kindoo KIN D 2.0 DC or AC Power Supply Installation Guide

KIN D 2.0 DC or AC Power Supply
Installation Guide

KIN D 2.0 DC or AC Power Supply

READ CAREFULLY THIS ENTIRE MANUAL BEFORE STARTING ANY INSTALLATION

Note:

1. Specifications subject to change without notice.
2. Tech Support will only be provided where product installation guidelines have been followed.

Package Contents

• KIN D 2.0 x 1
• Metallic PIN with double sided tape x 1
• Wire caps x 5
• Diode 1N4002 x 1

Typical Configuration

Internet required for phone
No Internet required for KIN D 2.0

KIN D 2.0 Specifications

Power Requirement 12 – 24 V (DC or AC)
KIN D 2.0 Max Current Draw 200 mA
Operating Temperature -40˚C to 85˚C [-40˚F to 185˚F] Dimensions 55 mm (L) x 27 mm (W) x 14 mm (H) [2.16 in (L) x 1.06 in (W) x 0.55 in (H)] Weight 30 g [1 oz] Emission Range Up to 20 m [65 ft] Dry Relay Contacts 2 A
Emission Frequency 2.4 GHz
Warranty 1 year

KIN D 2.0 Installation

1. Powering up KIN D 2.0
   The KIN D 2.0 will operate on a DC or AC power supply (not provided) within the range of 12 to 24 volts. If the KIN D 2.0 and attached device are required to operate in the event of a power outage, a ‘Battery Backed- Up Power Supply’ is recommended. If the attached device requires more than 0.5 AMPS of current to operate, a heavy duty power supply is required. The KIN D 2.0 uses an embedded Relay with 2.0 amp rating.
   This is the maximum current that can be switched reliably when connected to a ‘NON-Inductive load’ up to 30VDC. Electric strikes and magnetic locks are considered ‘Inductive Loads’. For Inductive Loads operating on DC, it is important to have the provided diode attached at the locking device to remove the CEMF pulse that is generated when switching an ‘Inductive Load’ (see DC ELECTRIC STRIKE WIRING EXAMPLE below). For Inductive Loads operating on AC, a MOV must be used -not provided-.
   An external relay should be used on larger voltage and current requirements.
   Use the provided 5 wire caps for wire connections. ALWAYS terminate any KIN D 2.0 unused wire with a wire cap.

2. KIN D 2.0 Placement
   1- Place the KIN D 2.0 in a plastic enclosure or within the wall or door frame.
   2- Place the KIN D 2.0 in a dry place with normal ambient temperatures.
   To avoid any attenuation and for proper operation DO NOT place the KIN D 2.0 behind electrical equipment such as card reader, screens, etc…
   DO NOT place the KIN D 2.0 behind metallic obstacles or behind UV coated glass or reflective glass.
   3. Once the KIN D 2.0 is placed, ALWAYS test its operational range.
   When issuing a command, the KINDOO application will inform you if the KIN D 2.0 signal is weak and the application will not emit the command. Always verify that the range within which the KINDOO application allows you to issue the command is an acceptable operational range for your installation. If not, kindly change the KIN D 2.0 placement in a way that reduces obstacles between the KIN D 2.0 and the phone of the users.
   For installations where the KIN D 2.0 is hidden, you may use the provided PIN and double sided tape to affix the PIN in a visible location at the same level of the KIN D 2.0. The PIN is simply a visual marker that helps users know where the KIN D 2.0 is located and does not serve any other function.

3. Wires Color Coding
   Green and yellow wires should be connected to a 12V to 24V DC or AC power supply
   The Red wire is the Common (C) (typically 12V to 24V DC or AC)
   The White wire is the Normally Open (NO)
   The Black wire is the Normally Closed (NC)

4. DC Electric strike wiring example

5. Riser Diagram

6. Setup
   Use the KINDOO MOBILE application to create your type D site and start setting up KIN D 2.0 devices.

End User Acknowledgement

When using KINDOO and any related hardware or software, you fully agree to all the terms and conditions of the KINDOO GENERAL TERMS AND CONDITIONS defined on our website: www.kindoo.tech/generaltermsandconditions.html
If you do not agree with any of the terms and conditions, please return the product in its original unused condition.

CE Compliance Statement

This device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Directive 2014/53/EU
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Industry Canada Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

FCC ID: 2A7TP-KIND20
IC ID: 28769-KIND20

KINDOO is a product of KINDOO LLP
7-2070 Harvey Avenue 163, Kelowna, VlY 8P8, Canada
www.kindoo.tech
June 2022
Made in China

Documents / Resources

| kindoo KIN D 2.0 DC or AC Power Supply [pdf] Installation Guide
KIN D 2.0 DC or AC Power Supply, KIN D 2.0, DC or AC Power Supply, Power Supply, Supply
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>