Axminster Tools Mafell A12 Drill Driver 12V Instruction Manual

Mafell A12 Drill Driver 12V
Instruction Manual

Mafell A12 Drill Driver 12V

WARNING
Please read all safety instructions and directions. Failure to comply with the safety instructions and directions can cause electric shock, fire and/or serious injuries. Please retain all safety instructions and directions for future reference.

EC Declaration of Conformity
We herewith confirm that the machine A12 complies with the EU directives quoted. The standards listed were used for design and construction Empowered person for the configuration of the technical documents: Mafell AG

2006/42/EG
2014/30/EU
2011/65/EU| EN 62841-1, EN 62841-2-1, EN 55014-1, EN 55014-2
EN 12100
---|---
A12| Art-Nr. 910001, 910021

Mafell AG
D-78727 Oberndorf, den 29.11.2021

Dipl.-Ing. Matthias Krauss
Vorstandsvorsitzender / CEO|
i. V. Dipl.-Ing. Harald Schmid, MBA
Leitung Entwicklung und Konstruktion
---|---

Signs and symbols

This symbol is found in all places where you will find information for your safety.
Non-compliance with these instructions may result in very serious injuries.
This symbol indicates a potentially hazardous situation.
If this situation is not avoided, the product or objects in its vicinity may get damaged.
This symbol indicates tips for the user and other useful information.

Product information

for machines with product no. 91D001, 91D021
2.1 Manufacturer´s data
MAFELL AG, Beffendorfer Straße 4, D-78727 Oberndorf / Neckar, Phone +49 (0)7423/812-0, Fax +49 (0)7423/812-218, e-mail: mafell@mafell.de
2.2 Machine identification
All details required for machine identification are available on the attached rating plate.
CE symbol to document compliance with the basic safety and health requirements according to Appendix I of the Machinery Directive.
For EU countries only
Do not dispose of electrical tools together with domestic waste! In accordance with the European directive 2002/96/EC on waste electrical and electronic equipment and transposition into national law, obsolete electrical tools must be collected separately and recycled in an environmentally-compatible manner.
Read the operating instructions. This reduces the risk of injury.
Protect the rechargeable battery from heat, excessive solar radiation, fire, frost, waterand humidity. Protect rechargeable battery packs from humidity!
Protect rechargeable battery packs from fire! There is danger of explosion!
Cordless Allicance System (=CAS) is a cross-manufacturer battery pack systemFurther information is available at www.cordless-alliance- system.com

2.3 Technical

2.4 Emissions
The values stated are emission levels. Although there is a correlation between emission and imission level, it cannot be reliably derived from this whether additional  recautions are necessary. Factors influencing the current immission level existing at the workplace comprise the duration of exposure, the room characteristic, other source of noise, etc. such as e.g. the number of machines and other adjacent machining operations. In addition, the permissible immission level may differ from country to country. This information is nevertheless suitable for providing the machine user with an improved assessment of the hazard and risk.
2.4.1 Noise emission specifications
Noise emission values determined according to EN 62841-1 and EN 62841-2-1:

| Sound pressure level (LpA)| Sound power level (LWA)
---|---|---
A12| 72 dB (A)| 83 dB (A)
Uncertainty (KWA)| 3 dB (A)| 3 dB (A)

2.4.2 Vibration value specification
The typical hand-arm vibration is less than 2.5 m/s2
The measuring inaccuracy is 1.5 m/s2
2.5 Scope of supply
Cordless drill driver A12 complete with:
1 cordless screwdriver
1 quick-release chuck
2 rechargeable batteries 12 M 43 (4.0 Ah)
1 charger
1 angle attachment
1 belt clip
1 operating manual
1 folder “Safety instructions”

2.6 Use according to intended purpose
The drill driver A12 M is suitable for drilling in metal, wood, plastic and similar materials as well as for screwing and tapping. Any other use than described above is not permissible.
The manufacturer cannot be held liable for any damage arising from such other use. In order to use the appliance as intended, you must comply with the operating, maintenance and repair instructions specified by MAFELL.
Corrective maintenance work must be carried out by MAFELL authorised dealers or MAFELL customer service stations. The safety instructions applicable in the respective country of use as well as other generally recognised rules pertaining to safety and occupational health must be observed.
Unauthorized changes to the appliance shall rule out any manufacturer liability for damages resulting thereof. Only use original Mafell / CAS rechargeable batteries and accessories.

Safety instruction

Danger
Electrical appliances may be dangerous if used incorrectly. Therefore, always observe the safety instructions summarised ithis chapter and the safety regulations applicable in the respective country of use!
3.1 Safety instructions for all types of work
– Wear ear protectors during the use of drill drivers. Exposure to noise can cause loss of hearing.
– Always hold the appliance by the insulated gripping surfaces when carrying out work during which the bit may hit concealed power lines. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

3.2 Safety instructions for the use of long drill bits
– Always start drilling at low speed and with the drill bit in contact with the workpiece.
– On no account may you work at a speed that exceeds the maximum speed permitted for the drill bit. At higher speeds, the drill bit can easily bend if allowed to turn freely (without contact with the workpiece); this can lead to injuries.
– Do not apply excessive pressure and only apply pressure in the longitudinal direction to the drill bit. Drill bits can bend and thus break or lead to a loss of control and injuries.

3.3 Additional safety instructions
– Ensure that the machine is switched off when you push in the rechargeable battery. – Remove the rechargeable batteries from the machine before carrying out any setting, retooling, maintenance or cleaning tasks.
– Dust originating from materials such as leaded paint, some types of wood, minerals and metal can be harmful to health. Touching or inhaling these dusts can cause allergic reactions and/or respiratory disorders in the user or persons staying in the vicinity.
– As far as possible, make use of a dust extraction system. – Provide for good ventilation of the workplace.
– It is recommended to wear a respirator mask with filter class P2.
– Observe the regulations valid in your country for the materials to be machined. – Secure the workpiece against shifting, e. g. by means of fastening devices.
– LED light (Fig. 1, 10): Do not directly look at the LED radiation with optical instruments.

Layout

4.1 Depicted components (see Fig. 1)

1. Exchangeable attachment (chuck)
2. Adjusting ring – torque preselection
3. Gear change slide – first or second gear
4. Sense of rotation selector switch, double side(5) Bit adapter
5. Belt clip, can be used on both sides
6. Button – capacity display
7. Rechargeable battery
8. Capacity and signal display
9. LED light
10. Switch trigger

4.2 Symbols

Operation

5.1 Rechargeable battery, capacity and signal display (see Fig. 1)

• Charge the rechargeable battery prior to use.
• Recharge the rechargeable battery in case of loss of power.
• Press the button (7) to query the charge condition of the rechargeable battery. The capacity can be read off the LED lights (9).
• If a LED light (9) flashes, the rechargeable battery is almost empty. Recharge the rechargeable battery.
• The optimum storage temperature is between 10 °C and 30 °C.

5.2 Removing and inserting the rechargeablebattery (see Fig. 2)
Removing: Press the unlocking mechanism (12) andpull the rechargeable battery (8) out to the front. Inserting: Push on the rechargeable battery until iclicks into place.
5.2 Removing and inserting the rechargeablebattery (see Fig. 2)
Removing: Press the unlocking mechanism (12) andpull the rechargeable battery (8) out to the front.
Inserting: Push on the rechargeable battery until iclicks into place.
5.4 Selecting the gear speed (see Fig. 1) |
Actuate the switch slider (3) only when the motor is standing still!
1 First gear: low speed, high torque; preferably for screwing
2 Second gear: high speed; preferably for drilling
5.5 Setting the torque (see Fig. 1)
Set the torque by turning the adjusting ring (2).
1…10 = Torque limiting (setting range 0.5 – 5Nm)
= Adjusting the drill setting (max. torque, without torque control). Do not block the spindle to avoid overloading the motor.
5.6 Switching on/off, setting the speed (see Fig. 1)
Switching on: Press the switch trigger (11) and keep it depressed. The speed at the switch trigger can be changed by the depth to which it is depressed.
Switching off: Release the switch trigger (11).
5. 7 Tool change
Only use high-grade tools, which are suitable for the forces and torques occurring! Broken tools wlead to a machine defect. If repairare necessary, contact the customer service stations for MAFELL electrical tools.
The spindle enables a quick change between the accessory attachments and a direct ¼‘‘ hexagonal adapter.
Demounting the attachment: (see Fig. 3) Pull the locking ring (13) forward and pull off the attachment to the front.
Mounting the attachment: Pull the locking ring (13) forward and push the attachment onto the spindle up to the limit stop. (If necessary, turn the attachment slightly to and fro.)
Turning the attachment: With the angle and eccentric attachment (optional accessories) you can adjust the angle of the attachment in 30° steps to the screwdriver axis.
Pull the locking ring (13) forward and push the attachment onto the spindle into the desired position until it clicks into place again.

5.7.1 Quick-release chuck (see Fig. 1)
Opening the chuck: Turn the chuck (1) in direction of rotation . Place the bit as deeply as possible into the open chuck. Turn the chuck (1) in direction of rotation until the tool is firmly mounted.
5.7.2 Angle attachment
The angle attachment can be used to work at right angles to the screwdriver axle. Mount the bits directly by means of the ¼‘‘ hexagon adapter or by attaching the chuck or bit holder.
5.7.3 Quick-release bit holder (optional accessories)
Inserting the bit: Push the bit into the bit holder until it audibly clicks into place.
Removing the bit: Pull the sleeve at the bit adapter forward until it clicks into place and remove the bit.

5.7.4 Eccentric attachment (optional accessories)
With the eccentric attachment it is possible to work close to the edge of inside corners.Inserting the tool: Pull the sleeve at the adapter  backwards and insert the tool up to  he stop into the ¼‘‘ hexagon adapter. Removing the tool: Pull the sleeve at the adapter backwards and remove the tool.

5.8 Switching the LED light on/off (see Fig. 1)

• Press the switch trigger (11) to switch on the LED light (10).
• After releasing the switch trigger (11), the LED mlight (10) still glows for approx. 5 sec. and then switches off.

5.9 Belt clip
For an easier handling of the belt clip, remove the rechargeable battery (see chapter 5.2)  (see Fig. 4)
Detaching:

• Press the belt clip (6) together at the rear.
• Swivel it out of the rear opening.
• Slacken the belt clip and remove it from the front opening.

Attaching:

• Press the belt clip (6) together and insert it into the openings provided.
• The belt clip (6) can be attached on both sides.

5.10 Bit adapter (see Fig. 1)
A screw bit can be fitted in the bit adapter (5) on both sides.

Service and maintenance

Danger
Unplug the rechargeable battery foall service work.
MAFELL machines are designed to be low in maintenance. Always keep the appliance clean. Should the appliance fail despite thorough manufacturing and testing procedures, the repair must be carried out by an authorised customer service station for MAFELL electrical tools. Store the appliance in a dry and frost-proof place. Only use MAFELL accessories and spare parts. Have components, the replacement of which has not been described, replaced at a MAFELL customer service station.

6.1 Storage
Clean the machine thoroughly if the machine is not used for a longer period of time. Spray blank metal parts with a rust-proofing agent.
6.2 Transport
The included Li-ion rechargeable batteries are subject to the requirements of dangerous goods legislation. The rechargeable batteries can be transported by the user on the road without any further requirements. For the dispatch by third parties (e.g.: air transport or forwarding agent), special requirements for packaging and labelling must be observed. In this case, a dangerous goods expert must be consulted when preparing the package. Only dispatch rechargeable batteries if their housing is undamaged. Tape open contacts and pack the rechargeable battery so that it does not move in the packaging.
Please also observe any further national regulations.

6.3 Disposal of rechargeable batteries/batteries
Electrical tools, rechargeable batteries, accessories and packaging should be recycled in an environmentally friendly manner.
Do not dispose of electrical tools together with domestic waste!
For EU countries only:
According to the European Directive 2002/96/EC, power tools that are no longer serviceable, and according to the European Directive 2006/66/EC, defective or used rechargeable batteries/batteries must be collected separately and recycled in an environmentally sound manner.kklj
Return unusable rechargeable batteries/batteries
directly to: Germany
Stiftung
GRS Batterien
Heidenkampsweg 44
20097 Hamburg
Germany
Rechargeable batteries/batteries:
Li-Ion:
Please comply with the information in Section “Transport”, page 21.

Troubleshooting

Danger
Determining the causes for existing defects and eliminating these always requires increased attention and caution.
If the machine switches off automatically, the electronic system has activated self-protection mode. Despite this protective function, overload and as a consequence damage to the machine may occur during certain applications.
Some of the most frequent defects and their causes are listed in the following chart. In case of other defects, please contact your dealer or the MAFELL customer service directly.

Rechargeable battery is almost empty.
The electronic system protects the rechargeable battery from deep discharge.| Charge the rechargeable battery.
The machine switches off and cannot be switched on again. A warning signal sounds and the LED light (10) flashes.| Overload
A sustained load has overheated the machine or the rechargeable battery.| Signal goes out after releasing the switch trigger (11). Allow the machine and the rechargeable  battery to cool down.
Note: The machine cools down faster when it is allowed to idle after it is switched on again.
Machine switches off. A warning signal sounds and the LED light (1 0) flashes. Machine restarts when it is switched on again.| Excessive current rating.
This leads to the machine being switched off, e.g. in the event of prolonged blockage.| Switch off the machine by releasing the switch trigger (11).
Afterwards, you can switch the machine back on again and resume work. Try to avoid further blockages.

Optional accessories

– Rechargeable battery 12 M 43 LiHD
– APS M charger – GB
– APS M charger
– APS M + quick-charger
– APS M + quick-charger – GB
– Angle attachment A-SWV 10
– Chuck A-SBF 10
– Quick bit holder A-SBH
– Eccentric attachment A-SEV| Order No. 094508
Order No. 094493
Order No. 094492
Order No. 094509
Order No. 094511
Order No. 206773
Order No. 209338
Order No. 206766
Order No. 209339
---|---

Exploded drawing and spare parts list
The corresponding information in respect of spare parts can be found on our homepage: www.mafell.com

WARRANTY

Upon presentation of the warranty document (original invoice), we will carry out all repairs free of charge in accordance with the applicable warranty provisions, processing and mounting faults free of charge on presentation of this properly filled-in Guarantee Certificate and your original receipt. This is not valid for consumables and wearing parts. For this purpose, the machine or the appliance is to be forwarded freight paid to our plant or to an authorized MAFELL repair service. Refrain from trying to carry out the repairs yourself as otherwise your warranty claim will become extinct. We do not accept any liability for any damage resulting from improper handling or normal wear.

MAFELL AG
Beffendorfer Straße 4, D-78727 Oberndorf/Neckar
Internet: www.mafell.de
E-Mail: mafell@mafell.d

References

• System
• CAS - The Cordless alliance for your brands

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>