hama 00176592 Smart Radiator Thermostat Instruction Manual

: June 4, 2024
: Hama

Table of Contents

Operating Instructions
Controls and displays
Explanation of warning symbols and notes
Package contents
Safety instructions
Getting started
Fitting on the radiator valve
Installing the app
Outward mode
Technical data
Care and Maintenance
Recycling information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

hama 00176592 Smart Radiator Thermostat

Operating Instructions

Thank you for choosing a Hama product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

Controls and displays

Control dial / On/Off button
LED display
WLAN connection
Mode
Heating phase
Low battery level
Temperature
Blue status LED
Red status LED
Reset / Pairing
Micro-USB socket

Explanation of warning symbols and notes

Risk of electric shock
This symbol indicates a risk of electric shock from touching product parts carrying hazardous voltage.

Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note
This symbol is used to indicate additional information or important notes.

Package contents

1 x radiator thermostat
2 x AA batteries
1 x adapter set
2 x radiator thermostats
1 x central control unit
x AA batteries
2 x adapter sets
1 x USB power supply unit

Safety instructions

The product is intended for private, non-commercial use only.
Use the product only for the intended purpose.
Protect the product from dirt, moisture and overheating and use it in dry rooms only.
The product is intended only for use inside buildings.
Only use the article under moderate climatic conditions.
As with all electrical products, this device should be kept out of the reach of children.
Do not operate the product outside the power limits specified in the technical data.
Do not use the product in areas in which electronic products are not permitted.
Do not use the product in a damp environment and avoid splashing water.
Do not drop the product and do not expose it to any major shocks.
Do not modify the product in any way. Doing so voids the warranty.
Keep the packaging material out of the reach of children due to the risk of suffocation.
Dispose of packaging material immediately in accordance with the locally applicable regulations.
Route all cables so that there is no risk of tripping.
Do not bend or crush the cable.
Always pull directly on the plug when disconnecting the cable, never on the cable itself.

Risk of electric shock

Do not open the device or continue to operate it if it becomes damaged.
Do not use the product if the
C adapter, the adapter cable or the mains cable are damaged.
Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.

Getting started

Warning – Batteries

When inserting batteries, note the correct polarity (+ and – markings) and insert the batteries accordingly. Failure to do so could result in the batteries leaking or exploding.
Only use batteries (or rechargeable batteries) that match the specified type.
Before you insert the batteries, clean the battery contacts and the polar contacts.
Do not allow children to change batteries without supervision.
Do not mix old and new batteries, or batteries of different types or from different manufacturers.
Remove the batteries from products that are not being used for an extended period (unless these are being kept ready for an emergency).
Do not short-circuit batteries.
Do not charge batteries.
Do not burn batteries.
Keep batteries out of the reach of children.
Never open, damage or swallow batteries or allow them to enter the environment. They can contain toxic, environmentally harmful heavy metals.
Remove spent batteries from the product and dispose of them without delay.
Avoid storing, charging and using in extreme temperatures and at extremely low atmospheric pressures (such as at high altitudes).
Press the battery symbol on the housing and pull the housing cover upwards over the control dial.
Remove the spent batteries and dispose of them if required. Insert two new batteries of type AA. Take care to ensure the correct polarity as shown in the diagram in the battery compartment.
“LA” flashes on the display.
Close the battery compartment by pushing the housing cover back onto the control dial.
Wait for around 30 seconds until the “LA” display lights up solid. The thermostat can now be fitted to the radiator.

Fitting the adapter

Thanks to the union nut, the thermostat can be fitted to all valves with the thread dimensions M30 x 1.5 mm from the most common brands such as
With the adapters included in the extent of delivery, the device can also be fitted to radiator valves of type Danfoss RA, Danfoss RAV, Caleffi and Giacomini.

To fit the attachments, please follow the instructions below for the respective part. Danfoss RA and Danfoss RAV

While fitting, ensure that the pins inside the adapter cover the same position as the notches on the valve.
Fully attach the adapter appropriate for your valve.
During fitting, you may need to use a screwdriver and bend the adapter slightly in the area of the screw bushing. This will enable the adapter to be pushed more easily onto the valve. After locking it onto the body of the valve, secure the adapter using the enclosed screw and nut.

Danfoss RAV

On Danfoss RAV valves, the tappet extension must be placed on the valve pin before fitting.

Caleffi

Please place the Caleffi adapter directly on the valve.

Giacomini

To fit the Giacomini adapter, please first attach the top piece, then place the tappet extension on the valve pin, and then finally secure the piston to the thermostat.

Fitting on the radiator valve

Never apply force during the fitting process. This can damage your device.
Ensure that the radiator is switched off and has cooled down before starting to fit any attachments.
Place the thermostat straight on the valve and tighten the union nut.
Fit the thermostat so that the LED indicator remains visible for you.
Press the control dial (1). The “LA” display starts to flash. The radiator thermostat now carries out an adaptation run.
Once the adaptation run has been carried out, the display shows the current temperature. If it does not, carry out the above steps again.

Fitting the central control unit

Warning

Only operate the product from a socket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
Disconnect the product from the power supply using the On/Off switch – if this is not available, unplug the power cord from the socket.
If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
If you will not be using the product for a prolonged period, disconnect it from mains power.
Connect the enclosed micro-USB cable to the micro-USB socket and the USB power supply unit.
Connect the power supply unit to a properly installed and easily accessible mains socket.
The LEDs start to flash.

Installing the app

Download the “Hama Smart Solution” app using the QR code and install it.

Integrating devices into the Hama Smart Solution app
Pairing the central control unit

To pair the radiator thermostat with the Hama Smart Solution app, you must first integrate the central control unit into the Hama Smart Solution app.
Ensure that the central control unit is connected to the power supply and that the LEDs are flashing.
Open the app and select “My home” at the bottom left-hand edge of the screen.
Then tap the “+” at the top right-hand edge of the screen and select the category “Heating control”.
Confirm in the app that the central control unit is flashing.
Now enter the name of your WiFi network and the password. Confirm your entry with “OK”. The central control unit is now connected.
Once successfully connected, the red LED lights up solid and the app confirms that the central control unit has been connected. You can now assign it a different name if you wish.
Touch “Done”. The procedure is complete.
Now connect the radiator thermostats with the central control unit.
To do this, select your central control unit in the app from the list of found devices.
The following screen appears:

Radiator thermostat pairing

Turn the control dial on the radiator thermostat to the leftuntil the display shows “OF”.
The “OF” becomes visible if you look at the display from the direction of the control dial. If no “OF” appears, turn the dial in the opposite direction.
If the display goes out, turn the dial slightly until the display lights up again.
Press and hold the control dial for around 5 seconds until the “OF” display goes out and “- -” appears.
In the app, press “Add secondary device”.
Confirm with “LED is already flashing”.
In the “Find device” screen in the app, you will now see all of the thermostats that the central control unit could find.
The search takes around 15 seconds. Over large distances or if the connection is poor, this process may take up to 2 minutes.
Press “Done” once your thermostats have been found.
You can now rename your thermostats if you wish to by pressing on the pen symbol next to the device name.
Press “Done” to end the integration process.
Slide the “Activate” button at the bottom edge of the screen from right to left to enable the radiator thermostat control.
You can now set and configure your radiator thermostat using the app.

Configuring thermostats

For simple temperature setting, there are four different operating modes available under “Program” for each day of the week.
This gives you the option of pre-setting the temperature of your radiator automatically at various times of the day. The programs pre-set in the app mean you can also carry out further automatic temperature changes.
Under “Settings”, you can activate the limescale protection, anti-frost protection, window open detection, child safety and temperature calibration functions.
These functions, along with a few other setting options, are explained below.
Under “Settings”, you can activate the limescale protection, anti-frost protection, window open detection, child safety and temperature calibration functions.
These functions, along with a few other setting options, are explained below.
In Off mode, the display shows .
If the temperature falls below 5°C, the thermostat automatically activates the heating.
Heating continues until the temperature reaches 8°C. The thermostat then switches back to Off mode. Window open detection
If a window is opened while the heating is on, the radiator thermostat automatically stops the heating process if the temperature falls rapidly. (Temperature drop 6°C within 4 min)
“OP” appears in the display. As soon as the window is closed and the temperature has risen again by 2°C, the radiator thermostat automatically returns to normal operation.

Outward mode

The outward mode can be activated in the app. As soon as this is activated, “LH” appears on the display.
If this mode is active, the set temperature is automatically dialled down to 16°

Display turning

First move the dial to the OF position. Then, by pressing the control dial 5 times, the display can be rotated around 180°.
Press and hold the button on the central control unit for around 5 seconds. As soon as the LEDs start to flash, you can, as described in Section 4.6 Integrating devices into the Hama Smart Solution app, start a further pairing attempt.
Press and hold the control dial on the radiator thermostat for around 5 seconds until “- -” appears on the LED display. Ensure that the thermostat previously displayed “OF”.
You can now, as described in Section 4.6 Integrating devices into the Hama Smart Solution app, start a further pairing attempt.

Extended usage options with scenarios
Scenarios and automated sequences that can be created in the app allow various combination options and usage options for these products, depending on the SmartHome products in your home.
Programming is always carried out via the app (see Section 4 of the App Guide) and will be offered/suggested to you on an individual basis.

Extended usage option

Technical data

Power supply to the central control unit 5V 1A
Power supply to the radiator thermostat 2 x AA batteries
Connection of the radiator thermostat M30 x 1.5

Care and Maintenance

Disconnect the device from the mains before cleaning and during prolonged periods of non-use.Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.

Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Service and Support

Please contact Hama Product Consulting if you have any questions about this product.
Hotline: +49 9091 502-0 (German/English)
Further support information can be found here: www.hama.com

Recycling information

Note on environmental protection:After the implementation of the European Directives 2012/19/EU and 2006/66/EU in the national legal system, the following applies: electrical and electronic devices, as well as batteries, must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries to the Hama GmbH & Co KG hereby declares that the radio equipment type [00176592, 00176593] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:www.hama.com -> 00176592, 00176593 -> Downloads.

Hama 00176592 Smart Radiator Thermostat Instruction Manual