563H Plus Blumotion Heavy Duty Full Extension Concealed Runners Instruction Manual

563H Plus Blumotion Heavy Duty Full Extension Concealed Runners

Heavy duty full extension concealed runners

Basic components

Locking devices

Runners

Side-to-side adjustment

1. Rotate side-to-side adjustment left or right equally on both locking devices. Drawer front moves in the same direction as rotation.
2. After front side-to-side adjustment is made with the locking devices, rotate the rear side-to-side adjustment left or right to re-align the back of the drawer box with the front. Drawer back moves in the same direction as rotation.

Height adjustment

1. Press up on adjustment tab
2. Push towards back of drawer

Maximum 3 (1/8″) rise of drawer front (tool-free)

NOTE : Height and tilt adjustments available with all combinations of locking devices and runners

Tilt adjustment
Rotate the tilt adjustment lever on the rear of each runner to lift the back of the drawer and tilt the top of the drawer front forward

Depth adjustable locking device
Locking device with side-to-side, height and depth adjustment

Turning the adjustment screw allows for up to a +2.5 (3/32″) out adjustment

NOTE: For T51.1901.PS setback in inset applications, see page 5

Depth adjustment on runner
TANDEM 569 runners feature elongated holes that allow ±4.5 (3/16″) depth adjustment

Drawer box specifications

NOTE : Drawer side material thickness may vary. Accurate measurement of drawer side material thickness should be used when calculating outside drawer width using the table below. Inside drawer width must equal opening width minus 42 (1-21/32″) for TANDEM to align and function optimally.

Drawer insertion
Extend the concealed runners fully. Place the drawer on the runners and close. The locking devices automatically engage with the runners. Make adjustments if necessary.

Drawer back preparation

NOTE : Use of the T65.1600.01 TANDEM template is essential for accurate location and angle of pre-bored locking device holes and accurate boring for rear hook holes

Preparing for hardware installation

``Drawer removal

1. Squeeze orange handles on locking devices
2. Pull drawer straight out and up

Runner mounting specifications

Side view

NOTE: Orange dots indicate screw locations required to meet specified load capacities

Cabinet and drawer specifications

Side view

TANDEM plus BLUMOTION| Cabinet depth| Inside cabinet depth| Drawer length| Maximum drawer thickness| Runner length
---|---|---|---|---|---
Minimum
569.7620B| 838 (33″)| 786 (30-15/16″)| 762 (30″)|

16 (5/8″)

| 777 (30-19/32″)
569.6860B| 762 (30″)| 709 (27-29/32″)| 686 (27″)| 700 (27-9/16″)
569.6100B| 686 (27″)| 634 (24-31/32″)| 610 (24″)| 625 (24-19/32″)
569H5330B| 610 (24″)| 557 (21-15/16″)| 533 (21″)| 548 (21-9/16″)
569H4570B| 533 (21″)| 480 (18-29/32″)| 457 (18″)| 471 (18-17/32″)
NOTE: For heavy duty applications, rear brackets and sockets cannot be used. Cabinet sides must be blocked-out flush with the inside of the frame.
T51.1901R| Locking device with side-to-side adjustment (right)
---|---
T51.1901L| Locking device with side-to-side adjustment (left)
T51.1801R| Locking device (right)
T51.1801L| Locking device (left)
606N or 606P| #6 Wood screw (for mounting runner to cabinet side, rear brackets and locking devices)
662.1150.HG| #6 System screw (for mounting runner to cabinet side)

Face frame application — complete blockout

Side view

Frameless application

Side view

``

Setback information

Side view

NOTE : For mounting hole position add 7 (9/32″) to runner setback

Runner setback when using depth adjustable locking device (T51.1901.PS)

Drawer front thickness
Calculating runner setback|

563/569 H/.

|

• Setbacks in this table recess the face of the drawer front inside of the cabinet 1 (1/32″)
• The depth adjustment can then be used to move the drawer front out to its desired position, 2.5 (3/32″) out adjustment only

Runner setback when using all other locking devices

• Setbacks in this table set the face of the drawer front flush with the face of the cabinet
• If a depth adjustable locking device is needed, please see the locking device and table above

Attachment Specifications

Depth adjustment specifications

Side view

Mount each runner using at least two of the elongated holes. Install the drawer to check the position of the drawer front. Remove the drawer, loosen screws and make adjustments if necessary, ±4.5 (3/16″). Tighten the screws, verify the drawer front position and finish mounting the runners using the screw locations indicated by the orange dots.

TANDEM plus|

A

|

B

|
---|---|---|---
BLUMOTION
569.7620B| 244.5 (9-5/8″)| 372.5 (14-21/32″)|
569.6860B| 244.5 (9-5/8″)| 372.5 (14-21/32″)|
569.6100B| 244.5 (9-5/8″)| 372.5 (14-21/32″)|
569H5330B| 244.5 (9-5/8″)| 500.5 (19-23/32″)|
569H4570B| 244.5 (9-5/8″)| 436.5 (17-3/16″)|

Subject to technical modifications wit hout notice. © 2016 Blum Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>