AUTOAQUA SATO-270D Smart ATO nano User Manual

June 3, 2024
AUTOAQUA

Smart ATO nano
Manual

Model
SATO-270D

SATO-270D Smart ATO nano

List of Parts (Can Be Purchased Separately)

Item

| Picture|

Description

---|---|---
Smart ATO nano Controller| | 1. Integrated with one dual sensor and one replaceable diaphragm pump
2. Mounting Thickness : 0.12-0.39 inch (3-10 mm)
Universal Power
Adapter| | Input : 100-240 V 50-60 Hz
Output : 12V 1A
Preer| | A cleanable connector to remove particles in the reservoir
Anti-Siphon Valve| | 1. A valve to stop the forward siphon pressure up to  2 feet (60 cm) of water.
2. Adding one more valve (optional) can stop a  higher forward siphon pressure.
Tubing 6.5 feet (200 cm)| | Used with Diaphragm Pump,
Preer and Anti-Siphon Valve.

Caution:Risk of Injury from Strong Magnets

Smart ATO nano Controller

AUTOAQUA SATO 270D Smart ATO nano - Picture5

  1. Holes for Fixing Water Inlet Tube
  2. Power Jack
  3. Water Inlet
  4. Water Outlet
  5. Holder
  6. Hole for Fixing Water Outlet Tube
  7. Failsafe Sensor
  8. ATO Level Sensor

Prefilter

AUTOAQUA SATO 270D Smart ATO nano - Picture6

Specifications

  1. Power Input : 100-240 V 50-60 Hz

  2. Diaphragm Pump
    Suction Head : 6.5 feet (200 cm)
    Flow Rate : 7.9 gph (30 lph)

  3. Tubing I.D. : 5/32 inch (4 mm)
    O.D. : 1/4 inch (6.4 mm)

  4. Mounting Thickness
    Sensor : Max.1/2 inch (12.7 mm)
    Holder : 0.12-0.39 inch (3-10 mm)

  5. Anti-Siphon Pressure : 2 feet (60 cm) of water

Installation

  1. Take off the cover of Smart ATO nano controller and tank/sump with the holder.
  2. Mount the sensor with the magnet at the normal water level (with the water level reaching the lower one)* . If the cable is too long,  push it back into the main body.
  3.  Cut the tube to a proper length. Connect the water inlet tube withb the Preer and put it in the water.
  4. Connect water outlet tube and insert it into the holder.
  5. Connect the white part of the Anti-Siphon Valve to the end of the tube and keep it out of water.
  6. Put the cover back on Smart ATO nano controller and with the hole on the side of the cover.
  7. Connect power and do one-time o check there is no water dripping (forward siphon) after the pump stops.
  8. Unplug and plug the power adapter back in for reset.
    *Please set the sensor away from the water outlet to avoid bubble interference.

AUTOAQUA SATO 270D Smart ATO nano - Picture7

LED Indicator

LED Color Status Description Action
Alternating  &  Blue  Red LED Flashing Boot-up N.A.
Blue   LED Solid Power on N.A
lashing Reumping N.A
Flashing quickly for a short time** The fail-safe sensor senses the water
level changes. N.A
* Red   LED Flashing QST alarm :

1. Bubble interference
2. Empty reservoir| 1. Clean the sensor or move it to an  area away from micro bubbles.
2. Reeservoir.

*Please follow the instruction above to power and plug it back in.
**For very small aquariums, the top sensor may be triggered after each top off. This is normal and no action is required.

Quick Security Technology (QST)

Smart ATO nano uses QST for real-time protection against any failure situation. The controller will give a visual alert when it senses any other re. * QST can detect the  malfuction of the sensor or the pump, and the empty reservoir to avoid the pump running dry. For example, if the ., it will alert when any other rever 60 sec.
*No security time control for the .

Notice

  1. Please read the manual before installation. Keep the power adapter dry and avoid any contact with water to prevent malfunctions.
  2. Make sure the water ws through the tubing smoothly .
  3. Please open and clean the preer every 3 to 6 months for best er performance.
  4. Please visit AUTOAQUA’s website to know how to replace the pump.

Limited Warranty

  1.  Limited warranty is provided by AUTOAQUA only if your AUTOAQUA Product (“Product”) was purchased from an authorized distributor or an authorized reseller.
  2. All warranty repairs or replacement are performed by the authorized distributor or authorized reseller in the region where the Product was shipped by AUTOAQUA.
  3.  The limited warranty is valid for a period of 1 year under proper installation and normal use from the date of the original purchase listed on the proof of purchase or  sales receipt.
  4. In the event of a limited warranty claim, proof of purchase or sales receipt (issued to the original purchaser) is required.

Purchase Date (Y/M/D)
Place of Purchase
(Store name, phone, email, address)
Warranty Period
One year from the purchase date

Service
AUTOAQUA Technologies Co., Ltd.
7F-7.,NO.229,Fuxing 2nd Rd.,Zhubei City, Hsinchu County,Taiwan
E-mail : service@autoaqua.com.tw
www.autoaqua.com.tw

  • Please go to AUTOAQUA website to get the distributor information.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals