LAGOFRAME01 Frame for Minted Art Display User Manual
- October 28, 2023
- Lago
Table of Contents
LAGOFRAME01 Frame for Minted Art Display
About your product
The Lago Display is the touchpoint of the Lago ecosystem that affords users the ability to buy, sell, trade, and most importantly enjoy their minted digital artworks. Once wall mounted the display can be controlled with the Lago app, or with the gesture camera (not included). A digital copy of this document, product shelf life, and after-sales service can be accessed online by following this QR code or visiting lagoframe.com/warranty.
CAUTION
- This fitness Display is for use only with Lago Digital, Inc. frame cleat with M4 L38mm screws. Use with other wall mount brackets/stands may result in instability causing injury.
- Do not cover Ventilation openings.
- This equipment is not intended to be used on soft support.
- The mains plug/appliance inlet is used as the disconnect device, The socket-outlet shall be installed near the equipment and shall be easily accessible.
- The DC OUT location which will be connected to the end product shall comply with the requirements of the applicable clause for standard IEC 62368-1
- Protective earthing terminal. The apparatus should be connected to a main socket outlet with a protective earthing connection.
- The symbol indicates AC voltage
- The symbol indicates the DC voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment. The user has the choice
to give their product to a competent recycling organization or to the retailer
when he buys new electrical or electronic equipment.
FCC WARNINGS
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
IC WARNINGS:
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
This Class B digital apparatus complies with Canadian ICES-003.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body. The device for operation in the band 5150–5350 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems.
In the box
- Screen X1
- top frame piece X1
- side frame piece X2
- bottom frame piece X1
- power cord X1
- frame cleat X1
- frame cleat hardware M4 L38mmX6
- Handles X2
- quick start guideX1
- soundbar hook X1
- I/O panelX1
Hanging your LAGO display
- Remove the cleat from the box and attach it to the wall where you’d like your Lago Display to be mounted. Mount the cleat with the creased edge facing upwards and outwards. Use the included hardware(M4 L38mm) to mount in at least 4 of the 6 horizontal slot locations, including the top 2 slots. Make sure your Lago Display is mounted into studs or using drywall anchors.
- Remove the Lago Display from the box using the handles on the back of the product, and mount the display onto the cleat using the notches in the tops of the handles. Do not lift the product from any other location, as this may damage the display.
Turning on your LAGO display
- Use the provided cable to provide power to the Lago Display.
First, plug in the cord to the “AC IN” input on the back of the display, then plug the cord into a wall outlet or the Lago Battery. The display will turn on automatically.
Mounting your LAGO sound bar
Note:
auxiliary products must be attached to the display before the frame is mounted
onto the display. If the frame is already on the display, remove it before
attaching auxiliary products.
- Attach the soundbar cleat to the back of the soundbar with the provided screws.
- Plug the soundbar into the display at the “DC OUT” location.
- Hang the soundbar to the back of the display using the 4 holes on the cleat and the 4 screws on the back of the bottom of the display.
Note:
auxiliary products must be attached to the display before the frame is mounted
onto the display. If the frame is already on the display, remove it before
attaching auxiliary products.
- Plug your gesture camera into the display.
After attaching the frame, the gesture camera will attach magnetically to the center of the bottom frame part.
Attaching your frame to your display
Note:
Do not attach your frame until your display is mounted with all auxiliary
products prepared. Because the frame sits flush with the mounting surface, the
display rear will not be accessible after frame installation.
- Remove the top frame part from the box and place it on the top edge of your display.
- Remove the left and right frame parts from the box and place them on the sides of your display. Use the magnetic mortise and tenon joints to connect the side frame parts to the top part.
- Remove the bottom frame part from the display and slide it between the bottom tenons from the right and left frame parts.
Connecting to your LAGO display
- Download the Lago app from the App Store or Google Play Store and create an account.
- Scan the QR code on the screen to pair with your display, and follow the quick start instructions in the Lago app.