SWAGTEK TW5 True Wireless Earbuds Instruction Manual

: June 9, 2024
: swagtek

Table of Contents

Product summary
Cosmetic Drawing
- cosmetic
- Product list diagram
Material list of charging compartment

SWAGTEK TW5 True Wireless Earbuds

Product summary

Model name: TW5

weight and dimension : earphone dimension（dimension：241413mm charging case

SWAGTEK TW5 True Wireless Earbuds Product summary

 **Manual measurement, there is an error.**

gross weight : earphone （single 3.1±1 g）+charging case:43.5±1 g + giftbox g=g
net weight：earphone（single3.1±1 g）+charging case43.5±1 g=50g±1 g

Cosmetic Drawing

cosmetic

Product list diagram

Headphone material list:

serial number| product name| Specification| encapsulation| Dosage| Component position
---|---|---|---|---|---
1| Earphone PCB| 11.6mm18.1mm0.8mm*| PCB| 2|
2| CHIPSET| AB5617H2| SOP-16L| 2| U1
3| Transient suppression tube| WEP060RF0402 Continuous voltage 6.5V, breakdown voltage 8.3V| 0402| 0| C8
4|

SMD crystal oscillator

|

2520 26M passive crystal oscillator 9PF 10PPM

| 2520| 2| Y1
5|

Chip capacitors

| C.cap 105 10V X7R ±10%| 0402| 2| C4
6|

Chip Resistor

| | 0402| 2|

L1 (to be confirmed)

7| Chip Resistor| | 0402| 2|

L2 (to be confirmed)

8| Chip Resistor| | 0402| 2|

L3 (to be confirmed)

9|

SMD LED

| | 0603| 2| R
10|

SMD LED

|

red light

| 0603| 2| B
11|

SMD Condenser Microphone

| | | 2| MIC
12| button| | 1PIN| 2| CN1
13|

Charging copper column

| Ф1.5mm*7.5mm(JRMDB0120106A)| 1PIN| 2|
|

trumpet

|

Ф8* ?mm 32 ohms

| 2PIN| 2|
15|

rechargeable lithium battery

|

Rechargeable lithium battery 3.7V 25mA

| 2PIN| 2|
16|

SMD cost

| | | 1|
17|

SMD stencil

|

Each of L/R

| | 2|
18|

Test Fixture

|

L/R each one

| | 2|
19|

plastic

| | 0.011kg| 1|
20|

hardware

| | | 2|
21|

Silicone earmuffs

| | | 2|
22|

Silicone mat

| | | 2|
23|

Silicone mat

| | | 0|
24|

Dust net

| | | 2|
25|

Dust net

| | | 2|
26|

magnet

| | | 2|
27|

magnet

| | | 1|

Material list of charging compartment

serial number

|

product name

|

Specification

|

encapsulation

|

Dosage

|

Component position

---|---|---|---|---|---
1| Charging box motherboard PCB| 36.1mm31.9mm1.0mm|

PCB

|

1

|
2|

Master IC

| IP5513_LR188_NTC_GWS_UCCPI|

SOP-16A

|

1

|

U1

3|

Chip capacitors

| C.cap 225 16V X7R +80/-20%| 0603| 1| C3
4|

Chip capacitors

| C.cap 475 16V X7R +80/-20%| 0603| 3| C1 C2 C4
5|

Chip Resistor

| 100Ω ±5%| 0603| 0| R3 R4 R5 R6 R10
6|

Chip Resistor

| 33KΩ ±5%| 0402| 2| R1 R2
7|

Chip Resistor

| 51KΩ ±5%| 0402| 1| R1
8|

SMD inductor

| CD32-2.2uH (The quality of the inductance is stable)| CD32| 1| L1
9|

Digital Tube

| 2256 188 / YFTD2256SW-5| 5PIN| 1|
10| MICRO_USB|

micro5p 5.9 female seat with post, straight edge and flat mouth US01-664

| 6PIN| 1| CN2
11|

SMD charging copper column

|

Ф2.0mm*6.2mm board 5.5mm (JRMDB1121107A)

| 1PIN| 4| CN1
12|

rechargeable lithium battery

|

300mAH (601535) with protection board

| 2PIN| 1|
13|

SMD stencil

| | | 1|
14|

SMT chip fee

| | | 1|
15|

Test Fixture

| | | 1|
16|

magnet

| | | |
17|

magnet

| | | |
18|

sticker

| | | |
19|

Blister

| | | |
20|

Color box + PET

| | | |
21| manual| | | |
22|

PE bag

| | | |
23|

Double-sided EVA

| | | |
24| glue| | | |
25|

silk screen+spray

| | | |
26|

data line

| φ2.8mm2C20cm| | |

The circuit schematic diagram

earphone schematic

charging case schematic circuit

hardware parameter

Bluetooth chipset

serial number

|

name

|

Specification

---|---|---
1| Chipset name| AB5617H2
2| Bluetooth version| 5.0
3| Bluetooth protocol| Hfp，a2dp，hid，avcp，pmp
4| Working frequcncy| 2402~2480MHz
5| Effective range| 360°≥10,rice

Audio feature

speaker

104±3dB (1000KHZ 1MW) (INPUT VOLTAGE=126mV)

frequency range

| 10kHZ-20kHz
4| Microphone impedance| 200Ω

Earphone function diagram

function indication diagram

function list

earphone

NO.	Status	Actions
1	Power on	Earphone will power up by automatic fater open charging case
2	dual ear mode	earphone will power on by automatic after open the charging

case, R/L ，L/R earphone will finish pair by automatic, ， waiting serial second, TWS 。 after paired, the main earphone indicator will flash alternately, then open Bluetooth function in mobile menu to se rch, then click “TW5”
3| Single ear mode| take out any of L/R earphone and close he charging case,the earphone will power on automatic and automatic pair the another one earphone, after 30s,this earphone will get into single mode,res/blue led will flash alternately,open blue function in mobile

menu to search bluetooth, click TW5 to connect

charging case

1| Charging port| Power supply：DC4.5~6.0V,via Micro USB port to charge the charging case。
---|---|---
2| Indicator light| when charge the charging case, LED will flash in charging when charging case charge to earphone, red LED will light, after earphone battery being 100% charged, low battery power. If flashes per 5s
3| Headset Charging| place earphone into charging case, red indicate the earphone is charging
4| Length of charging cable| 20cm
NO.| Status| LED indicator
---|---|---
1| Power on| blue led fast flash 3 times
2| Pairing mode|

Red and blue lights flash alternately red/blue flash alternately

red led fast flash 3 times red led fast flash 3 times

8| Low battery| Battery power low, red led flash and there is warning tone
NO.| Status| Warning tone
---|---|---
1| Power on| Power On
2| Pairing mode| Pairing
3| Connection succeeded| Connected
4| Power off| Power off
5| Low battery| Low battery

others test

earphone capacity	30mah
Charging case	250mah
Charging case charge current	300mA
Charging case power off	35uA
Rated voltage	DC 3.0-4.2V
Charing time（0-100）	1-2hrs
Play time（single）50% volume	4H(from earphone power 100%)
play time(dual mode)	4H(from earphone power 100%)
Fully play time （dual mode）50% volume	12H(from charging case and earphone

both 100% power)
Standby time| ＞200hrs
working temperature| -10℃ — +45℃
Storage temperature| -20℃ — +60℃
Button control| 1 key : MUlti – function button

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.``