iFI Go Blu Portable Headphone Instruction Manual

iFI Go Blu Portable Headphone

Power on/off, Bluetooth format annunciation, Voice alert on/off and

digital filter mode on/off

Power switch

Long press and hold the power switch for > 3s to power on/off the GO blu.

Bluetooth format annunciation

Press the power switch twice and the voice will announce the
Bluetooth format you are currently receiving.

Voice annunciation on/off

In the shutdown state, first press the Bluetooth pairing key (3) without releasing it, and then press the power key to turn it on.
The operation method of turning off and turning on voice annunciation is the same.

Digital filters

To enter/exit filter selection mode, short-press button (1) three times, a beep will sound, then press button (3) to select filter. See item (4) for digital filter mode LED colours.
“STD” Standard, modest filtering, modest pre and post ringing “MIN” Minimum phase, slow roll-off, minimum pre and post ringing

Multi-function knob

Controls:

• Volume control (turn)
• Play/ Pause (a short click)
• Skip forward (two short clicks)
• Skip back (three short clicks)
• Wake up voice assistant (long press

Answer the phone:

• Answer the call (short press)
• Hang up (long press)

Settings, Bluetooth pairing, Voice alert on/off, Digital filter mode and

restore factory setting

This button cycles between (Please refer to item 4):
Off> XBass > XS pace> XBass + XS pace (short press) Pairing (long press> 3s, indicator flashes red/blue)
Restore factory settings (press and hold for> 1 Ss, indicator flashes white 3 times)

Sound effects and Bluetooth status LED

The LED colour scheme indicates the current sound effects and Bluetooth status of GO blu.

Bluetooth

Pairing

From switch on, the GO blu will blink blue as it searches for a previously paired device If a stored device is not found, it will automatically enter pairing mode and blink blue/red
To enter pairing mode, long-press button (3) until Bluetooth Mode LED flashes blue I red. To pair, look for ‘GO blu’ in the list of available Bluetooth devices on your phone.
The GO blu is able to store up to 8 paired Bluetooth devices.

Digital filter

Note: Short press the power button 3 times to enter the digital filter mode adjustment, then short press the filter mode selection button (3) to change the digital filter type. Short press the power button 3 times again to keep the current selection and exit the digital filter selection mode (it will beep). It will also exit the filter mode and retain the filter selected if no button is pressed for 30 seconds.

Restore factory settings

Note: You need to use the factory reset in the power-on state, during which no other operations can be performed; when the factory reset is successful the white light will flash 3 times with a beep sound. After the operation is successful the device will be in the power on state.

Warning: Restoring the factory settings will clear all the memorized 8/uetooth addresses, XBass and XSpace will be turned off, and voice (decoding format) announcement will be turned on.

Balanced 4.4mm headphone output

Connect balanced 4.4mm headphones.

S-Balanced 3.5mm headphone output

Connect 3.5mm headphones.

Factory Reset

System reset (long press >3s).

USB-C input

The USB-C socket isn’t just a charging port, it plays up to 24 bit 96kHz directly from USB input. It will take <40 minutes for a highpowered USB charger to fully charge GO blu. Use the enclosed USB ‘Type A’ to ‘Type C’ cable, smart charger or a regular charger up to 6.3V.

Note: To switch the audio source from B luetooth to USB, please stop music playback and disconnect the GO blu from the Bluetooth source. Connect the USB-C input (8) to the U SB audio source via a U SB cable and select the GO blu as the playback device.

To switch from USB to Bluetooth transmission, disconnect the GO blu from the audio device and reconnect the Bluetooth device.

The default setting of the phone does not allow charging of the GO blu (except in exclusive mode).

Tip: Exclusive mode is when the device outputs only the sound of the currently used application. Only a few applications have an exclusive mode setting; in general there is no difference to charging the GO blu between turning exclusive mode on or off. However some applications allow charging with exclusive mode on.

LED for Battery Status

*Battery LED will flash when it is charging and will go out when it is fully charged.

Microphone

Built-in mic for hands-free calls when paired with your smartphone.

Tip: To wake up your phone’s voice assistant, long-press the multi- function knob.
Note: Current instructions apply to firmware version 3.05 and higher.
Tip: For the required driver and all the latest firmware updates please visit our website: www.ifi-audio.com/download-hub/

Specifications

Bluetooth 5. 1 ™ ( AAC, SBC, aptX, aptX HD, aptX Adaptive, aptX LL, LDAC, LHDC/HWA Codec)
Power System| Charging via USB-C, BC V1 .2 compliant up to 1 000mA charging current and 6.3 volts
Headphone Outputs:
Balanced:| 4.4mm
Un BAL:| 3.5mm
Power Output:
Balanced:| 245mW@32Ω; 5.6V@600OΩ
Un BAL:| 165mW@32Ω; 2.8V@600Ω
Output Impedance:
Balanced:| <1Ω
Un BAL:| <1Ω
SNR:
Balanced:| 111 dBA
Un BAL:| 106.5dBA
DNR:| 120dB(A) (BAL/Un BAL)
THD+N:
Balanced:| <0.009% (6.5mW/2.0V @600Ω)
Un BAL:| <0.03% (1 00mW/1.27V@ 16Ω)
Frequency Response:| 20Hz – 45kHz (-3dB)
Battery:| Lithium-polymer 450mAh approx. ~1Ω hours
Dimensions:| 54x34x 13 mm
2.1″ X 1.3″ X 0.5″
Net weight:| 27 g (0.95 oz)
Warranty period:| 12 months

*Specifications are subject to change without notice.

**GO blu**

**Tech Lowdown**

Hi-Res Portable Bluetooth DAC

The pocket-sized GO blu delivers heavenly headphone sound on the go.

• The world’s first miniature Bluetooth DAC/amp to support the latest hi-res codecs and deliver the bestquality audio streaming from smartphones, tablets and other portable sources.

• First miniature Bluetooth DAC to use the latest QC5100 chipset. This means Bluetooth v5.1 and twice as much processing power as the previous version still widely used today.
  

• Separate Bluetooth, DAC and amp stages – individually optimized for maximum performance

• Built-in mic for hands-free calls when paired with your smartphone

• Balanced twin-mono circuit design with Direct Drive equals ultra-low distortion

• Fully-balanced and S-Balanced outputs make the most of all headphone types
  

Superior Design And Components

Hi-Res Bluetooth

• Advanced Bluetooth module with QC5100 chipset handles every HD format
• All the latest 24-bit-capable Bluetooth audio formats are supported – AAC, SBC, aptX, aptX HD, aptX Adaptive, aptX LL, LDAC, LHDC/HWA
• Bluetooth implementation avoids typical 40% quality drop found with standard Bluetooth
• Future codecs can be added

Unique Sonic Tailoring

Tailor sound to suit your headphones and personal sonic taste.

|
---|---
Analogue bass boost.
Enhances low frequencies without muddying the mid-range.| Analogue headphone spatialiser.
Opens up your music to give you the spaciousness of a live concert.

Bluetooth-Status LEDs

Sound Effect-LEDs

Headphone Friendly

• Precision rotary volume control with auto-gain: Adjusts output to match your headphones
• Output delivers up to 5.6V for high power to drive even tough headphone loads with ease
• Two headphone outputs: 4.4mm Pentaconn balanced and 3.5mm S-Balanced
• S-Balanced output: Cuts distortion by 50% with single-ended headphone connections

Connection Guide

Specifications

LDAC, LHDC/HWA Codec)
Outputs| 4.4mm/3.5mm (BAL/UnBAL) USB-C — 24 bit / 96kHz

Power Output

| Balanced| 245mW @ 32Ω; 5.6V @ 600Ω
UnBAL| 165mW @ 32Ω; 2.8V @ 600Ω
Output Impedance| <1Ω (BAL/UnBAL)
SNR| 111dBA/106.5dBA (BAL/UnBAL)
DNR| 120dB(A) (BAL/UnBAL)
Chipset| Qualcomm QCC5100 Series
---|---
Input| USB-C/Bluetooth 5.0 ( AAC, SBC, aptX, aptX HD, aptX Adaptive, aptX LL, LDAC, LHDC/HWA Codec)
Outputs| 4.4mm/3.5mm (BAL/UnBAL) USB-C — 24 bit / 96kHz

Power Output

| Balanced| 245mW @ 32Ω; 5.6V @ 600Ω
UnBAL| 165mW @ 32Ω; 2.8V @ 600Ω
Output Impedance| <1Ω (BAL/UnBAL)
SNR| 111dBA/106.5dBA (BAL/UnBAL)
DNR| 120dB(A) (BAL/UnBAL)

Type A Connect

( where applicable)

This iFi device with a USB type A male was port as designed for direct connection to mobile devices to extract the digital signal.

Phone Connections

For connection via
Apple (iOS) use Apple USB-to-USB-C/Lightning:

Android* use On-The-Go (USB-C/USB-micro):

For further support FAQs and Support Ticket System: https://support.ifi- audio.com/. *Please ensure your Android is USB host mode compatible.

Note for Charging

( where applicable)

1. If the LED is BLUE when you first switch ON the machine, it means that it is sufficiently charged. If the LED is RED, please turn OFF the machine and charge until no LED is lit.
2. If you cannot power ON or if there is no LED light, please insert a USBcable with USB power 3-5 times, then the LED should be BLUE. It should stay like this for a few hours (depending upon how flat the battery is). If not, please re-insert the USB cable (with USB power) 3-5 times again, and once the LED is BLUE, leave for at least 6 hours.
3. After a long period on inactivity (say 3 6 months), please fully charge the machine again. Ideally, repeat this process once every 3 months.
4. If you encounter any issues, please contact our technical support department at: http://support.ifi-audio.com/

Dual Lock Fasteners

( where applicable)

WARRANTY

In order to activate the warra;nty for this iFi product, you must register with the iFi website.
Co!mponent:
Serial no:

Terms and Conditions

• iFi guarantees that this iFi product shall be free fron1 defects in materials and workmanship for a period of 1 year (electronic tube warranty for 6 months} for parts and labour.
  The warranty period begins at the date of retail sale by an authorized lFi distributor/dealer and is subject to the following requirements and understandings:

• It Is the responsibility of the buyer within 30 days from the original sale, to register and activate the product warranty with the iFi website.

• The original invoice must be produced for authentication prior to any warranty claim.

• The ifi product must not have been modified in any manner whatsoever, or the warranty will immediately beco1ne void.

• The lfi warranty is only valid in the country of original sale and is not transferable.

• The product must not have been stored in a humid environment; nor subjected to weather, water, or saltwater spray.

• iFi shall not, under any circumstances, be liable for any incidental or consequential damages arising from the loss of property or other dj:lmage or losses due to the failure of an ,Fi product. iFi is not liable for loss of use or inconvenience caused by the failu re of an iFi product. iFi is not liable for damage caused to other audio components because of the failure of an iFI product. ,

• During the warranty period, iFi will repair the product to working order, or, at iFi’s discretion, replace the defective module with a similar available product.

• All repairs performed after expiry of the warranty period will be charged to the owner and will carry a 180-day warranty on parts and labour. The customer is responsible for shipping thP unit to the iFi distributor in the original packaging. This includes the payment of any shipping charges and related taxes.

• Should any warranty issues arise, IF1’s decision is full a

After-Sales

3 Easy Steps …

Dear iFi customer: Thank you for purchasing this iFi product.

Please do not hesitate to contact us if you have any questions surrounding our products/support. http://support.ifi-audio.com/

MQA Setu p

( where applicable)

For MQA computer setup, please scan this QR code or type ‘ifi audio’ into **YouTube** search.

You will find two setup videos:

• MQA Decoder – eg Pro iDSD
• MQA Renderer- eg nano iDSD Bl

Just select the correct video setup for your device.

Any queries, please search the FAQs or open a support ticket here: (https://support.ifi-audio.com/)

References

• iFi audio | the Award-Winning Audio Technology Company
• Support Desk | iFi audio

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>