Trimco UHF212 Hands Free Slide Lock Installation Guide

Trimco UHF212 Hands Free Slide Lock

ABOUT COMPANY

• TRIANGLE BRASS MANUFACTURING
• 1351 ROCKY POINT DRIVE
• OCEANSIDE, CA 92056
• WWW.TRIMCOHARDWARE.COM
• CSR@TRIMCOHARDWARE.COM
• 323.262.4191

PARTS LIST

NOT TO SCALE. IF ANY PARTS ARE MISSING, PLEASE CONTACT TRIMCO CUSTOMER SERVICE.

BOX 1 ITEMS

• (A) 1X INTERIOR ASSEMBLY
• (B) 1X EXTERIOR PULL
• (C) 1X EXTERIOR MACHINE SCREWS, 10-24 X 3/4
• (D) iX CARRIER
• (E) 1X LOCKING BOLT
• (F) 1X LATCH FACE AND SCREWS
• (G) 1X DOOR STRIKE AND SCREWS
• (H) 16X INTERIOR AND EXTERIOR PLATE WOOD/SHEETMETAL SCREWS
• (I) 1X INDICATOR WITH OPEN & CLOSE STICKERS
• (J) 1X INTERIOR OPEN AND CLOSE STICKERS
• (K) 1X EMERGENCY OPEN TOOL
• (L) 1X HH SIGN STICKER (FOR HEALTHY HARDWARE ONLY)
• (M) 1X HANDS FREE STICKER

PARTS

TOOLS

TOOLS BELOW MAY BE REQUIRED. TOOLS NOT INCLUDED.

• CROSSHEAD SCREW DRIVER
• PILOT HOLE DRILL (SIZE 3/32)

OVERVIEW

UHF 212 (OUTSWING VERSION)
HANDS FREE SLIDE LOCK INSTALLATION GUIDE
FOLLOW THE INSTRUCTIONS BELOW FOR STEP BY STEP INSTALLATION. SCAN QR CODE FOR INSTALLATION VIDEO. FOR INSTALLATION HELP, PLEASE CONTACT TRIMCO CUSTOMER SERVICE.

INSTALLATION INSTRUCTION

• STEP 1: REMOVE ALL EXISTING DOOR HARDWARE INCLUDING THE DEADBOLT IF NEEDED.
  PRO TIP:

  • NEW INSTALLATIONS FOLLOW ANSI 161 CYLINDRICAL DOOR PREPERATION.

  • RETROFIT COMPATIBILITY TO ANSI 161 CYLINDRICAL DOOR PREPERATION.
    NOTE: ONLY COMPATIBLE WITH 1-3/4″ THICK DOORS.

  • INTERIOR SIDE:
    INSERT CARRIER AS SHOWN. INSERT BOLT INTO CARRIER
    NOTE: HOLES INDICATE

  • FOR 2 3/4 OR 2 3/8 DOOR WIDTH SEE STEP 2

• STEP 2: INSTALL INTERIOR INDICATOR DECALS: ADHESIVE IS ON THE GRAPHIC SIDE OF DECAL, AND MUST BE INSTALLED ON THE BACK OF THE INTERIOR ASSEMBLY TO BE VISIBLE THROUGH THE INDICATOR WINDOWS.
  
  
  PRO TIP:
  DEPENDING ON DOOR HANDING, CHECK TO SEE THAT THE LOCKED DECAL IS SHOWN THROUGH THE CORRECT INDICATOR WINDOW BY SLIDING THE BOLT TO THE LOCKED POSITION. IF INCORRECT, SWITCH DECALS.

• STEP 3: INSTALL INTERIOR ASSEMBLY (STUDS THROUGH CARRIER)
  

PRO TIP: USE TAPE TO HOLD ASSEMBLY IN PLACE WHILE THE EXTERIOR IS BEING INSTALLED

• **STEP 4: INSTALL INDICATOR WITH LEFT OR RIGHT DECAL, DEPENDING ON DOOR HANDING.

INSTALL EXTERIOR PULL LOOSELY TO INTERIOR ASSEMBLY STUDS. (DO NOT TIGHTEN UNTIL PLATES ARE ALIGNED TO DOOR).
PRO TIP:**
EXTEND LATCH BOLT WHEN TIGHENING OUTER PLATES TO DOOR SURFACE. THIS HELPS INSURE ALIGNMENT.

• STEP 5: USE LEVEL OR MEASURE FROM DOOR EDGE TO ALIGN INTERIOR ASSEMBLY AND EXTERIOR PULL.

• STEP 6: INSTALL EXTERIOR PULL DOOR SCREWS.

INSTALL INTERIOR ASSEMBLY MOUNTING SCREWS AND LATCH FACE.
PRO TIP:
TO INSURE PROPER FUNTION LATCH PLATE AND STRIKE MUST BE PROPERLY ALIGNED.

Always refer to WWW.TRIMCOHARDWARE.COM for the latest documentation

References

• Home - Trimco Hardware

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>