Dongguan Yihong Hardware Electronics YH-RF17 RF Wireless Remote Instructions

Dongguan Yihong Hardware Electronics YH-RF17 RF Wireless Remote

Functions

• 1. Turn On/Standby
  Press this key to turn on unit or switch to standby mode. At power on, unit will automaticly turn on and restore to previous status.

• 2/9. Dynamic Mode Adjust
  Switch to dynamic mode from static color, or switch between dynamic modees.

• 3/10. Dynamic Speed Adjust
  Adjust dynamic playing speed. Press SPEED+ to increase speed and press SPEED- to decrease. Unit will switch to dynamic mode If press this key at static color mode.

• 4/5. Static Color Adjust
  Switch to static color mode from dynamic mode, or switch between static colors.

• 6. Direct Color Select
  Shortcut key to static colors. When press the specific color key, LED will play the same static color. The direct colors are included in ‘COLOR+’ and “COLOR-‘operation.

• 7/8. Brightness Adjust
  Adjust static color brightness. Press BRIGHT+ to increase brightness and press BRIGHT- to decrease. Unit will switch to static color mode If press this key at dynamic mode.

• 11. Demo Mode
  Press this key will switch to Demo mode. At demo mode, it plays 17 dynamic modes in loop, each mode repeat 3 times.

Installing

1. Power Supply
   This unit accepts DC 5V to 24V power supply. The DCjack’s inner pole (or red cable) is positive and sleeve (or black cable) is negative. Also please make sure the power supply voltage ism same as the LED load.

2. LED Output
   This unit supports common anode connection LED products.
   The mark ‘ indicates the common connection node.

The peak output current is 4 amperes and the maximum constant current is 2 amperes per channel. Please reduce load if main unit is overheating.
CAUTION! Do not short-circuit or overload the LED outputs, this may lead to permanent damage!

Operation

Using Remote Controller
Please pull out the battery insulate tape before using. The RF wireless remote signal can pass through barrier, so it’s not necessary to aim at the main unit when operate.

Pairing New Remote
The remote and main unit is 1 to 1 paired as default. Furthermore, the main unit can be paired to 3 remote controllers and each renmote controller can be paired to any main unit.

Please do the following steps to pair new remote controller

1. Plug off the power of the main unit and plug it in after 5 seconds.
2. Press the’ COLOR-‘ and ‘BRIGHT- ‘keys together in 5 seconds after power on.
   After this operation, the main unit will recognize the new remote controller.

Free Remote Pairing Mode

In some specific cases; the main unit may need to be paired to any remote controllers. Please do following steps for free remote pairing mode:

1. Plug off the power of main unit and plug in after S seconds.
2. Press the’ ON/OFF and ‘MODE+”key together in 5 seconds after power on.
   After this operation, the main unit will recognize any remote controller. To pair the main unit back to specific remote, please repeat the Pairing New Remote’ operation.
   For proper receiving remote signal, please do not install the
   main unit in closed metal parts.

Switch Output Color Sequence

The controller’s default output signal sequence is Common-Green-Red-Blue. If the LED application is in different cable sequence, the direct color keys will not match the LED color. In this case, user can adjust the output signal sequence with following steps:

1. Plug off the power of main unit and plug in after 5 seconds.
2. Press ‘RED’ and ‘BLUE” color key together in 5 seconds after power on.
   With this operation, the output sequence will switch between 6 possible combinations. The sequence will be memorized and it won’t change before next same operation.

Specification

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>