Godox M600Bi BiColor LED is Brighter and has Touchscreen User Manual

KNOWLED M600 Bi
Knowled M600Bi Bi-color LED Light
Instruction Manual

Safety Instructions and Attentions

First of all, as the most basic principle: This product is a professional lighting set equipment and should be used by professional lighting engineers or under the guidance of professionals. Basic safety attentions must always be followed during use, as follows:

1. Before use, please read and understand these instructions and attentions.
2. Professional lighting is prohibited for children. When children are near, parents or accompanying persons must supervise closely to prevent children from personal injury due to collision with lamps or private use of lamps.
3. This lighting product is not ordinary lighting product and cannot be used for general lighting. Anyone who has suffered eye damage or has sensitive eyes should avoid using this product.
4. When the lamp is on, it must be used with care. Do not touch high-temperature parts, such as LED lamp beads, to avoid burns.
5. When the lamp is on, it is forbidden to look directly at the lamp beads under any circumstances. Strong light should be used under the guidance of professional lighting engineers. Avoid prolonged exposure to strong light under any circumstances. If eye discomfort, please turn off the lamp in time, suspend use, and see a doctor immediate-ly.
6. If the lamp bead is damaged or deformed by heat, stop using this equipment, and contact the manufacturer, service agent or qualified maintenance personnel to replace the lamp bead in time to avoid accidents.
7. This product is only suitable for use in -20C to 40C operating environment and normal humidity environment.
8. Do not use damaged equipment or accessories, and wait for professional maintenance personnel to check and repair to confirm being normal before use.
9. During using, if the casing of this product is broken due to being dropped, squeezed or subjected to strong impact, please do not use it, so as to avoid electric shock injury due to contact with internal electronic components.
10. If an extension cord is required, please use an extension cord with a current rating greater than or equal to that of the equipment. If an extension cord is rated less than the equipment, overheating may result.
11. Some products have long power cords, please place the power cords properly and keep them in a safe place. Avoid contacting the power cord with overheating surfaces, avoid improper placement that could cause pulling damage, or trip on-site personnel. Please use the certified power cord from the original manufacturer. If the product is damaged by using a non-certified power cord, it will not be repaired by our factory.
12. Be sure to unplug equipment from the power outlet before cleaning and repairing. When not in use, do not pull the power cord to unplug the equipment. For normal power-off, please hold both ends of the plug of the equipment with your hands and pull the plug out of power outlet. This equipment needs to be connected to a ground-ed outlet.
13. This equipment is not waterproof, please keep it dry and do not immerse it in water or other liquids. The equipment should be installed in a dry and ventilated place, and avoid using it in rainy, humid, dusty or overheated environments. Do not place any objects on the lamp or let liquid flow into the lamp to avoid accidents.
14. Do not disassemble the product without permission. If the product fails, it must be checked and repaired by authorized maintenance personnel.
15. Before storing, make sure that the equipment has cooled down completely. For storage, unplug the power cord from the equipment. The equipment should be placed in the carrying case or in a ventilated dry place.
16. Do not place equipment near flammable and volatile solvents such as alcohol and gasoline.
17. Do not use accessories that are not recommended by our factory to avoid fire, electric shock or personal injury.
18. When cleaning, do not wipe it with a damp cloth, please use a dry cloth or a soft cloth to wipe the dirt of the equipment. 1
19. Please take off the protective cover before using.
20. This product complies with ROHS, CE and FCC certification, please refer to the relevant national standards for use and operation.
21. The safety instructions are formulated according to the strict testing of the factory, and the design and specifications of the equipment are subject to change without prior notice. For latest product information, please check the GODOX website and view latest electronic instruction.
22. Some products have built-in lithium batteries. Please use specified chargers, and use them within a proper range of the specified voltage and temperature according to the correct operating instructions.
23. Some products are battery powered. Do not use any batteries, power sources or accessories not specified in the instructions for such products. Keep batteries and other accessories out of the reach of children and infants. In the instance that a child or infant swallows a battery or accessory, immediate emergency medical attention is required. If the battery leaks, becomes discolored, deformed, emits smoke, or emits an abnormal odor, remove it immediately. Be careful during removal to avoid bums. Continued use could result in fire, electric shock, or burns. Do not use any deformed or modified batteries. Do not disassemble or modify this product or battery. Do not heat or solder the battery. Keep the battery away from fire or water. Do not incorrectly insert the positive and negative ends of batteries, or mix old and new batteries or batteries of different types together.
24. 0ne-year warranty period, accessories such as consumable batteries, adapters, power cords, etc. are not covered by this warranty.
25. If it is found that the equipment is repaired without authorization, the one-year warranty period will be cancelled and relevant fees will be charged for maintenance.
26. Machine failures caused by non-standard operation are not covered by the warranty. keep these instructions!

Foreword
Thank you for purchasing! Godox M600Bi is a LED Light product with superior performance. It has a separation design of light body and controller, high power, thousand-bit brightness adjustment , various dimming curves and 2800K- 6500K CCT, quite suitable for large photo studios, broadcast studios, Outdoors or large-scale field scenes.
Main Features

• 600W input power to create bright light output.
• Brightness adjustment is accurate to 0.1%, controlling the brightness in subtle scenes.
• 4 dimming curves: linear, S-curve, exponential, and logarithmic.
• Wide CCT range from 2800K to 6500K.
• Bowens mount is perfectly compatible with more optical accessories.
• Various professional control methods: Bluetooth control/DMX512 remote control/2.4G wireless control.
• Super high color rendering index: CRI: TLCI: 1.97
• 21 simulated scenes light effects: flash, lightning, TV, broken bulb,candle, fire, firework, etc.
• Two power supply methods: AC power supply (100V-220V)and V-mount battery power supply (14.8V or 26V).
• The side with yellow battery removal button supports unilateral power supply.
• 2.4 inches TFT panel,4 buttons, 1 knob, clear UI interface.

Warning
Always keep this product dry. Do not use in rain or in damp conditions.
Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
Keep out of reach of children.
As this product do not have waterproof function, please take measures of water-proof in rainy or damp environment.
Do not leave or store the product if the ambient temperature reads over 40°C.
Do not use the product in the presence of flammable gases, chemicals and other similar materials.
CAUTION: Hot parts!When the product is always on and flickering,please do not touch the high temperature part of the LED head.
When replacing product accessories,please turn off the LED light and perform a cold cut.
The light source contained in this luminaire shall only be replaced by the manufac-turer or his service agent or a similar qualified person.
The lamp shall be changed if it has become damaged or thermally deformed.
The luminaire is intended for professional use only.

Name of Body

1. Bowens Mount
2. LED Bead
3. Metal U-bracket
4. Mount Fixing Pusher
5. DC INPUT Port
6. Handle Direction Adjustment Button
7. Locking handle
8. Sleeve Knob

Controller

9.Type-A USB Port
10.Black Battery Removal Button
11.V-mount Battery Box
12.AC INPUT Port
13.48V DC Port
14.Yellow Battery Removal Button
15.DMX OUT XLR Port| 16.DMX IN XLR Port
17. Button
18DC OUTPUT Port
19.Fan Switch Button
20.Power Switch Button
21.SET Adjustment Knob
22.Menu Button
---|---

Remote Control ( Separately Sold Accessory)

23.Power Switch Button
24.S ET Setting Button
25.Reduction Button| 26.CH/GR Button
27.Increase Button
28.RST- Reset Mark
---|---

(Press Reduction Button and Increase Button simultaneously to reset)

What’s in the Box

Separately Sold Accessories
Better shooting effects and using experience matched with following accessories: Fresnel Attachment for COB LED lights FLS10, Safety Wire Rope and RC-A6 Remote Control.

Installation and Disassembly Guide

1. Connect the controller and the light body Press and hold the spring latch button of the connecting cord, insert the connecting cord into the DC INTPUT Port of the light body. Then continue press and hold the button to insert the other end of the connecting cord into the DC OUTPUT Port of the controller to complete the connec-tion.
   

2. Mounted on the tripod
   Adjust the light body to a proper angle, rotate the screw of sleeve knob to install the light body on the tripod, then rotate the screw of sleeve knob to fix the light body on the tripod. The inclination angle of the light body could be adjusted by loosening the bracket angle adjustment handle and then screwing down the handle afterwards. Note: The tripod belongs to separately sold accessories.
   Tips: Press the handle direction adjust-ment button to adjust the handle by 360°.

3. Mounted on the light stand
   Loosen the handle of the controller clamp, then insert the light stand and rotate the handle to tighten.Finally, insert the V port of the controller into the clamp slot.
   Tip: Press and hold the mount fixing pusher can easily remove the controller.

4. Installation and disassembly the lamp cover
   Installation: Press the Mount Fixing pusher top-down, put the lamp cover on Bowens Mount, and rotate clockwise to tighten it. Disassembly. Press the Mount Fixing pusher top-down, then rotate counter-clockwise to remove it.
   Note: Make sure to remove the lamp cover before use to avoid overheating damage. Put on the lamp cover to protect the lamp when not in use.

5. Installation and disassembly the standard reflector Installation: Press the Mount Fixing pusher top-down, put the standard reflector on Bowens Mount, and rotate clockwise to tighten it. Disassembly: Press the Mount Fixing pusher top-down, then rotate counter-clockwise to remove it.

Connected to DMX Controller
The Connection operation diagram of Controller and DMX Controller is as follows:

Power Supply

1. AC Power Supply
   
   Note: Please press the latch button when installing or disassembling the power cord and connecting cord.

2. V-mount battery power supply
   
   Note: The light can be supplied by 14.8V or 26V V-mount battery. Only the side with yellow battery removal button supports unilateral charging, one with. When it is powered by two batteries and one of which is low, the device still can’t work normally even if the other one is full. The corresponding battery icon will blink in low battery mode. It is recommended to check whether both batteries have sufficient power when using two batteries.

Display Screen

Connected to DMX Controller

1. Turn On/Off
   Press the controller < > Button for 1 second after connecting to the power supply to turn on or off.

2. Brightness Adjustment (thousand-bit adjustment)
   Turn the SET adjustment knob on the main interface to adjust bright-ness from 0% to 100%, with an increment of 0.1% in each level. Rotate clockwise to increase brightness, and counterclockwise to decrease brightness. The bright- ness will increase or decrease by 0.1% unit in normal rotation speed; and increase or decrease by 1% unit in rapid rotation speed; and increase or decrease by 10% unit if press and rotate.

3. CCT Adjustment
   Short press SET adjustment knob on the main interface to make the arrow aimed at the CCT value, then turn it to adjust CCT from 2800K to 6500K, with a increase or decrease of 100K in normal rotation speed and 500K in rapid rotation speed.

4. Menu Setting
   Short press < MENU > Menu Button to enter the menu interface, displayed in order with Wireless, Bluetooth, DMX, Fan, Dimmer, Screen Bright, Language,Reset, Version & Update. Turn and short press the SET adjustment knob on the menu interface to select and enter the corresponding setting options interface.
   4.1 Wireless
   The Wireless interface is displayed in order with Wireless , CH, GR and ID. Short press & turn the SET adjust-ment knob to complete the settings of Wireless Switch, Channel, Group and ID.

4.2 Bluetooth
The Bluetooth Setting interface is displayed in order with Bluetooth , Reset and MAC. Short press & turn the SET adjust-ment knob to complete the settings of Bluetooth Switch and Bluetooth Reset.

For more smartphone APP opera-tions, please open the ‘help’ in “GodoxLight” APP to gain detailed guidance.
http://www.guteleben.com/html/dl_app/c_ble/GodoxLight/index.html
Note: the APP can be used directly on the firstly installed device (smartphone or tablet). When changing to other mobile device, the light shall be reset before the normal usage of APR

4.3 DMX
The DMX Setting interface is displayedwith Mode and Address. Short press the SET adjustment knob to choose between mode and address,then turn it to set mode and address.

DMX Practical Form

2
3| Color
temperature| 0 — 65535| 2800K — 6500K
4
4| FX 16bit| 1| Brightness| 0 — 65535| 0% — 100.0%
2
3| Light
effect type| 0 — 36| Flash
37 — 73| Lightning
74 — 109| Broken Bulb
110 — 146| TV
147 — 183| Candle
184 — 219| Fire
220 — 255| Fireworks
4| Light
effect gear| 0-85| I
86-171

II

|
172-255| III
5| ULTIMATE
8bit| 1| Brightness| 0 — 255| 0% — 100%
2| Mode
selection| 0 — 51| CCT
52-255| FX
3| Mode Parameter (refer to table below)
4

CCT Mode Parameter

FX Mode Parameter

2
3| Mode
selection| 0 — 51| OCT
52-255| FX
4| Mode Parameter
(refer to table below)
5

CCT Mode Parameter

FX Mode Parameter

Calculation formula:
Brightness

4.4 Fan
Turn the SET adjustment knob on the Fan Setting interface to choose Cooling Mode, Off Mode, Low-Speed Cooling Mode, High-Speed Cooling Mode.
Note: Enter mute mode when turning off the fan.

4.5 Dimmer
Turn the SET adjustment knob on the Dimming Curve Setting interface to choose linear/S-curve/exponential/loga-rithmic dimming curve.

4.6 Screen Bright
Turn the SET adjustment knob on the Screen Bright setting interface to choose 1, 2, 3 levels of screen brightness.

4.7 Language
Turn the SET adjustment knob on the Language Setting interface to choose English or Simplified Chinese.

4.8 Reset
Turn the SET adjustment knob on the Restore Factory Setting interface to choose “Yee or “No” and short press to confirm. If you choose “Yes” , the system will initiate resetting program and reset-ting progress bar is displayed on the screen, after which it will return to the main interface.

4.9 Version & Update
The Version Code displayed on the Version & Update interface is the firmware version of the product.

5. Light Effect Setting
Short press > button to enter FX Light Effect interface, turn the SET adjustment knob to choose among 21 effects: flash, lightning, broken bulb , TV, candle, fire and firework.
Note: Short press the SET adjustment knob to change the rate and adjust brightness after choosing one of the above Light Effects.

Status Description
Long Term Use

1. Do not cut off the power immediately when the product is turned off after a long period of operation. The controller will automatically enter cooling state, and ‘System cooling, do not power off immedi-ately ‘ is displayed on the panel. You can cut off the power after system cooling is done and the screen turns black.

Connecting Cord Issue

2. When the connecting cord is not correctly connected to the light or control-ler, a separated icon of connecting cord and device is displayed on the panel. Please check the connecting ports of the controller and light.
   Switch from AC Power Supply to V-Mount Battery Power Supply

3. Unplug the power cord and install V-mount battery then turn on the product.
   
   Note: If you install the V-mount battery before unplugging the power cord, and the brightness value is set higher than the maximum brightness that the battery can be turned on, then you switch to V-mount battery power supply by unplugging the power cord, the light and the controller will automatically power off. The machine can only resume mormal operation after reboot.
   Maximum Brightness in Different States
   CCT mode: Maximum Brightness (%) in Auto Cooling Mode or High-Speed Cooling Mode when supplied by V-mount battery

CCT mode: Maximum Brightness (%) in Fan Off Mode when supplied by V-mount battery

CCT mode: Maximum Brightness (%) in Low-Speed Cooling Mode when supplied by V-mount battery

CCT mode: Maximum Brightness (%) i n different Fan Mode when supplied by AC power

FX mode: Maximum Brightness (%) in different Fan Mode when supplied by AC power

FX mode: Maximum Brightness (%) in different Fan Mode when supplied by V-mount battery

V-mount battery| Auto Cooling| Off| Low-Speed Cooling| High-Speed Cooling
---|---|---|---|---
14.8V(single)| 20%| 20%| 20%| 20%
14.8V(double)| 40%| 25%| 40%| 40%
26V(single)| 30%| 25%| 30%| 30%
14.8V+26V| 50%| 25%| 50%| 50%
26V(double)| 60%| 25%| 50%| 60%

Note: The dimming curve is not adjustable in FX mode, it is linear in default.
The above data is based on 26V 270Wh 10.5Ah battery and 14.8V 150Wh 10.2Ah battery.

Software Upgrade

1. Download the new firmware to the U disk from the official website (http://www.go-dox.com.cn/Downloads.html).
2. Turn off the LED light. Insert the Udisk with new firmware into the USB upgrade port.
3. Turn on the LED Light , and it will automatically enter the upgrading interface.
4.  It will return to main interface after completion.

Notes:

1. New firmware must be downloaded from the official website, and keep only one BIN file in the root directory of the USB disk.
2. The USB port can only support firmware upgrade function.

Over-Temperature Protection
If the temperature of the light body is too high, the Over-Temperature Protection icon flashes on the main interface, the light body can be used normally.
If the temperature of the light body exceeds the limit of Over-Temperature Protection, the Over-Temperature Protec­tion icon flashes on the main interface and the screen works properly after the light goes out in 3 seconds. When the tempera­ture decreases to 50 ° C, the Over-Tem­perature Protection icon disappears, then the light body can resume working.

Fan Troubleshooting

If icon appeared and blinking and fan off icon is also appeared on the display, It might be the fan failure. Please contact with customer service.

Maintenance

This product , except consumables e.g. adapter and power cable , is supported with a one-year warranty.
Maintenance of the light must be performed by our authorized maintenance depart- ment which can provide original accessories.
Unauthorized service will void the warranty.
If the product breaks down or gets wet, please do not use it until repaired by profes- sionals.
If there is anything abnormal during LED light ’ s working, please turn it off immediately and identify the reasons .

illuminance Testing Data.

M600Bi

CCT| Testing Condition| Illuminance Unit| 1m| 3m| 5m
2800K| Bare Light| lux| 16100| 2010| 804
fc| 1500| 187| 74.7
With Reflector| lux| 135000| 12100| 4200
fc| 12600| 1120| 390
3200K| Bare Light| lux| 19500| 2400| 953
fc| 1810| 223| 88.5
With Reflector| lux| 164000| 14300| 5050
fc| 15200| 1330| 469
4300K| Bare Light| lux| 22400| 2750| 1090
fc| 2080| 255| 101
With Reflector| lux| 186000| 16500| 5790
fc| 17300| 1530| 538
5600K| Bare Light| lux| 23900| 2930| 1160
---|---|---|---|---|---
fc| 2220| 272| 108
With Reflector| lux| 198000| 17500| 6170
fc| 18400| 1620| 573
6500K| Bare Light| lux| 23600| 2870| 1140
fc| 2190| 267| 106
With Reflector| lux| 192000| 17100| 6060
fc| 17900| 1590| 563
Collocated with Fresnel lens FLS10

CCT| Testing Condition| Illuminance Unit| 1.5m| 3m| 5m
2800K| Focusing| lux| 107000| 27100| 9360
fc| 9910| 2520| 870
Diffusing| lux| 36000| 9540| 3440
fc| 3340| 886| 319
3200K| Focusing| lux| 129000| 32700| 11300
fc| 12000| 3040| 1050
Diffusing| lux| 43500| 11500| 4160
fc| 4040| 1070| 386
4300K| Focusing| lux| 149000| 37700| 13100
fc| 13800| 3500| 1210
Diffusing| lux| 50400| 13300| 4810
fc| 4690| 1240| 447
5600K| Focusing| lux| 159000| 40100| 14000
fc| 14700| 3730| 1300
Diffusing| lux| 53500| 14200| 5130
fc| 4970| 1320| 476
6500K| Focusing| lux| 155000| 39400| 13700
fc| 14400| 3660| 1270
Diffusing| lux| 52500| 13900| 5020
fc| 4880| 1290| 466

All the above tests are based o n the condition of 100% brightness.

Technical Data

• Product design and specifications are subject to change without notice.

Maintenance
This product, except consumables e.g. cable, is supported with a one-year warranty.
Avoid sudden impacts and the product should be dedusted regularly.
Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by professionals.
Changes made to the specifications or designs may not be reflected in this manual.

FCC Statement
This device complies with part 15 of the FCC R ules . Operation is subject to the follow-ing two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. I f this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user i s encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver .
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction .
Declaration of Conformity:
GODOX Photo Equipment Co,Ltd. hereby declares that the This equipment are in compliance with the essential requirements and other relevant provisions of EU Direc –
tive 2014/53/EU. They are allowed to be used in all EU member states.
For more information of DoC, Please click this web link : https://www.godox.com/DOC/Godox_M600Bi_DOC.pdf

Warranty
Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fillin the following form i n coordination with the seller and safe-keep it. Thank you!

Address
Seller Information| Name
Contact Number
Address
Date of Sale
Note:

Note: This form shall be sealed by the seller.

Applicable Products
The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached, etc.) are not included in this warranty scope.
Warranty Period
The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.
Inapplicable Cases
The guarantee and service offered by this document are not applicable in the following cases: O. The product or accessory has expired its warranty period; C). Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc; ®. Breakage or damage caused by non- authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment; C). The original identifying information of product or accessory is modified, alternated, or removed; ®. No valid warranty card; e. Breakage or damage caused by using illegally authorized, nonstan-dard or non-public released software; (7). Breakage or damage caused by force majeure or accident; ®. Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consump-tion are not the breakage within the maintenance scope.
Maintenance and Service Support Information
The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Product Type| Name| Maintenance Period(month)| Warranty Service Type
---|---|---|---
Parts| Circuit Board| 1 2| Customer sends the product to designated site
Battery| 3| Customer sends the product to designated site
Electrical parts e.g.battery charger, power cord, sync cable, etc.| 1 2| Customer sends the product to designated site
Other Items| Flash tube, modeling lamp, lamp body, lamp cover, locking device, package, etc.| NO| Without warranty

Godox After-sale Service Call 0755-29609320-8062

Wechat
Official Account

http://weixin.qq.com/r/vEPI0F7ERgM5rRqz9xau

GODOX Photo Equipment Co., Ltd.
Add.: B u i l d i n g 2 , Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District, Shenzhen
518103, China Tel:+86-755-29609320(8062) Fax:+86-755-25723423 E-mail: godox@godox.com

www.godox.com
MadeinChina | 705-M600BY-00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>