Montezuma MPSO-4B 4-BAY POWER TOOL ORGANIZER Owner’s Manual
- June 5, 2024
- Montezuma
Table of Contents
Montezuma MPSO-4B 4-BAY POWER TOOL ORGANIZER
LIFE ORGANIZED
Montezuma is committed to helping you succeed in both your work and personal
life by being organized, prepared and equipped with the right tools, gear and
home supplies at your finger tips.
Keep your life organized with Montezuma.
Thank you for your purchase of this Montezuma Power Tool Organizer.
ATTENTION
TO REDUCE THE RISK OF INJURY, THE USER MUST READ AND UNDERSTAND THIS
INSTRUCTION MANUAL BEFORE USING THIS PRODUCT FOR THE FIRST TIME. SAVE THESE
INSTRUCTIONS FOR FUTURE REFERENCE.
Fill in the following information and retain this owner’s manual for future
reference:
MODEL(S):
DATE OF PURCHASE:
PLACE OF PURCHASE:
RECEIPT NO:
SPECIFICATIONS
- MAXIMUM WEIGHT FOR POWER TOOL BAYS: 5 lb (2.3 kg)
- MAXIMUM WEIGHT FOR TOP AND MIDDLE SHELVES: 20 lb (9.1 kg)
PARTS LIST
| REF | DESCRIPTION | PART NUMBER | QTY |
|---|---|---|---|
| 1 | Nut | 122260 | 15 |
| 2 | Bolt | 122261 | 15 |
| 3 | Self Tapping Screw | 122262 | 4 |
| 4 | Plastic Drywall Anchor | 122263 | 4 |
To order replacement parts, email
[email protected] or call
1-800-459-4409 (Monday–Friday, 8:00
am–4:30 pm, CST). Have the part number and quantity ready.
Not all parts are covered under warranty. Those parts not covered can be
purchased.
TOOLS REQUIRED
- Phillips head screwdriver
- Socket wrench
- Power drill
- Level
ASSEMBLY
Attach the two side panels to the bottom panel using two bolts and nuts per
side.
Note: the tabs on the front of the power tool slots should face down.
Attach the two side panels to the middle shelf using two bolts and nuts per
side.
Note: the holes in the edge of the shelf should face forward.
Attach the two side panels to the top shelf using two bolts and nuts per side.
Note: the flange on the top shelf should face downward.
Position the support bar so the slot passes through the tab on the bottom
shelf with the power tool slots. Secure the bar by lining up the hole at the
top of the support bar with the corresponding hole on the middle shelf. The
support bar should be positioned behind the front edge of the middle shelf.
Secure using a bolt and nut.
INSTALLATION
This organizer is built for 16″ on center wall studs. Locate the wall studs
and mark the locations of the four holes shown in the illustration. Use a
level to make sure the organizer is straight.
Pre-drill pilot holes into the wall studs. Secure the self-tapping screws into
the marked locations, leaving enough room to position the organizer in place
using the keyhole slots.
Then tighten down the screws to secure the organizer in place.
Note: To secure into dry wall, use the plastic drywall anchors. For safety and security, the organizer should be mounted into at least one stud wall.
WARRANTY
This product is warranted to be free from defects in materials and workmanship
for a period of one (1) year from the date of original purchase.
If this product is defective, email [email protected]
or call 1-800-459-4409 (Monday–Friday,
8:00 am–4:30 pm, CST). If the product is defective, we will replace the
defective part at no cost to you. Please do not ship your product back to the
store or to us unless we send you written instructions for return.
In the event it becomes necessary for your product to be returned, we will
notify you how to proceed.
A copy of your original purchase receipt must accompany the returned product.
Manufactured by:
QUALITY CRAFT
Romeoville, IL 60446
[email protected]
1-800-459-4409
(Monday to Friday, 8:00 am–4:30 pm, CST)
Made in China
www.montezumastorage.com