SereneLife IPCAMHD15 Outdoor HD Wireless IP Camera User Guide
- June 9, 2024
- serenelife
Table of Contents
SereneLife IPCAMHD15 Outdoor HD Wireless IP Camera
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss
Warnings
- Proper configuration of all passwords and other security settings is the responsibility of the installer and end user.
- In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
- Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 100 to 240 VAC or 5 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.
- Do not connect several devices to one power adapter as adapter overload may cause overheating or a fire hazard.
- Please make sure that the plug is firmly connected to the power socket.
- If smoke, odor or noise rise from the device, turn of the power at once and unplug the power cable, and then please contact the service center.
Installation Instruction
-
Install “MIPC” APP
Method I: Download APP in: www.mipcm.com/download; Method II: Scan to Download:
Method III : Download “MIPC” APP from APP Store (iOS) or Play Store (Android). -
Register an Account
Open “MIPC” APP, click “register” button, register & log in as instructed (For your account safety & retrive password, we suggest you to bind with email before log in).
-
Add Camera
Click on “+” in top left corner, choose “PTZ cameras” (FIX/Cloud box/ Panoramic), scan the QR code on bottom of the camera, and tap the “Add” button to enter the network connection interface.
-
Select Network Connection
You could choose either “Sound connection” or “Ethernet connection” to connect the camera.
Note :
- Press RESET for 1 second to enter Wi-Fi configuration; press for 10 seconds or longer to restore to factory settings (when you hear a chime, then setting successfully).
- Try “Ethernet connection” if “Sound connection” unsuccessful.
Option 1: Sound connection
a. Click the “Sound connection” icon, setting up Wi-Fi for camera (only
support 2.4GHZ), input the Wi-Fi password;
b. Power on the device (30-60 seconds after you connect the power, you will
hear the chime and the IR light will turn of, now camera is powered on);
c. 1. Click the “Already heard the voice hint” if you hear the chime, and wait
until successfully connected.
2. If no chime heard, please press the RESET button for 1 second, you will
hear the voice prompt say “Waiting for receiving the wireless configuration”,
click “Already heard the voice hint”, and wait until successfully connected.
Option 2: Ethernet connection
- a. Click the “Ethernet connection” icon;
- b. Power on the device, connect the camera to router with Ethernet cable (camera will be powered on in 30-60 seconds);
- c. Add the matched device until set up successfully.
Questions? Comments?
We are here to help!
Phone : (1) 718-535-1800
Email : support@pyleusa.com
Customer Support
FAQ
What if the camera cannot connect to Wi-Fi?
– Check if your Wi-Fi password contains special characters such as spaces,
commas, periods, etc, which may not be recognized by the camera.
– The camera is only available to 2.4GHz Wi-Fi, not 5GHz Wi-Fi. Please check
and see your Wi-Fi frequency band of the router.
– Keep your mobile phone as close to the camera as possible, and keep your
camera as close to the router as possible.
– Poor Wi-Fi signal may result in failure to connect to your camera. You can
use a Wi-Fi Range Extender which will extend the Wi-Fi signal and wireless
coverage of existing wireless networks.
– If you have an Ethernet cable at home, please try to set up the camera with
it, then follow the directions on the APP to change into a Wi-Fi network.
– If you fail to connect the camera, please follow these steps and try again:
1. Remove power cord. Then, re-plug it in.
2. Press and hold the RESET button for over 10 seconds to restore the camera
to factory settings when you hear the voice prompt and the IR light turns on.
3.Set up the camera once more when you hear the voice prompt.
After inserting the SD card properly, why does the camera still not have any recorded videos?
– The camera needs to be inserted when the camera is of.
– After the camera is inserted with SD card, the video recording function
needs to be turned on manually.
– Steps: Settings-SD Card-Activate. Then set up for recording in Settings-
Record-Continuous Recording/Motion-Detection, enable the recording and save
the settings.
APP can’t receive the alarm notification?
– The camera has motion detection and alarm function, but it needs manual setup. Steps: Enter the camera “settings”, select “Notifications”, enable the motion detection feature and save the settings.
What if I forget my account & password?
– You can find your account & password with the binding email, it will not be found if not binding with email.
How can I see the recorded video? Can I put the SD card in the computer to playback?
– For your privacy and security, video files are encrypted, it must be playback through mobile phone APP or computer APP, and it cannot be played directly on the computer, you need to export the video through SDtool, a special video export tool. The SDtool can be downloaded from www.mipcm.com.
How does the camera restore to factory settings?
– Press and hold the RESET button for 10 seconds, you will hear the voice prompt “Restore the factory settings successfully”, now camera starting to restore, it will finish about 60 seconds, then you will hear a chime (Do not power of during restore procedures).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>