PiPat W00 Smart Bracelet User Manual

PiPat W00 Smart Bracelet User Manual

Assemble and wear the bracelet

1. Take out the bracelet body and wristband:
2. Put the bracelet body into the wristband:
3. Put the wristband on your wrist.

Note: it is best to wear the bracelet behind the sty\aid process of ulna. Adjust the size of the bracelet to suit the wrist according to the adjusting hole. The sensor should be close to the skin to avoid movement.

Install app on mobile phone

Search for “pitpat” in the app store or scan the following QR code to download and install the app.

System requirements: ios13 or above;Android 6.0 or above.

Bind the bracelet to the treadmill

1. Bracelet boot
   Long press the bracelet button, and the bracelet vibrates once to display the pitpat interface;

2. Turn on the treadmill, put the screen of the bracelet on the NFC logo of the tread mill, the treadmill make a sound of “bleep”, and the bracelet is connected with the treadmill.
   Once the bracelet is successfully bound, it will recording your running information immediately.

Note: The initial connection between the bracelet and the treadmill requires touching the NFC logo of the treadmill. After the first connection, the next time you start the bracelet, it will automatically connect to the treadmill.

Start using

Bracelet startup: in the shutdown state, long press the button, and the bracelet will vibrate then the pitpat interface will be displayed, and the bracelet wiII be powered on;
Bracelet shutdown: long press the bracelet button, the bracelet will vibrate then the bye interface will be displayed, and the bracelet will be shutdown.

1. standby mode:

When the bracelet is not connected to the treadmill or the treadmill is in standby mode lthe treadmill stops moving], the bracelet automatically enters the standby mode. The bracelet displays the power of the bracelet in standby mode.

Motion mode:

When the treadmill enters the running state, the bracelet will automatically enter the sports mode,

1. At this time, the main interface of the bracelet displays the heart rate, steps and movement information. |in the exercise mode, the bracelet will automatically detect the heart rate, and the heart rate detection light flashes.
2. The bracelet displays the power and Bluetooth connection status.
3. Touch the display screen and the screen will be lit when the hand is in the state of resting screen.
4. For other Bracelet click, double click and three click operations, please refer to the instructions of pitpat app

Bracelet charging

Note: flake sure the bracelet is in normal power for the first time use. If it cannot be started normally in low power, please connect the charger to charge the equipment, and the bracelet will start automatically.

Insert the charging head of the bracelet body into the female head of the power cord.

Product parameters

• Product model: WOO
• Battery type: lithium polymer battery
• Battery capacity: 90mah
• Connection method: Bluetooth 5.0
• Wristband material: Rubber
• Equipment requirements: system requirements ios13 or Android 6.0 above
• Screen size: 0.96 inch

WARNING

1. Please do not wear bracelets when bathing and swimming.
2. Do not expose the bracelet to high moisture, high temperature or low temperature for a long time.

FCC Regutations

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesiredoperation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with FCC RF Exposure compliance requirements, this grant is applicable to only Mobile Configurations.
Transmitter Power – 2DBM, SAR Exemption Test.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>