idataSTaRT 2017 HYUNDAI Elantra STD Key Automatic Installation Guide

: June 3, 2024
: idataSTarT

Table of Contents

2017 HYUNDAI Elantra STD Key Automatic
T-HARNESS / COMPONENT LOCATOR
T-HARNESS / WIRING DIAGRAM
HARDWIRE / COMPONENT LOCATOR
HARDWIRE / WIRING DIAGRAM
MODULE PROGRAMMING PROCEDURE
TAKEOVER PROCEDURE – STD KEY
INSTALLATION CHECKLIST
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

INSTALL GUIDE
2017 HYUNDAI ELANTRA STD KEY AUTOMATIC

2017 HYUNDAI Elantra STD Key Automatic

DOCUMENT NUMBER
A44DC0C

REVISION DATE
20210923_071130

FIRMWARE
RSA-HK5

HARDWARE
CMHCXA0

ACCESSORIES
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.

TERMS OF USE
Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, noncompliant Certified Technicians or end users.

T-HARNESS / COMPONENT LOCATOR

T-HARNESS / WIRING DIAGRAM

HARDWIRE / COMPONENT LOCATOR

HARDWIRE / WIRING DIAGRAM

MODULE PROGRAMMING PROCEDURE

| Turn key to ON position.| | Press and hold the brake pedal.
---|---|---|---
| Wait, if LED 1 turns solid GREEN, proceed with step 4. If LED 1 ﬂashes RED three times [3x], proceed with step 3.| | Press and release the module’s programming
button.
| The vehicle’s immobilizer is NOT detected: For USDM vehicles without an immobilizer, press and release the odule’s programming button. Wait until LED 1 turns solid GREEN then proceed with step 4. For DM and USDM vehicles with an immobilizer, verify every wire connections and repeat the module programming procedure.| | Release the brake pedal.
| Turn key to OFF position.| | Wait, LED 2 will ﬂash GREEN.
| START vehicle for 15 seconds.| | Module Programming Procedure completed.

TAKEOVER PROCEDURE – STD KEY

| All vehicle doors must be closed and locked prior to remote start sequence.
---|---
| Press unlock on aftermarket remote.
| Insert key into ignition.
| Turn key to ON position.
| Press and release BRAKE pedal.
| Take over procedure completed.
| Failure to follow procedure will result in vehicle engine shutdown.

INSTALLATION CHECKLIST

CHECKLIST – WITH AFTERMARKET KEYFOB

WARNING: Vehicle engine will start many times. Test in a well ventilated area.
Close all vehicle doors, hood and trunk.
Press the LOCK button once [1x] on the aftermarket key fob.
Question 1: Do the doors lock?
• YES: Go to next step.
• NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
Press the UNLOCK button once [1x] on the aftermarket key fob.
Question 2: Do the doors unlock?
• YES: Go to next step.
• NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
Press the TRUNK release button once [1x] on the aftermarket key fob if supported.
Question 3: Does the trunk or hatch open/unlock?
• YES: Close trunk or hatch and go to next step.
• NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
Press the AUX 1 button once [1x] on the aftermarket key fob if supported.
Question 4: Does the driver side sliding door open?
• YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
• NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
Press the AUX 2 button once [1x] on the aftermarket key fob if supported.
Question 5: Does the passenger side sliding door open?
• YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
• NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
Press the START/STOP button once [1x] on the aftermarket key fob to remote start vehicle.
Question 6: Does the vehicle remote start?
• YES: Go to next step.
• NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
• YES: Go to next step.
• NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
• YES: Go to next step.
• NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
Open hood.
If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
Press the START/STOP button once [1x] on the aftermarket key fob to remote start vehicle.
Question 9: Does the vehicle remote start?
• YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
• NO: Go to next step.
Close hood.
Enter vehicle and close the doors.
Press the START/STOP button once [1x] on the aftermarket key fob to remote start vehicle.
Wait for the vehicle to start.
Press brake pedal.
Question 10: Does the vehicle shut down?
• YES: Go to next step.
• NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket key fob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
Exit vehicle.
Installation checklist completed.

CHECKLIST – WITH OEM KEYFOB

WARNING: Vehicle engine will start many times. Test in a well ventilated area.
Close all vehicle doors, hood and trunk.
Press LOCK button three times [3x] rapidly on the OEM key fob to remote start vehicle.
Question 1: Does the vehicle remote start?
• YES: Go to next step.
• NO: The module doesn’t detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
Press LOCK button three times [3x] rapidly on the OEM key fob to shut down vehicle.
Question 2: Does the vehicle shut down?
• YES: Go to next step.
• NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
• YES: Go to next step.
• NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
Open hood.
If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
Press LOCK button three times [3x] rapidly on the OEM key fob to remote start vehicle.
Question 4: Does the vehicle remote start?
• YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
• NO: Go to next step.
Close hood.
Enter vehicle and close the doors.
Press LOCK button three times [3x] rapidly on the OEM key fob to remote start vehicle.
Wait for the vehicle to start.
Press brake pedal.
Question 5: Does the vehicle shut down?
• YES: Go to next step.
• NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM key fob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
Exit vehicle.
Installation checklist completed.

U.S. Patent No. 8,856,780 CA 2759622
Automotive Data Solutions Inc. © 2021
RSA-HK5-[CMHCXA0]-EN
2017 Hyundai Elantra STD key Automatic
www.idatalink.com