Montezuma MKDB30B 30 Inch Steel Utility Box Owner’s Manual
- June 3, 2024
- Montezuma
Table of Contents
Montezuma MKDB30B 30 Inch Steel Utility Box
LIFE ORGANIZED
Montezuma is committed to helping you succeed in both your work and personal life by being organized, prepared and equipped with the right tools, gear and home supplies at your finger tips. Keep your life organized with Montezuma. Thank you for your purchase of this Montezuma Utility Box
ATTENTION
TO REDUCE THE RISK OF INJURY, THE USER MUST READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE USING THIS PRODUCT FOR THE FIRST TIME. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fill in the following information and retain this owner’s manual for future reference:
SPECIFICATIONS
30″ STEEL UTILITY BOX MKDB30B OVERALL DIMENSIONS: 30″ W x 12-5/8″ D x 8-7/8″ H (76.2 cm W x 32 cm D x 22.4 cm H) 36″ STEEL UTILITY BOX MKDB36B OVERALL DIMENSIONS: 36″ W x 14-1/4″ D x 10-5/8″ H (91.4 cm W x 36.1 cm D x 26.9 cm H) 42″ STEEL UTILITY BOX MKDB42B OVERALL DIMENSIONS: 42″ W x 15-3/4″ D x 12-3/8″ H (106.7 cm W x 40 cm D x 31.4 cm H) 47″ STEEL UTILITY BOX MKDB47B OVERALL DIMENSIONS: 47-1/4″ W x 17-1/4″ D x 14-1/4″ H (120.1 cm W x 43.8 cm D x 36.2 cm H)
- Height does not include feet.
PART NUMBER QTY
| REF | DESCRIPTION | PART NUMBER | QTY |
|---|---|---|---|
| 1 | SIDE HANDLE ASSEMBLY | 122371 | 2 |
| 1 x Side Handle | |||
| 4 x M6 Flange Nut | |||
| 4 x M6 x 12 Hex Bolt | |||
| 2 | LOCK ASSEMBLY | 122372 | 1 |
| 1 x Lock Body | |||
| 1 x M18 Hex Nut | |||
| 1 x Locking Cam | |||
| 1 x M5 x 6 Screw | |||
| 3 | M8 Flange Nut | 122373 | 8 |
| 4 | Rubber Gasket | 122374 | 8 |
| 5 | Metal Washer | 122375 | 8 |
| 6 | M8 x 16 Hex Bolt | 122376 | 8 |
| 7 | WATER RESISTANT SEAL | 1 | |
| For 30″ Utility Box | 122377 | ||
| For 30″ Utility Box | 122380 | ||
| For 42″ Utility Box | 122381 | ||
| For 47″ Utility Box | 122382 | ||
| 8 | LID STOP | 1 | |
| For 30″ Utility Box | 122378 | ||
| For 36″ Utility Box | 122383 | ||
| For 42″ Utility Box | 122384 | ||
| For 47″ Utility Box | 122385 |
To order replacement parts, email service@montezumastorage.com or call 1-800-459-4409 (MondayFriday, 8:00 am4:30 pm, CST). Have the part number and quantity ready. Replacement keys may be ordered using the code that appears on the face of the lock. Not all parts are covered under warranty. Those parts not covered can be purchased.
2|
Side Handle Assembly
Includes side handle and hardware for installing (4 x M6 Flange Nut and 4 x M6
x 12 Hex Bolt)
---|---
1|
Lock Assembly
Includes lock body and hardware for installing (1 x M18 Hex Nut, 1 x Locking
Cam and 1 x M5 x 6 Screw)
8|
M8 Flange Nut
For attaching the feet
8|
Metal Washer
For attaching the feet
8|
Rubber Gasket
For attaching the feet
8|
M8 x 16 Hex Bolt
For attaching the feet
1|
Water Resistant Seal
For sealing the lid (pre-installed)
1|
Lid Stop
For securing the lid (pre-installed)
ASSEMBLY
Place the bottom panel with the edges facing up, as shown below.
Insert the squares tabs on the right side panel into the corresponding holes
in the back panel. Then, insert the half moon tabs in the front and right side
panels into the corresponding holes in the bottom panel. See illustration
below. Tip: It may be helpful to use a rubber mallet to gently secure the tabs
into the holes.
ATTENTION: Make sure the tabs are completely inserted in the holes to
prevent them from coming apart when box is loaded.
Repeat to attach the front and left side panels.
Place the lid on the assembled body and press down to attach it to all four of
the body panels. Gently tap the half moon tabs with a rubber mallet until they
are fully engaged.
ATTENTION: Make sure the tabs are completely inserted in the holes to
prevent them from coming apart when box is loaded.
Attach each side handle using four (4) M6 x 12 hex bolts and M6 flange nuts.
To assemble the lock, place the lock body in the opening on the front of the
utility box. Thread the M18 hex nut onto the lock body, and tighten until the
lock is secured against the front of the utility box. Slip-joint pliers can
help tighten the nut into place. Place the locking cam onto the lock body and
secure with the M5 x 6 screw. Tighten the screw to secure the lock assembly in
place, but not so tight that you cannot turn the locking cam with the key.
NOTE: You may need two people to to complete this step with larger utility boxes. Lay the box on its back with the lid open. Line up the steel feet with the holes in the bottom panel. Insert the M8 x 16 hex bolts through the metal washers, the bottom inside of the utility box and then through the steel feet on the other side of the panel. Secure using the rubber gaskets and M8 flange nuts.
MAINTENANCE
Regularly check the swing-up side handles to make sure they are secure.
SAFETY
CAUTION
Make sure the weight of the contents is distributed evenly.
30″ UTILITY BOX: The maximum product weight, including contents, is 150
lb (68 kg).
36″ UTILITY BOX: The maximum product weight, including contents, is 300
lb (136 kg).
42″ UTILITY BOX: The maximum product weight, including contents, is 450
lb (204 kg).
47″ UTILITY BOX: The maximum product weight, including contents, is 600
lb (272 kg).
This product is warranted to be free from defects in materials and workmanship
for a period of one (1) year from the date of original purchase.
If this product is defective, email service@montezumastorage.com
or call
1-800-459-4409 (Monday–Friday, 8:00
am–4:30 pm, CST). If the product is defective, we will replace the defective
part at no cost to you.
Please do not ship your product back to the store or to us unless we send you
written instructions for return.
In the event it becomes necessary for your product to be returned, we will
notify you how to proceed.
A copy of your original purchase receipt must accompany the returned product.
Manufactured by:
QUALITY CRAFT
Romeoville, IL 60446
service@montezumastorage.com
1-800-459-4409
(Monday to Friday, 8:00 am–4:30 pm, CST)
Made in China
www.montezumastorage.com
FORM#: MKDB-04/20
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>