Qubino Flush Dimmer 0-10V GOAEZMNHVD1 Manual

: June 8, 2024
: QUBINO

Table of Contents

Qubino
Flush Dimmer 0-10V

Qubino

Flush Dimmer 0-10V

SKU: GOAEZMNHVD1

Quickstart

This is a
secure
10V Dimmer
for
Europe.

To run this device please connect it to your mains power supply.

To add this device to your network execute the following action:

press service button S for more than 2 second or
press push button I1 three times within 3s (3 times change switch state within 3 seconds).

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Universal dimmer module with a standard 0-10V output and a multi-function input, which may be a push button / switch, a potentiometer or 0-10V signal.

Push button (mono stable switch)
Bi stable switch”
Potentiometer
0-10V input (requires external source)”

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

press service button S” for more than 6 second or”
press push button I1″ five” ” times within 3s ( 5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Installation

“

Before the installation disconnect power supply (1224VDC)
Connect the module according to electrical diagram.”
Locate the antenna far from metal elements (as far as possible).”
Do not shorten the antenna.

Note!” Do not connect the module to loads exceeding recommended values. Connect the module only in accordance to the below diagrams. Improper connections may be dangerous.

NOTE: ” When connecting temperature sensor to module that has already been included, you have to exclude module” first. Switch off power supply, connect the sensor and re-include the module.”

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

press service button S for more than 2 second or
press push button I1 three times within 3s (3 times change switch state within 3 seconds).

Exclusion

press service button S for more than 6 second or”
press push button I1 five” times within 3s ( 5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply.

Auto-Inclusion

Beside the standard inclusion this devices supports the so called auto inclusion.
Right after powering up the device remains in inclusion state and can be included by
(any) gateway without further actions on the device itself. The auto inclusion mode will
time out after some time.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

Make sure a device is in factory reset state before including. In doubt exclude before include.
If inclusion still fails, check if both devices use the same frequency.
Remove all dead devices from associations. Otherwise you will see severe delays.
Never use sleeping battery devices without a central controller.
Dont poll FLIRS devices.
Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

1	1	Lifeline
2	16	basic on/off
3	16	start level change/stop level change
4	16	multilevel set”
5	16	multilevel sensor report (triggered at change of analogue sensor)
6	16	multilevel sensor report (triggered at change of temperature sensor)”

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200âit may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: Input switch type

__
Size: 1 Byte, Default Value: 0

SettingDescription

0	mono-stable switch type (push button)
1	bi-stable switch type

Parameter 5: Working mode

With this parameter is possible to change the module presentation on the user interface.

NOTE : After parameter change, first exclude module (without setting parameters to default value) then wait at least 30s and then re include the module!
Size: 1 Byte, Default Value: 0

SettingDescription

0	Dimmer mode
1	Switch mode

Parameter 10: Activate / deactivate functions ALL ON / ALL OFF

__
Size: 2 Byte, Default Value: 255

SettingDescription

255	ALL ON active, ALL OFF active.
0	ALL ON is not active, ALL OFF is not active
1	ALL ON is not active, ALL OFF active
2	ALL ON active, ALL OFF is not active DIN Dimmer module responds to commands

ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.

Parameter 11: Automatic turning off output after set time

__
Size: 2 Byte, Default Value: 0

SettingDescription

0	Auto OFF disabled
1 – 32536	1 second – 32536 seconds Auto OFF enabled with define time, step is

1 second.

Parameter 12: Automatic turning on output after set time

__
Size: 2 Byte, Default Value: 0

SettingDescription

0	Auto ON disabled
1 – 32535	1 second – 32535 seconds Auto ON enabled with define time, step is

1 second

Parameter 21: Enable/Disable Double click function

If Double click function is enabled, a fast double click on the push button will set dimming power at maximum dimming value.
Size: 1 Byte, Default Value: 0

SettingDescription

0	double click disabled
1	double click enabled

Parameter 30: Saving the state of the device after a power failure

__
Size: 1 Byte, Default Value: 0

SettingDescription

0| DIN Dimmer module saves its state before power failure (it returns to the last position saved before a power failure).
---|---
1| DIN Dimmer module does not save the state after a power failure, it returns to off position.

Parameter 40: Power reporting in Watts on power change

Set value means percentage, set value from 0 – 100=0% – 100%.

NOTE: ” if power changed is less than 1W, the report is not send (pushed), independent of percentage set.
Size: 1 Byte, Default Value: 5

SettingDescription

0	reporting disabled
1 – 100	1% – 100% Reporting enabled. Power report is send (push) only when

actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%.

Parameter 42: Power reporting in Watts by time interval

Set value means time interval (0 â 32767) in seconds, when power report is send.
Size: 2 Byte, Default Value: 0

SettingDescription

0	reporting disabled
1 – 32767	1 second – 32767 seconds. Reporting enabled. Power report is send

with time interval set by entered value. Please note, that too fast reporting can cause too much Z-Wave traffic resulting in Z-Wave poor response

Parameter 60: Minimum dimming value

NOTE: ” The minimum level may not be higher than the maximum level! 1% min. dimming value is defined by Z-Wave multilevel device class
Size: 1 Byte, Default Value: 1

SettingDescription

1 – 98	1% – 98%, step is 1%. Minimum dimming values is set by entered value.

Parameter 61: Maximum dimming value

NOTE : The maximum level may not be lower than the minimum level! 99% max. dimming value is defined by Z-Wave multilevel device class.
Size: 1 Byte, Default Value: 99

SettingDescription

2 – 99	2% – 99%, step is 1%. Maximum dimming values is set by entered value.

Parameter 65: Dimming time (soft on/off)

Set value means time of moving the DIN Dimmer between min. and max. dimming values by short” press of push button I or controlled through UI (BasicSet).
Size: 2 Byte, Default Value: 100

SettingDescription

50 – 255	500 mseconds – 2550 mseconds (2,55s), step is 10 mseconds

Parameter 66: Dimming time when key pressed

Time of moving the DIN Dimmer between min. and max dimming values by continues hold of push button I or associated device.
Size: 2 Byte, Default Value: 3

SettingDescription

1 – 255	1 second – 255 seconds

Parameter 67: Ignore start level

This parameter is used with association group 3. A receiving device SHOULD respect the start level if the Ignore Start Level bit is 0. A receiving device MUST ignore the start level if the Ignore Start Level bit is 1.

Size: 1 Byte, Default Value: 0

SettingDescription

0	respect start level
1	ignore start level

Parameter 68: Dimming duration

This parameter is used with association group 3. The Duration field MUST specify the time that the transition should take from the current value to the new target value. A supporting device SHOULD respect the specified Duration value.”

Size: 1 Byte, Default Value: 0

SettingDescription

0	dimming duration according to parameter 66
1 – 127	from 1 to 127 seconds

Parameter 110: Temperature sensor offset settings

Set value is added or subtracted to actual measured value by sensor.
Size: 2 Byte, Default Value: 32536

SettingDescription

1 – 100| value from 0.1 “°C to 10.0 “°C is added to actual measured temperature.
---|---
1001 – 1100| value from -0.1 “°C to -10.0 “°C is subtracted to actual measured temperature.

Parameter 120: Digital temperature sensor reporting

If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter.”
Size: 1 Byte, Default Value: 5

SettingDescription

0	reporting disabled
1 – 127	0,1″°C – 12,7″°C, step is 0,1″°C

Parameter 250: Unsecure/Secure Inclusion (Version 2.04 or higher)

__
Size: 1 Byte, Default Value: 0

SettingDescription

0	Unsecure
1	Secure

Technical Data

Dimensions	41,8×36,8×15,4 mm
Weight	28 gr
Hardware Platform	ZM5202
EAN	3830062070553
IP Class	IP IP20
Voltage	12-24V DC
Device Type	10V Dimmer
Generic Device Class	Multilevel Switch
Firmware Version	02.04
Z-Wave Version	04.22
Certification ID	ZC10-17025424
Z-Wave Product Id	0x0159.0x0001.0x0053
Frequency	Europe – 868,4 Mhz
Maximum transmission power	5 mW

Supported Command Classes

Basic
Device Reset Locally
Zwaveplus Info
Manufacturer Specific
Powerlevel
Version
Security
Switch Binary
Switch Multilevel
Switch All
Association Grp Info
Configuration
Association
Multi Channel Association

Explanation of Z-Wave specific terms

Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and
a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.