the Base
- Installing the Support Plate
- Installing the Adapter Brackets
- Hooking the Display onto the Support Plate
- Installing the DVD Shelf
- Cable Management
- Installing the Camera Shelf
- Installing the Connecting Plate
- Display Orientation
- Adjustment
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
equip 650602 90 Degree Rotate Single Display 37-70 Inch TV Cart
Read the entire instruction manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings,
please contact local distributor for assistance.
CAUTION:
Use with products heavier than thee rated weights indicated may result in
instability causing possible injury.
- Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
- Satety gear and proper tools must be used. I his product should only be installed by professionals.
- This product is designed to be installed on wood stud walls, solid concrete walls or brick walls.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- IMPORTANT: Ensure that you have received all pats according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
- MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals (at least every three months).
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
- Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
- This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
- Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
- Tighten screws firmly, but do not over lighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
Assembling the Base
- Insert the right leg into the base. Align the holes in the right leg to the holes in the base. Secure with the screws. Repeat this step for the left leg.
- Each castor can be adjusted independently for fine tuning. Slightly turn the nut to lower or raise the base.
Attaching the Column to the Base
Attach the column to the base using the screws .Tighten all screws using an Allen key .
Installing the Support Plate
Installing the Adapter Brackets
Attach the two plastic covers to both ends of the plate using the appropriate screws. Tighten all screw using a suitable screwdriver.
Adjust the adapter brackets to fit the hole pattern of your display. Then tighten all screws with an Allen key. NOTE: Verify the proper alignment of all holes.
4-1 For Flat Back Screens
4-2 For Recessed Back Screens or to Access A/V Inputs
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen. Screw the adapter brackets onto the display. Tighten all screws but do not over tighten.
Hooking the Display onto the Support Plate
- Hook the universal plate onto the support plate.
- Tighten two screws to secure them.
IMPORTANT: Make sure the display is mounted correctly, and that the screws are tightened safely before releasing the display.
Installing the DVD Shelf
Cable Management
Installing the Camera Shelf
Installing the Connecting Plate
Display Orientation
Adjustment
Maintenance
- Check that the bracket is secure and safe to use at regular intervals(at least every three months).
- Please contact your distributor if you have any questions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>