WINSTARS TECHNOLOGY WS-WN552X1 AX1800 Dual Band Mesh WiFi Router Kit User Guide
- June 8, 2024
- WINSTARS TECHNOLOGY
Table of Contents
QUICK START GUIDE
AX1800 Dual-Band Mesh
WiFi Router Kit
WS-WN552X1
Overview
- LED Indicator
- DC Jack
- On/Off Switch
- Reset Button
- Pair Button
- Gigabit Ethernet Ports
- USB Port
- Touchlink Pad
Pair Button:
Press and hold for rnore than 2 seconds to add an extra rnesh device to the
existing Wi-Fi system.
Reset Button:
Press and hold for seconds to reset the mesh device.
LED Indication
Router Mode | LED | Description |
---|---|---|
Solid purple | The device is being activated. | |
Solid blue | The Internet is connected. | |
Blue flash | 1.Touchlink is in progress. |
2.Router mode device is being paired with other mesh devices.
Slow red flash| No access to the Internet.
Fast red flash| The device is disconnected.
| LED| Description
---|---|---
Extender Mode| Solid purple| The device is being activated.
Solid blue| The connection between mesh devices is excellent.
Blue flash| 1.Touchlink is in progress.
2.Mesh device is being paired with router mode device.
Slow red flash| No access to the Internet.
Fa, red flash| The device is disconnected.
Basic Info
Default IP: 192.168.10.1
Default Password: admin
Login : http://ap.setup
Mesh SSID: MeshGo_XXXX
Touchlink SSID : MeshGo_Touch
Router Configuration
-
Select one of mesh devices as your router, connect its WAN Port to the modem or LAN port of router then plug it in a power outlet.
-
Connection
2.7 Via Wireless
Turn on your Wi-Fi, search SSID “MeshGo_XXXX” and connect to it; then you can start configuring. 2.2 Via Cable Connect Ethernet cable to your PC/laptop and device LAN port. then you can start configuring. -
Launch a browser from your laptop/PC or smart phone and enter or in the address field. The default password is admin.
-
Select your Country/Region and Time Zone; for your network security, we suggest that you create a new login password. Note: The three colored bars in “Password strength” area indicates the strength of the login password.
-
Then you can change your SSID or use the default one. As for Encryption Mode, if your device supports WPA3/WPA2-MIX, we suggest you choose “WPA3/WPA2-MIX” . For network security, please create a Password according to the rules.
-
The system will then guide you to the Network page for the Mode selection and WAN Type, after selecting, please click save. Which WAN (Ethernet) Mode should I choose?
If the ISP provide you a account and password,please choose PPPoE; If the ISP not provide any parameters, the computer directly connect the internet cable, then can surf the internet, please choose DHCP; If the ISP provides you a fixed IP and other information, please choose Static IP. -
Please wait patiently for the process to complete, then you can enjoy your wireless network.
LAN Backhaul
- If your wireless signal weakens because of complex environment, you can try the second option LAN Backhaul.
- Repeat steps in the “Wireless Backhaul” section, then connect the “LAN/Backhaul” port of the extender to “LAN” port of your router
T ouchlink Technology
At the top of the mesh device there is the Touchlink sensing pad; once you touch the pad with your hand or other devices, the sensing pad will blink blue, indicating that Touchlink is in process, then you can search “MeshGo_Touch” and connect to it without any password.
Note:
Touchlink works for smart phone, tablet computer, laptop. etc. If you want to
change the configuration of Touchlink, then you can do as follows:
- Log in to 192.168.10.1 or ap.setup.com,then choose “Advanced” and select “Guest Wi-Fr.
- The default Guest WI-Fl Mode is Touchlink.
- The length of Touchlink time (Duration) can be set to 30s. 720s andl 240s, the default is 720s.
- You can also set the length of time (Use Time) for your guests.
More Mesh Devices
Generally, a mesh router device supports up to 7 mesh devices. Therefore, if
you need to add more mesh devices to build up• a stronger network in your
home, you simply need to pair the new mesh devices with the existing network.
Option I
- Log in to ap.setup or 192.168.10.1.
- “Wl-F;” “Mesh ‘Network”.
- You can add extra devices by entering’ their “Pair Ke (Pair key is at the bottom, of the device).
Option II
After configuring the main router, please press and hold the pair button of mesh devices for 2 seconds. When LED lights become solid blue, the pairing process is successfully completed.
Firmware Upgrade
Firmware upgrade can fix bugs of the router. However, we DO NOT recommend you upgrade the firmware of the router if it works properlyIf you need to update firmware, please proceed as the following steps:
- Click “Advanced” and select “Firmware Update”.
- Click on to locate the extracted firmware file.
- Click on “Upload” and choose “Apply”, and wait for the firmware upgrade process to complete.
Warranty viods if you interrupted the upgrade procedure.
FAQ
Ql. Why doesn’t the login page appear after enteringhttp://ap.setup?****
– Make sure your PC is net to obtain IP address automatically
– Please make sure you entered the correct website.
– Reboot your device and try again.
Q2. What can I do if I can not access the Internet?****
– Make sure your Internet works normally. please contact your ISP(Internet
Service Provider) if it doesn’t.
– Initiate your browser. enter 192.168.10.1 or ap.setup, then set up the
following quick start guide.
– Reboot your device and try again.
Q3. What should I do if I can’t have access to 162.166.10.11 or ap.setup on my android phone?****
– We suggest you turn off your 4G signal first before you set up the network, then turn it on when the configuration is done.
Q4. What can I do if I forget my administration management password?****
– Please refer to Q3 to reset the device, the default password is admin.
Q5. How do I find the best location for mesh devices?****
– Please put your mesh devices in a relatively open space to avoid obstacles such as metal objects, reinforced concrete walls and so on.
Q6. Why the flow monitoring is inaccurate?****
– The Hardware NAT Settings’s default open status leads to the absence of monitored data. If you wanna, keep the flow monitoring accurate, you have to tum off the Hardware NAT Settings function manually. which inevitably will increase the CPU usage.
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as
household or general waste. It should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment, or
returned to the supplier for disposal
RF exposure statement
This equipment meets the exemption from the routine evaluation limits in
section 2.5 of RSS-102. It should be installed and operated with a minimum
distance of 20cm between the radiator and any part of your body. Cet
~quipement est conforme ~ l’exemption des limites d’~valuation habituelle de
la section 2.5 de la norme RSS-102. II doit
~tre install~ et utilis~ ~ une distance minimale de 20 cm entre le radiateur
et toute partie de votre corps.
IC WARNING
This device contains licence-exempt transmitter(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device is restricted to indoor use only when operating in the 5150 to 5250
MHz frequency range.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.