AVTEDU629 Raging LED Bull DIY Kit for Learning Soldering Instruction Manual
- June 8, 2024
- AVT
Table of Contents
AVTEDU629 Raging LED Bull DIY Kit for Learning Soldering
Don’t blow in this bull’s nose – you’ll only make him angry!
When it’s quiet and still, the LED diodes are off, but blowing air into the
bull’s nose, or giving it a flick, will turn the diodes bright red.
Thankfully, when the bull’s anger simmers down, so do LED diodes gradually,
fluidly dim.
The brightness of the diodes depends on the loudness of detected sound.
Specifications
- two red LED diodes
- microphone (sound sensor)
- potentiometer regulating the bull’s anger
- power switch
- dimensions of the circuit board: 74×66mm
- power supply: 9VDC [6F22] – battery not included
Figure 1. Schematic diagram
Figure 2. Position of the elements on the printed circuit board
Suggested order of assembly
- R1: ……………………….10kΩ (brown-black-orange-gold)
- R2: ……………………….1kΩ (brown-black-red-gold)
- R3: ……………………….1MΩ (brown-black-green-gold)
- R4: ……………………….100Ω (brown-black-brown-gold)
- R5: ……………………….100kΩ (brown-black-yellow-gold)
- R6: ……………………….4,7kΩ (yellow-violet-red-gold)
- R7: ……………………….220Ω (red-red-brown-gold)
- Z:………………………….0Ω (black)
- D1:……………………….1N4148 !
- C1: ………………………100uF !
- C2: ……………………….10uF !
- C3: ……………………….100n (may be marked as 104)
- C3: ………………………220n (may be marked as 224)
- T1:………………………..BC548 !
- PR1:……………………..potentiometer 1MΩ
- LED1, LED2:………..5mm red LED diode
- U1:……………………….LM358 + IC socket!
- SW1: ……………………switch
- MIC1:…………………..microphone
- battery connector: red-positive Ĺ, black-negative ⊝
Begin by soldering the elements onto the circuit board in order from smallest
to largest.
When assembling the elements marked with “!” pay attention to their polarity
and placing of the notch battery connector: red-positive Ĺ, black-negative
⊝
Assembly instructions
- Touch the tip of the soldering iron to the end of the element near the soldering field
- Next, apply tin solder
- After the cone forms, remove tin solder first, and then the soldering iron
- The whole process should take approx. 2-3 seconds.
The cleanness of the soldered surfaces, right amount of flux in the solder,
adequately high temperature (320-360°C), and sufficient amount of solder are
necessary to complete a correct bonding.
Too much tin solder can result in forming a ball instead of a cone or joining
of two adjacent soldering points.
Inadequate temperature, amount of tin solder or impurities can lead to so
called “cold solder joints, i.e. solder and the flux can’t moisten the two
surfaces and the resulting solder point is fragile and in time will oxidize,
break, and stop working.
Thank you for purchasing AVT product. Please take your time to read carefully
the important information below concering use of this product.
Educational Electronics Kits are intended for educational and demonstration
purposes only. They are not intended for use in commercial applications. If
they are used in such applications the purchaser assumes all responsibility
for ensuring compliance with all local laws. In addition, they cannot be used
as a part of life support systems, or systems that for use as or as a part of
life support systems, or systems that might create a hazardous situation of
any kind.
- Battery or wall-adaptor are safe devices. They do not require special attention unless main voltage is connected to an output e.g. a relay.
- If the kit is used to switch currents greater than 24V it is necessary to have the installation and performed by a trained professional authorized for such work. The kit may only be used in such application if it was installed in a safe to touch enclosure.
- Never exceed the limits or ratings listed in the ‘Specifications’ section at the this user guide.
- If the kit is used in schools or educational facilities or similar institutions the operation must be supervised by trained and authorized staff.
- The product itself and all parts thereof (including packing material) are not suitable toys for childern! (choking hazard, risk of electric shock, …)
Failures in modern electronic component are very rare as 95% of non-working kits are due to poor soldering or components placed in the wrong location or orientation so please check your work carefully.
AVT SPV Sp. z o.o.
Leszczynowa 11 Street, 03-197 Warsaw, Poland http://avtkits.com/
This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment.
AVT SPV reserves the right to make changes without prior notice.
Assembly and connection of the device not in accordance with the instructions,
unauthorized modification of components and any structural modifications may
cause damage to the device and endanger the person using it. In this case, the
manufacturer and its authorized representatives shall not be liable for any
damages arising directly or indirectly from the use or malfunction of the
product.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>