EQi Industrial S11 Folding Treadmill User Manual
- June 8, 2024
- EQi Industrial
Table of Contents
EQi Industrial S11 Folding Treadmill
Common Failures and Troubleshooting
Please call our dealer or our after-sales service team if you have any other questions.
Error messages on electronic meter and elimination methods.
Product Maintenance
Lubrication
When the running belt is used for a period of time, it must be lubricated with
special methy silicone oil.
Advice
- 1 hour or less per week lubricate once every 6 months
- Less than 3 hours per week lubricate once every 3 months
- 3-6 hours per week lubricate once every 2 months
- More than 6 hours per week lubricate once a month
Do not lubricate too much. It is not the more lubricants, the better.
- Remember: Proper lubrication is an important factor in improving the life of the treadmill.
The method to check if you need to add lubricant.
Grab the running belt and touch the middle of the running belt back
with your hands as much as possible.You don’t need to add lubricant if you
have silicone on your hand (a little damp). You have to add lubricant if the
pad is dry and there is no silicone on your hand.
- The step of lubricating on the running plate (as shown in the right picture).
- Stop running and fold the machine.
- Lift the running belt of the underside of the main body, and put the oil pot as far as possible into the middle of the running belt. And spray methyl silicone oil inside the running belt and all the contacting area.
- You can keep the treadmill running in speed of 1 km/h to evenly lubricate then step on the running belt from left to right. After a few minutes, the methyl silicone oil can be completely absorbed by the running belt.
Adjust tightness of running belt. All treadmills shall be adjusted for
tightness before delivery and after installation.
However, the running belt may be loosened after a period of use.
For example, the treadmill would have stopping and slipping problem during
exercise. Adjust bolts of running belt with the left and right synchronous as
per clockwise direction to half a circle as the unit when this phenomenon
occurs.The user might slip if the running belt is too loose.
But it is not good to be too tight. It is easy to increase the load of the
motor therefore damage the motor, running belt and roller, etc.
Running Belt Deviation Adjustment
All treadmills need to be adjusted with the running belt before delivery and
after installation.But the running belt may be deviated after a period of use
which may be caused by the following reasons.
Please adjust the left bolt clockwise or right bolt counterclockwise if the running belt is left deviation.
Please adjust the right bolt clockwise or left bolt counterclockwise if the
running belt is right deviation.
Note: The running belt deviation is not within the scope of the warranty.
And it is mainly maintained by the user according to the manual. Running belt
deviation will seriously damage the running belt. The mistake must be detected
in time and corrected.
Service Commitment
T4014 electric treadmill, within one year of normal use, such as non-human damage, canprovide users with free accessories, after the expiration of the warranty period, the price ofspare parts to preferential prices.This product is for domestic use only and we are not responsible for any problems arisingfrom commercial use. If your product has after-sales problems, please call the local dealersafter-sales service!This manual is for reference only, please in kind prevail
This manual is for reference only, please refer to the actual product!
FCC
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>