GLOBBER Flow Foldable Scooter Owner’s Manual
- June 8, 2024
- GLOBBER
Table of Contents
www.globber.com
THE WORLD ON WHEELS
FLOW • FOLDABLE
OWNER’S MANUAL
Flow Foldable Scooter
| **** | **** |
|---|
Keep the instructions for future.
NF-EN-14619:2019
READ THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER BEFORE USING. MAXIMUM
WEIGHT: 100 KG
Warnings
- The Scooter is suitable for adolescents and adults. It is not a toy, but sports equipment for physical training, it is not intended for use in extreme sports such as jumping, ollie ramps, etc. This product should never be used at a skate park for an “aggressive” use (challenging skateboarding moves, etc.).
- Use with caution on a flat, clean, dry surface and, if possible, away from other users, and obey the road safety rules.
- Check local laws regarding scooter use, respect all the traffic rules and signs. Stay away from other pedestrians or users on public roads.
- Best when used on a flat, dry surface free of gravel and grease. Avoid bumps and drainage grates that might cause an accident.
- Warning! Protective equipment consisting of wrist protectors, gloves, knee pads, helmets and elbow pads should be worn.
Using the scooter
- Before and after each use: To prevent pinched fingers, carefully follow the instructions of unfolding and folding. Make sure that the locking mechanisms are securely locked:
- Check the height of the steering system and make sure that the nuts are tightened and the handlebars and front wheel are perpendicular.
- Check all of the connection elements: the brake, the quick release system of the steering column and the wheel axles must be correctly adjusted and must not be damaged.
- Also check the tire wear.
- Braking:
- A brake is located at the rear, when necessary, press down on it to slow down. Press down gradually to prevent skidding or loss of stability. The metal brake may heat up after multiple uses. Avoid touching it during and after use.
During use:
- Standing on the scooter, with one hand on each handle, push with one of your feet to move forward. Proceed with caution at the start.
- Always wear shoes and we strongly recommend wearing pants and long sleeve shirts to avoid injury if you fall.
- The scooter does not include any headlights or lights. It is therefore not suitable for use at night or during periods when visibility is limited.
- Do not use on wet days, or on wet ground.
Assembling the product
- The folding and unfolding operations of the scooter are to be done by a single person.
- During these operations, be careful you do not get your fingers stuck in the hinge and locking system.
- Make sure that the locking devices are properly engaged.
Assembling the handlebar (see page 2)
Insert the handlebar into the stem of the fork while paying attention to the
position of the base. The vertical part of the fork should be at the front and
the wide part of the mudguard should be at the back. Tighten the screws on the
clamp and make sure they are fully screwed into the hole.
UNFOLD & FOLD THE SCOOTER SAFELY (See page 3)
Press the button on the front of the deck. Unfold the handle and front wheel
upwards until the automatic lock secures the T-bar handle in upright position.
Vice versa if you want to fold the scooter.
Trolley mode: You can grip the scooter by the T-bar handle and pull it behind
you for easy transport.
Warning! Risk of injury by pinching!
Do not insert your fingers into the shaded area indicated.
Adjust the height
Open the quick lock and pull the steering column until the bullet get into the
hole then tighten the quick lock. To adjust the tightness of the quick lock,
tighten or loosen the screw.
4 Positions :
- Low position: 80.5 cm
- Middle position: 85.5 / 90.5 cm
- High position: 95.5 cm
DO NOT FORGET TO REGULARLY TIGHTEN ALL BOLTS AND SCREWS TO AVOID
MISALIGNMENT OR LOSS OF THE SCREW.
Care / Maintenance: regular maintenance is a safety commitment;
- Wheel bearings: avoid going through water, oil or sand as this can damage wheel bearings. To look after the wheel bearings, systematically check that the wheels turn properly by turning the scooter upside-down and using your hand to spin the wheels. If the wheels do not spin they must be removed to check their condition. First unscrew the wheel axle, remove the axle and detach the wheel, then carefully push the two wheel bearings out of their housing. If they are chipped or dented, new ones should be bought. If there is no visible damage, they must then be oiled. To do this, remove all traces of grease, mud or dust with a kitchen towel or cloth, and re-oil them with a grease spray or by leaving them to soak overnight in oil [turn them several times in the oil first]. Then reassemble the wheel bearings and axles, followed by the wheel, onto the scooter. Proceed in the same manner for the other wheel.
- Wheels: the wheels wear down with time and can be pierced if overly used on rough surfaces. The back wheel on which the brake is applied is particularly affected after several hours of braking. In the interests of safety, they should be checked regularly and changed if necessary.
- Modifications: the original product must by no means be modified except for the maintenance-related changes mentioned in these instructions.
- Nuts, axles and other self-locking fixings: these should also be checked regularly. They can become loose after a while in which case they should be tightened. They can become worn and not tighten properly, in which case they should be replaced.
Additional Info
For questions and inquiries please contact us at:
contact@globber.com
WARRANTY
The manufacturer warranties this product to be free of manufacturing defects
for period of 2 years from date of purchase.
This limited Warranty does not cover normal wear and tear, tire, tube or
cables, or any damage, failure or loss caused by improper assembly,
maintenance, or storage.
This Limited Warranty will be void if the product is ever
- used in a manner other than for recreation or transportation;
- modified in any way;
- rented
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
Globber does not offer an extended warranty. If you have purchased an extended
warranty, it must be honoured by the store at which it was purchased.
For your records, save your original sales receipt with this manual and write
the product name below.
Spare parts
To order spare parts for this product, please visit our website
www.globber.com
Class A / Classe A
100KG MAX
NF EN 14619:2019
www.globber.com
ID DEVELOPMENT LIMITED
Room 1302, 13/F, Chevalier House,
45 – 51 Chatham Road South,
Tsim Sha Tsui, Kowloon, Hong Kong
GLOBBER FRANCE SAS
66 rue de l’industrie
01120 Montluel – France
Ref.: 473
Made in China
IM_473_31L_2201