NIE-TECH RF924-TX Remote Control Switch User Manual
- June 3, 2024
- Nie Tech
Table of Contents
NIE-TECH RF924-TX Remote Control Switch
Specifications
- Battery: CR2032*2
- Frequency: 433.92MHz
- Temperature Range: 32°F~104°F
- Indoor use in dry location
OVERVIEW
- 1. Please read the online guides at support Minosto.com/Z-wave remote carefully.
- Do not use it in locations with direct water contact.
- Contains small parts keep away from children.
Power the device
- Use by hand open the remote cap,and push it to separate the 2 halves.
- Remove battery tabs.
- Your Z-wave remove Immediately should flash LED to indicate it is powered.
Inclusion/Exclusion Function
To add the device
- Follow the instructions for yOur Z-Wave certified controller to add device from the Z-Wave network.
- Once the controller is preparing to add your device, press the FIRST BUTTON(ONLY) 5 times, LED is flashing in blue during inclusion and LED stays on green for 2 seconds after inclusion successfully. If LED flashing purple for 3 seconds, please reset the device. LED will stay on red for 2 seconds after inclusion failed.
To remove the device
- Follow the instructions for your 2-Wave certified controller to remove a device from the Z-Wave network.
- Once the contractor is preparing to remove your device, press the SECOND BUTTON (ONLY) 5 times, LED is trashing in purple during exclusion and the LED stays on green for 2 seconds after exclusion successfully. LED will stay red for 2 seconds after exclusion failed.
Wake up the Device
Press the THIRD BUTTON 5 times quickly, LED wil stay solid on blue when awake
and will turn off when device goes back to sleep mode.
Factory reset
Manual: Reset: Press the FOUR BUTTON 5x, then press it 5x again when the red
light is flashing.
FCC warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: () This device may not cause harmful
interference,
(2) This device must accept any interference received, including interference
that may cause undesired operation. changes or modifications not expressly
approved by the party responsible for
Compliance could void the users authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, If not installed and used in accordance with the
instructions,may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an Outlet on a circuit different from that to which the receiver is receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance 20 cm between the radiator& your body.
CAUTION – PLEASE READ!
This device is intended for installation in accordance with the National Electric Code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada.
If you are unsure or uncomfortable about performing this installation consult a qualified electrician.
MEDICAL EQUIPMENT
Please DO NOT use this plug to control Medical or Life Support equipment. This
device should never be used to control the On/Off status of Medical and/or
Life Support equipment.
OTHER WARNINGS
Risk of Fire / Risk of Electrical Shock / Risk of Burns
IMPORTANT SAFETY INSTRUCTIONS
- READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
- Read and follow all instructions that are on the product or provided with the product.
- do not use an extension cord.
- Reterence the National Electrical Code, NFPA 70, specifically for the installation of wiring Cindclearances Trom pOwer and light conductors.
- Installation work and electrical Wiring must be done by a qualified person(s) in accordance with allapplicable codes and standards, including fire-rated construction.
- do not install or use within 10 feet of a pool
- do not use in a bathroom
WARNING:
Risk of Electric Shock.
When used outdoors, install only to a covered Class A GFCI-protected
receptacle that is weatherproof with the power unit connected to the
receptacle. If one is not provided, contact a qualified electrician for proper
installation. Ensure that the power unit and cord do not interfere with
completely closing the receptacle cover.
- Risk of Electric Shock. Mount the unit at a height greater than 1 foot from the ground surface.
- Risk of Electric fire. install only to a receptacle protected by 20A branch circuit over current protection.
This manual contains important safety and operating instructions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>