ABRITES Diagnostics For Toyota-Lexus-Scion Online User Manual
- June 9, 2024
- ABRITES
Table of Contents
Abrites Diagnostics for Toyota/Lexus/Scion Online User Manual
2022
ABRITES DIAGNOSTICS
FOR TOYOTA/LEXUS/SCION ONLINE
User manual
version 1.1
Important notes
The Abrites software and hardware products are developed, designed and
manufactured by Abrites Ltd.
During the production process we comply to all safety and quality regulations
and standards, aiming at highest production quality. The Abrites hardware and
software products are designed to build a coherent ecosystem, which
effectively solves a wide range of vehicle-related tasks, such as:
- Diagnostic scanning;
- Key programming;
- Module replacement,
- ECU programming;
- Configuration and coding.
All software and hardware products by Abrites Ltd. are copyrighted. Permission is granted to copy Abrites software files for your own back-up purposes only. Should you wish to copy this manual or parts of it, you are granted permission only in case it is used with Abrites products, has “Abrites Ltd.” written on all copies, and is used for actions that comply to respective local law and regulations.
Warranty
You, as a purchaser of Abrites hardware products, are entitled of a two-year
warranty. If the hardware product you have purchased has been properly
connected, and used according to its respective instructions, it should
function correctly. In case the product does not function as expected, you are
able to claim warranty within the stated terms. Abrites Ltd. is entitled to
require evidence of the defect or malfunction, upon which the decision to
repair or substitute the product shall be made. There are certain conditions,
upon which the warranty cannot be applied.
The warranty shall not apply to damages and defects caused by natural
disaster, misuse, improper use, unusual use, negligence, failure to observe
the instructions for use issued by Abrites, modifications of the device,
repair works performed by unauthorized persons. For example, when the damage
of the hardware has occurred due to incompatible electricity supply,
mechanical or water damage, as well as fire, flood or thunder storm, the
warranty does not apply. Each warranty claim is inspected individually by our
team and the decision is based upon thorough case consideration.
Read the full hardware warranty terms on our website.
Copyright information
Copyright:
- All material herein is Copyrighted ©2005-2021 Abrites, Ltd.
- Abrites software, hardware, and firmware are also copyrighted
- Users are given permission to copy any part of this manual provided that the copy is used with Abrites products and the “Copyright © Abrites, Ltd.” statement remains on all copies
- “Abrites” as used in this manual synonymous with “Abrites, Ltd.” And all it’s affiliates
- The “Abrites” logo is a registered trademark of Abrites, Ltd.
Notices:
- The information contained in this document is subject to change without prior notice. Abrites shall not be held liable for technical/editorial errors, or omissions herein.
- Warranties for Abrites products and services are set forth in the express written warranty statements accompanying the product. Nothing herein should be construed as constituting any additional warranty.
- Abrites assumes no responsibility for any damage resulting from the use, misuse, or negligent use of the hardware or any software application.
Safety information
The Abrites products are to be used by trained and experienced users in
diagnostics and reprogramming of vehicles and equipment. The user is assumed
to have a good understanding of vehicle electronic systems, as well as
potential hazards while working around vehicles. There are numerous safety
situations that cannot be foreseen, thus we recommend that the user read and
follow all safety messages in the available manual, on all equipment they use,
including vehicle manuals, as well as internal shop documents and operating
procedures.
Some important points:
Block all wheels of the vehicle when testing.
Be cautious when working around electricity.
- Do not ignore the risk of shock from vehicle and building-level voltages.
- Do not smoke, or allow sparks/flame near any part of the vehicle fuel system or batteries.
- Always work in an adequately ventilated area, vehicle exhaust fumes should be directed towards the exit of the shop.
- Do not use this product where fuel, fuel vapours, or other combustibles could ignite. In case any technical difficulties occur, please contact the Abrites Support Team by email at support@abrites.com.
List of revisions
| Date | Chapter | Description | Revision |
|---|---|---|---|
| 26.04.2022 | ALL | Document created. | 1 |
| 24.11.2022 | 3 | Update | 1.1 |
Introduction
Congratulations on choosing our wonderful product!
The “Abrites Diagnostics for Toyota/Lexus/Scion Online” is an online server
based Abrites software for Toyota, Lexus and Scion vehicles.
With the help of this software you can perform key learning operations of
Toyota 2018+ Camry/Corolla, CH-R, Prius, Mirai, RAV4, Avalon, Lexus RX, Lexus
RXL, Lexus ES, Lexus LS and Lexus UX vehicles. For proper operation of your
diagnostic software you will need a corresponding interface for connection
between your PC and vehicle named “AVDI”.
AVDI is an interface produced by Abrites Ltd. intended to act as an interface
between the PC and the electronic control units.
AVDI should be used with ABRITES software produced by Abrites Ltd.
ABRITES is a trade mark of Abrites Ltd
Vehicle diagnostics with Abrites for Toyota
2.1 Scope of the manual
This document describes the usage of Abrites Diagnostics for Toyota / Lexus /
Scion Online. The document is applicable for the latest software version. In
this manual we suppose that the software for your AVDI interface is already
installed. Please refer the “AVDI Common User’s Manual” in case it is not.
System requirements:
- Minimum system requirements – Windows 7 SP1 + 2GB RAM (recommended 4GB)
2.2 Getting Started
You can start Abrites Diagnostics for Toyota/Lexus/Scion Online by starting
the Abrites Quick Start application and selecting Toyota. On the 2nd page of
the Toyota option, you need to select the following button. When the Abrites
Diagnostics for Toyota/Lexus/Scion Online application is started the main
screen of the application will appear where you can select the brand desired-
Toyota or Lexus:
If Toyota is selected, you will have the possibility to select the model
you’re working on:
If Lexus is selected, the following models will appear for selection:
Special Functions
The ABRITES Diagnostics for Toyota/ Lexus/ Scion Online offers currently Key
Learning for Toyota/Lexus models 2018+. Please, note that depending on the
version you have purchased some of these functions may not be available in
your configuration.
In this case a message will inform you that you need to acquire an additional
license.
3.1 Special Function “Key Learning”
When the “Key learning” special function is selected it is very important to
follow the exact directions of the application.
Once the model is selected, you have the option to learn keys under the “Key
Learning” menu:
The Key Learning functionality for Toyota supports the following models both
for spare key programming and when all working keys are lost. This solution
covers said models, regardless of the market on which they are offered – all
versions of the models are supported (US, European, UK, Asia). Smart system
reset is NOT needed, nor a connection to Toyota servers. Depending on the
transponder type in the vehicle, either a DST-AES or a HITAG-AES emulator will
be required. ZN002.
– Corolla 2018+ (HITAG AES)
– Camry 2018+ (HITAG AES)
– Highlander 2020+ (HITAG AES)
– Toyota CH-R 2018+ (DST AES)
– Prius 2018+ (DST AES)
– RAV4 2018+ (DST AES)
– Avalon 2018+ (DST AES)
– Lexus RX (DST AES)
– Lexus RXL (DST AES)
– Lexus ES (DST AES)
– Lexus LS (DST AES)
– Lexus UX (DST AES)
Starting the Key Learning procedure is executed via OBDII, and consists of the
following easy steps.
These steps are the same when using either of the licenses – TN011, TN012 and
TN013. The only difference is the key transponder type used:
- Press and hold the START button to begin the procedure
- Switch IGN ON and then OFF while leaving hazard lights ON
- Confirm whether you want to prepare a Master Key emulator
- Reading and modifying the required data
- Insert the HT-AES (TA64) key emulator in the ProTag programmer
- TA64 has been detected and is being prepared as Master Key
- Use the prepared TA64 to switch IGN ON
- Leave IGN to the ON position and open the driver’s door
- Touch the START button with the TA64
- TA64 detected as Master Key
- Use the new key to touch the START button and learn it
- The new key is detected
- The key is now learned and the procedure has successfully finished
Additional Connections
The software used to require Internal CAN Connection with the use of CB012,
wehis is not required anymore. In some rare cases the software might ask for
internal CAN Connection using CB012. All of the Toyota/Lexus models that are
covered by the TN011, TN012 and TN013 licenses share the same Smart System
pinout when connecting to the internal CAN BUS where pin 1 is the CAN H and
PIN 2 is CAN L. This is what the connector looks like and what pins to connect
to when working with CB012:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>