Dongguan Shangyuan Electronics H30 Noise Cancelling Headphones User Manual
- June 9, 2024
- Dongguan Shangyuan Electronics
Table of Contents
Dongguan Shangyuan Electronics
H30 Noise Cancelling Headphones
Model:H30
User Manual
The packing accessories
Product features
On/Off
- The boot:Press and hold the multifunction button for 2 seconds, and the LED indicator light will be blue and red after 1 second The lights blink alternately, and the headset enters the Bluetooth pairing mode.
- To turn it off:Press and hold the multifunction button for 4 seconds, the LED indicator light will blink red twice and then go off.
Bluetooth pairing
- When the headset is powered and turned off, press and hold the multifunction button for 2 seconds, and the LED indicator light will be blue After 1 second, the blue and red lights blink alternately, and the headset enters the Bluetooth pairing mode.
- Enable the Bluetooth function of the mobile phone. In the device list, select ‘H30° Bluetooth pairing, pairing successful can be used normally.
The noise reduction function
- After the headset is powered on, push the noise reduction switch/key, and the headset indicator light will turn on Noise reduction mode.
- After the headset is powered on, push the noise reduction switch/key, and the headphone indicator turns off Noise reduction mode.
Factory data reset
Press and hold the “+” and “2 keys for 5 seconds at the same time, the headset will disconnect the Bluetooth connection and restore factory outputSettings. You need to turn on your phone’s Bluetooth again, and then find and select in the device list “H30” performs Bluetooth pairing and can be used normally after successful pairing.
Audio features
- When Bluetooth is connected, insert the 3.5mm audio cable, and the Bluetooth is disconnected. The headset is turned off.
- When the headset is powered off, insert a 3.5mm audio cable to switch the audio The other end of the cable can be connected to mobile phones, computers and other devices to realize wired connection.
Instructions for
Power On | Long press the ” ” key for 2 seconds |
---|---|
Power Off | Long press the ” ” key for 4 seconds |
Answer the phone | Short press the ” ” key |
Hang up the phone | Short press the ” ” key |
Decline a call | Long press the ” ” key for 1 second |
Music playback | Short press the ” ” key |
Music to suspend | Short press the ” ” key |
The next song | Long press “+” for 3 seconds |
In a song | Long press “—” for 3 seconds |
The volume and | Short press the “+” key |
The volume reduction | Short press the `—” key |
Voice prompt
Power On | power on |
---|---|
Power Off | power off |
The bluetooth pairing | pairing |
The connection is successful | connected |
disconnect | disconnected |
Phone calls reminding | Cell phone rings |
Low power alarm | battery low |
Open the noise reduction | ANC ON |
Close the noise reduction | ANC OFF |
Charging
- Connect the Type-C plug of the charging cable to the Type-C port (USB) of the headset Plug into a 5V power outlet. (note: power adapter is not included).
- When the headphone indicator is red on, the headphone is charging. When the headphone is fully charged, indicate The indicator will change from red to blue. FCC Wamning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be install9d and operated with minimum distance 0cm between the radiator and your body.
EUBRIDGE ADVISORY GMBH
Virginia Str. 2 35510 Butzbach,Germany
eubridge@outlook.com
TANMET INT’L BUSINESS LTD
9 Pantygraigwen Road, Pontypridd, Mid Glamorgan, CF37 2RR,UK
tanmetbiz@outlook.com
Manufacturer: Dongguan Shangyuan Electronic Co., LTD
Manufacturers address: Building 4, Hengli Village Development Zone, Hengli
Town, Dongguan City, Guangdong Province
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>