LG Uplus IoT DoorCam DCH-01 Manual
- June 8, 2024
- LG Uplus
Table of Contents
- LG Uplus
- IoT DoorCam
- SKU: DCH-01
- Quickstart
- Important safety information
- What is Z-Wave?
- Product Description
- Prepare for Installation / Reset
- Inclusion/Exclusion
- Quick trouble shooting
- Association – one device controls an other device
- Technical Data
- Supported Command Classes
- Explanation of Z-Wave specific terms
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LG Uplus
IoT DoorCam
SKU: DCH-01
Quickstart
This is a
secure
On/Off Power Switch
for
South Korea.
Please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
This must be done when the DoorCam is in an excluded status, which means that
it is not a part of any Z-Wave network; you will know this because the Z-Wave
LED will remain on.After starting the inclusion process on your Z-Wave
controller, please do the following:a. Press & hold the Z-Wave inclusion
button for 5 seconds.b. When the Z-Wave LED blinks rapidly, release the Z-Wave
inclusion button.c. The DoorCam will try inclusion for 30 seconds.d. If
inclusion was successful, the Z-Wave LED will turn off.
Please refer to the
Manufacturers
Manual
for more information.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in
this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any
loss or damage resulting from failure to comply with the instructions in this
manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal
instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart
Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message ( two-
way
communication) and every mains powered node can act as a repeater for other
nodes
( meshed network ) in case the receiver is not in direct wireless range of
the
transmitter.
This device and every other certified Z-Wave device can be used together
with any other
certified Z-Wave device regardless of brand and origin as long as both are
suited for the
same frequency range.
If a device supports secure communication it will communicate with other
devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to
maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc.
please refer
to www.z-wave.info.
Product Description
LG Uplus IoT DoorCam streams live video feed to your phone remotely. The app receives push notifications of different activities and record motion videos when visitors arrive. It also checks the battery life with the app and receives reminders when the battery is low.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory
default
state. Please make sure to reset the device into factory default. You can do
this by
performing an Exclusion operation as described below in the manual. Every
Z-Wave
controller is able to perform this operation however it is recommended to use
the primary
controller of the previous network to make sure the very device is excluded
properly
from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave
controller. This
procedure should only be used when the primary controller is inoperable.
a. Hold the Z-Wave button for 10 seconds.(Z-Wave LED will blink after 5 seconds with 250ms interval then Z-Wave LED will be turned off after another 5 seconds.)b. When Z-Wave LED stops blinking after 10 seconds, release Z-Wave button.c. When factory reset is successful, LED will be on.Please use this procedure only if the network primary controller is missing or inoperable.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The
device needs
to be added to an existing wireless network to communicate with the
devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called
Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network.
This
controller is turned into exclusion respective inclusion mode. Inclusion and
Exclusion is
then performed doing a special manual action right on the device.
Inclusion
This must be done when the DoorCam is in an excluded status, which means that it is not a part of any Z-Wave network; you will know this because the Z-Wave LED will remain on.After starting the inclusion process on your Z-Wave controller, please do the following:a. Press & hold the Z-Wave inclusion button for 5 seconds.b. When the Z-Wave LED blinks rapidly, release the Z-Wave inclusion button.c. The DoorCam will try inclusion for 30 seconds.d. If inclusion was successful, the Z-Wave LED will turn off.
Exclusion
This must be done when the DoorCam is in an included status, which means that it is a part of any Z-Wave network; you will know this because the Z-Wave LED will remain off.After starting the exclusion process on your Z-Wave Controller, please do the following.a. Press & hold Z-Wave button for 5 seconds when DoorCam is inclusion status.b. When Z-Wave LED blinks with 250ms interval, Release Z-Wave button to try exclusion.c. DoorCam will try exclusion for 30sec.d. Z-Wave LED will be turned on if exclusion is successful.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association – one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one
device
controlling another device is called association. In order to control a
different
device, the controlling device needs to maintain a list of devices that will
receive
controlling commands. These lists are called association groups and they are
always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’
Command.
Association Groups:
Group NumberMaximum NodesDescription
1 | 1 | This product’s Association Group are used by Life Line of products. |
---|
Technical Data
Hardware Platform | ZM5101 |
---|---|
Device Type | On/Off Power Switch |
Network Operation | Listening Sleeping Slave |
Firmware Version | HW: 1 FW: 39.58 |
Z-Wave Version | 6.61.00 |
Certification ID | ZC10-17065651 |
Z-Wave Product Id | 0x023D.0x0043.0x0001 |
Firmware Updatable | Updatable by Manufacturer |
Neutral Wire Required | ok |
Color | White |
Outdoor Use | ok |
Sensors | Motion/No Motion (Binary) |
Communications Connections | None |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |
Supported Command Classes
- Alarm
- Association Grp Info
- Association V2
- Basic
- Battery
- Device Reset Locally
- Firmware Update Md
- Manufacturer Specific
- Powerlevel
- Security
- Switch Binary
- Version V2
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
-
Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers. -
Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls. -
Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network. -
Inclusion — is the process of adding new Z-Wave devices into a network.
-
Exclusion — is the process of removing Z-Wave devices from the network.
-
Association — is a control relationship between a controlling device and
a controlled device. -
Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate. -
Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>