Jking RS1 Remote Controller User Manual

June 9, 2024
Jking

Jking RS1 Remote Controller

Jking RS1 Remote Controller

RS1 Remote Controller User Manual

Warm prompt : Thank you for purchasing this product! Incorrect operation may cause they cannot be used normally, even damage related equipment, we strongly recommend that you read this manual carefully before using the device, and strictly abide by the prescribed operating procedures. We assume no responsibility: for the use of this product, including but not limited to liability for incidental or indirect damage: meanwhile, we assume no responsibility for unauthorized modification of the product. We have the right to change the product design, appearance, performance and use requirements without notice.

Attention:
Short press the button means: Press the POWER button to release after 1 second:
Long press the button means: Press and hold the button without releasing

Specifications:

Name

| Specifications| Parameters
---|---|---
RS1 remote controller| Battery size|

502030

RS1 remote controller

| Capacitance| 3.7V/150mA
RS1 remote controller| Charging time|

Charge 50% in 20 minutes

RS1 remote controller

| Charging port| Type-c
RS1 remote controller| Lanyard|

Support

RS1 remote controller

| Weight| 56g
RS1 remote controller| Communication mode|

2.4G

RS1 remote controller

| Remote control distance|

Open field 14M

Function Description

Turn on the remote controller:

Short press the power button, indicator 1 will be constant on, indicator 2.3.4.5 flash for three seconds then all off.

Turn off the remote controller:

Long press the power button for three seconds, indicator 1 off, already turn off.

Remote controller turn off automatic:

Remote controller without connects the electric skateboard, will be turned off automatic after 30 seconds; When the remote controller connects the electric skateboard, will not turn off automatic, we must wait for the electric skateboard to turn off after it is disconnected for 30 seconds.

  1. Firstly turn on the power of the electric skateboard, long press the power button for five seconds, after the indicator flashes once every 0.5 seconds, the electric skateboard enters the pairing mode.
  2. Press and hold the power button of the remote control for 2 seconds to turn it on, and then short press the Power button and Reverse button together and release them. Do not hold them for a long time.
  3. When the indicator 1 of the remote controller flashes and the electric skateboard power indicator flashes, that means the remote controller and the electric skateboards are paired successfully.
    Notice: Long press the electric skateboard power button, short press the remote controller power button.
Electric skateboard power indicator:

It can be used when the remote controller connects to the electric skateboard successfully, indicator 3,4,5 and 6 shows the electric skateboard power,
Indicator 3,4,5,6 means 100%-75% power
Indicator 3,4,5 means 75%-50% power
Indicator 3,4 means 50%-25% power
Indicator 3 means 25%-5% power
When the indicator 3 flashes at a frequency of 0.5 seconds, means the power is less than 10%

Remote controller power indicator:

Within 5 seconds after the remote control is turned on, indicator 3,4,5,6 flashing to show the remote controller power,
indicator 3,4,5,6 flash for 5 times means“100%-75%”
indicator 3,4,5 flash for 5 times means“75%-50%”
indicator 3,4 flash for 5 times means “50%-25%”
indicator 3 flash for 5 times means“25%-5%”
When the indicator 2 flashes at a frequency of 0.5 seconds, means the power is less than 20%

Acceleration / brake:

Push the “roller” forward to control the skateboard forward,Pull the “roller” backwards to control the skateboard brake

Electric skateboard direction switch:

When the electric skateboard stopped, long press the Reverse button to switch the front and back direction of the electric skateboard, the electric skateboard driving forward, the indicator 1 shows green, short press the Reverse button again, the electric skateboard driving backward, the indicator 1 shows red, cycle back and forth.

Electric skateboard speed switch:

When the electric skateboard stopped, or when the electric skateboard was sliding, short press the
Reverse button to switch the four gears of the electric skateboard, first gear indicator 3 long bright, second gear indicator 4 long bright, third gear indicator 5 long bright, forth gear indicator 6 long bright, exit after 3 seconds if switch successfully,
Notice: When each gear and each indicator long bright, the other 3 indicators are off,
Mark: The first gear is low-speed gear, the second gear is medium-speed gear, the third gear is high-speed economic gear, the fourth gear is the violent gear of sports players

Switch the electric skateboard brake strength:

Pulling the “roller” backward and do not release, short press the Reverse button at the same time, Switch the electric skateboard brake strength to four gears,
The first gear indicator 3 flashes for 6 times,
The second gear indicator 4 flashes for 6 times,
The third gear indicator 5 flashes for 6 times,
The forth gear indicator 6 flashes for 6 times.
Notice: When each gear and each indicator flashes, the other indicators are off.

To turn on the LED light of electric skateboard.

When the remote controller is connected to the skateboard, double-click the Power button to turn on the skateboard LED lights (headlights)
Mark: Only the H2E,SUV model and the removable battery model have this function, not all the boards have this function.

To turn on the LEZD light of remote controller.

When the remote controller is connected to the skateboard, short press the the light on button of the remote controller to turn on the light. Short press it again to turn off the light.
The button to turn on the remote control light is on the top of the remote control (as described in the following figure)

Remote controller charging:

Remote controller charging Type-c, after the remote controller is connected and charged, remote
controller indicator 3,4,5,6 flashes quickly, (Similar trotting horse lamp) All four indicators are long bright, indicating that the remote controller is fully charged. the indicator 2 is always on red, the indicator 1 is always on green. Indicator 2 is the charging indicator lamp.

Remote controller battery protection:

The power of the remote controller is less than 20%, the indicator 2 flashes in red, when the power of the remote controller is less than 5%, the battery voltage is lower than 3.2v, pushing the “roller” forward is not allowed, pulling the “roller” backward to brake will be in normal.(Can’t move forward but can only brake).
When the power of remote controller is less than 1%, the voltage is 3.0V, the remote controller will automatically turn off.

Notice: When the power of the remote control is less than 20%, the indicator 2 flashes in
red, the rider should charge the remote controller in time, avoid lithium battery damage due to over discharge.

Loss of signal:

When the signal is lost, if the remote controller is accelerating, electric skateboard will stop
accelerating, the motor will slide freely. when the electric skateboard is in the state of braking, the signal loss time within 1 second, the brake is still valid. They will reconnect within 1 second, we can continue to use it normally, If the signal is lost for more than 1 second, the brake will be invalid, and the skateboard is equivalent to sliding freely

FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals