hama 00200006 USB Type-C 65W Charger Instruction Manual
- June 3, 2024
- Hama
Table of Contents
hama 00200006 USB Type-C 65W Charger
Operating instruction
Explanation of warning symbols and notes
This symbol indicates a risk of electric shock from touching product parts
carrying hazardous voltage. This symbol is used to indicate safety
instructions or to draw your attention to specific hazards and risks. This
symbol is used to indicate additional information or important notes.
Package contents
- Universal USB-C notebook power
- supply unit
- Net cable
- These operating instructions
Safety instructions
- Use the product only for the intended purpose.
- Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
- Ensure there is sufficient scope for heat dissipation and ventilation.
- Only use the article under moderate climatic conditions.
- Do not use the product in areas in which electronic products are not permitted.
- Do not use the product in a damp environment and avoid splashing water.
- Do not short-circuit the battery of the opened terminal device. There is a risk of explosion.
- Protect the product from dirt, moisture and overheating and use it in dry environments only.
- Do not drop the product and do not expose it to any major shocks.
- Do not operate the product outside the power limits specified in the technical data.
- Always pull directly on the plug when disconnecting the cable, never on the cable itself.
- Make sure that cables do not pose a tripping hazard or block emergency exits.
- Do not bend or crush the cable.
- As with all electrical products, this device should be kept out of the reach of children.
- Do not modify the device in any way. Doing so voids the warranty.
- Keep the packaging material out of the reach of children due to the risk of suffocation.
- Dispose of packaging material immediately in accordance with the locally applicable regulations.
- Make sure that the connected device meets the requirements for supply through class PS3 power sources.
- If there is any doubt, ask your device manufacturer.
Risk of electric shock
- Do not open the device or continue to operate it if it becomes damaged.
- Do not use the product if the AC adapter, adapter cable or power cable is damaged.
- Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
- The power supply unit is suitable for mains voltages of 100 – 240 V and therefore can be used worldwide.
- Please note that a country-specific adapter may be necessary.
- Ensure that your notebook requires a supply voltage of 5 V / 9 V / 12 V / 15 V / 20 V (+/- 1 Volt).
- You can find this information on the original power supply unit or in your terminal device’s operating manual.
- If necessary, ask the dealer who supplied your terminal device or contact your terminal device manufacturer’s support service.
Warning
- Do not use the universal notebook power supply unit if you are unable to definitively determine your terminal device’s supply voltage.
- Ensure that the notebook’s total power consumption does not exceed the power supply unit’s rated output of 65 W.
- Failure to comply with this may cause damage to the universal notebook power supply unit and the connected terminal device!
- Note the instructions in your device’s operating manual. If these do not contain any instructions expressly to the contrary, proceed as follows:
- Note – Power Delivery
- Plug & GO: no additional software is required, simply plug in and start:
- Thanks to Power Delivery/Thunderbolt™ 3/Quick Charge, the voltage and power are adjusted automatically.
- Be aware that, for efficient and optimized charging, your terminal device must support the PD (Power Delivery)/TBT3 (Thunderbolt™ 3)/QC (Quick Charge) function.
- If you have a large number of PD/TBT3/QC-enabled terminal devices with different firmware updates, it may be that the function is not fully supported.
Warning
- Only operate the product from a socket that has been approved for the device. The socket must be installed close to the product and must be easily accessible. Disconnect the product from the power supply using the On/Off switch – if this is not available, unplug the power cord from the socket.
- If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
- Connect the power cord to the power supply unit and your terminal device.
- Then connect the mains plug to a properly installed socket.
- The terminal device can now be used and switched on /charged.
Care and Maintenance
Disconnect the product from the mains before cleaning.
- Only clean this product with a slightly damp, lint-free cloth, and do not use aggressive cleaning agents.
- Ensure that no water is able to enter the product.
Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage
resulting from improper installation/mounting, improper use of the product or
failure to observe the operating instructions and/or safety notes.
Technical data
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>