velleman DVB-T Receiver User Manual

June 3, 2024
Velleman

velleman - logo DVB-T Receiver
User Manual

velleman DVB-T Receiver

Introduction

To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as  unsorted municipal waste; it should be taken to a specialised company for recycling. This device should be returned to your distributor or to a local recycling service. Respect  the local environmental rules.
If in doubt, contact your local waste disposal authorities.

Thank you for buying the DVBTR! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, don’t install or use it and  contact your dealer. Features:

  • Connectable to any TV set (PAL / NTSC)
  • Easy connection and operation
  • Perfect digital and noise-free image and sound
  • Perfect reception with a standard antenna

Safety Instructions

Be very careful during the installation: touching live wires can cause life- threatening electroshocks.
Keep this device away from rain and moisture.

  • Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
  • Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
  • Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.
  • Do not plug or unplug the power cord when your hands are wet.
  • Keep the power cord away from heat sources. Clean the plug every now and then.
  • Switch the unit to standby mode or turn off the power when the unit is not being used. Disconnect the device from the mains to clean it. Handle the power cord by the plug only.
  • If the device emits smoke, bad smells or noises, switch off the unit and disconnect the power cord from the mains.
  • Note that damage caused by user modifications to the device is not covered by the warranty.
  • Keep the device away from children and unauthorised users.

General Guidelines

  • The DVBTR should only be used with an alternating current of max. 230VAC / 50Hz.
  • Do not attempt to disassemble the unit.
  • Select a location where the device is protected against extreme heat (see “Technical Specifications”), dust and moisture.
  • Keep the unit out of direct sunlight. Do not place the unit near heating devices or in automobiles. Avoid places with excessive dust, strong magnetic or static electricity and vibrations.
  • Keep the device away from water and other liquids. Never bring magnetic objects near the unit.
  • Place the unit in a horizontal position and avoid placing heavy objects atop of it. Do not place the device on top of amplifiers or other heat-producing equipment.
  • All modifications of the device are forbidden for safety reasons.
  • Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks, crash, etc. Using the device in an unauthorised way will void the warranty.

Description

Front Panel

velleman DVB-T Receiver - Figure 1

1. Standby button 5. Standby LED
2. Power LED 6. IR sensor
3. Lock LED 7. PROG ▼button (DOWN / CH -)
4. Digital LED display 8. PROG ▲button (UP / CH +)

Rear Panel

velleman DVB-T Receiver - Figure 2

1. Aerial connection 6. Video output
2. HDMI™ output jack 7. Left channel output connection
3. Loop out connection 8. Audio coaxial output connection
4. TV SCART connection 9. Right channel output connection
5. VCR SCART connection 10. AC power cord

NOTE: Unplug and keep the power cord orderly when the unit is idle for a long time in order to avoid electricity leakage and shock.

Remote Control

velleman DVB-T Receiver - Figure 3

1. Standby button 14. YELLOW button
2. Numerical buttons 15. BLUE button
3. TTX (Teletext) button 16. WHITE button
4. MENU button 17. GREEN button
5. ▲ button (UP / CH +) 18. MODE button
6. ◄ button (LEFT / VOL -) 19. AUDIO button
7. OK button 20. LAST button (last channel)
8. PG- button (page down) 21. PG+ button (page up)
9. ▼ button (DOWN / CH -) 22. ► button (RIGHT / VOL +)
10. TV / R button (TV / radio channel) 23. EXIT button
11. INFO button (channel information) 24. SUB button (subtitle)
12. EPG button (Electronic Program Guide) 25. MUTE button
13. RED button 26. HDMI™

Connection

  • Make sure the power switch and other equipment to be connected are turned off before connection.
  • Observe the colour coding when connecting audio and video cords.
  • Use the correct output mode when connecting the system to the TV set (including signal mode and signal code type) to avoid image distortion.
    velleman DVB-T Receiver - Figure 4
1. Aerial (optional) 6. Audio / Video cable (cable optional)
2. TV set (optional) 7. Power cord
3. DVBTR 8. VCR SCART connector (cable optional)
4. TV SCART connector (cable optional) 9. Second DVBTR (optional)
5. Digital video connector 10. VCR (optional)

Remote Control

Battery Installation

Insert the batteries respecting the polarity.
Btteries’ Service Life

  • The batteries normally last up to one year depending on frequency of usage.
  • Replace the batteries when the remote control unit fails to work. Do not mix old and new batteries.
  • Use 2 x AAA batteries. Do not use rechargeable (NiCd) batteries.
  • Do not short circuit, disassemble, heat or throw the batteries into the fire.
  • Do not drop or step onto the remote control.
  • Remove the batteries when the remote control is not being used for a long time to avoid electrolytic leakage. Wipe away any electrolyte leakage inside the remote control.  If any leaking should come into contact with parts of your body, rinse thoroughly with water.

Operation Range

  • The operation range is up to 5 meters in angle of 60° of the front of the IR sensor.
  • The operating distance may vary according to the room’s brightness.
  • Do not point bright lights at the remote control sensor.
  • Do not place objects between the remote control and the IR sensor. Do not use the remote control while simultaneously operating the remote control of any other equipment.

Installation

Connect this unit and other equipment according to fig. 4 (see “5. Connection”).

  • Switch on the device via the power switch on the front panel.
  • Press the MENU button to enter the MAIN MENU.
  • Select a submenu with/ and press OK to enter. Press / to select an option and exit the submenu by pressing ENTER.

Shortcut keys:
MUTE: press to mute/un-mute the sound.
TTX: press this button to show the teletext information (if available).
SUB: turn the subtitles on/off by pressing this button.
STANDBY: enter the standby mode, press again to return to working status.
CH+/CH- (◀/▶): press this button to enter the next or previous menu.
VOL+/VOL- (▲/▼): adjust the volume level.
OK: press to confirm.
PG+/PG-: press this button to go to the next/previous page.
TV/R: press to switch between TV channels and radio channels.
LAST: return to the last service.
INFO: press this button to show the information of the current service.
MODE: press to browse nine channels at the time.
RED, GREEN, YELLOW, BLUE: function operation.
AUDIO: press to select the audio language or audio output mode.
P-TIMER: press to set the program timer.
HDMI: press to switch between digital and normal AV output.

The Channel Menu
This window shows the channel list. Choose one the four submenus.
TV Channel List

  • Choose a channel with▲/▼.
  • Press ◀▶to select a favourite group.
  • Quit the submenu with MENU or EXIT.
  • Press numeric button 1 to edit all TV channels.
  • Press numeric button 2 to search for a particular channel.
  • Press numeric button 3 to sort the TV channels into various favourite groups.
  • Press numeric button 4 to move the TV channel to a different place.
  •  Press PG+/PG- to see the next/previous page. A maximum of 400 channels can be stored.
    velleman DVB-T Receiver - Figure 6

Radio Channel List

  • Choose a channel with▲/▼.
  • Press ◀/▶ to select a favourite group.
  • Quit the submenu with MENU or EXIT.
  • Press numeric button 1 to edit all radio channels.
  • Press numeric button 2 to search for a particular channel.
  • Press numeric button 3 to sort the TV channels into various favourite groups.
  • Press numeric button 4 to move the radio channel to a different place.
  • Press PG+/PG- to see the next/previous page. A maximum of 400 channels can be stored.

Delete All Favorites/Delete All

  • Press OK to select the submenu and to delete all the favourite TV and radio channels or all stored channels.

The Installation Menu
This window shows the installation menu. Choose one the three submenus.

Auto Scan

  • Scan Mode: scan all free or all channels (including paid channels).
  • Search: press OK to conduct an automatic scan or press EXIT to quit. The scan box displays the scan progress as well as details about the scan band, frequency,  demodulation mode, channel number, transmission mode and guard interval.

Channel Scan

  • Scan Mode: scan by channel/frequency.
  • Scan Band: select the VHF/UHF band.
  • Ch No: channels 5 ~ 12 (VHF) and channels 21 ~ 69 (UHF).
  • Frequency: frequencies 174 ~ 230MHz (VHF) and 470 ~ 862MHz (UHF) are available.
  • Band Width: select between 6MHz, 7MHz and 8MHz.
  • Search: press OK to conduct an automatic scan or press EXIT to quit. The scan box displays the scan progress as well as details about the scan band, frequency,  demodulation mode, channel number, transmission mode, guard interval, signal intensity and signal quality.
    velleman DVB-T Receiver - Figure 8

Tuner Setting

  • On/Off: enable or disable the 5V power supply for the active antenna.

The Setup Menu
This window shows the setup menu. Choose one the six submenus.
OSD Language

  • Press OK to enter the menu and choose a language: English, Croatian, Czech, Danish, Dutch, Finnish, French, German, Greek, Hungarian, Italian, Polish, Portugal,  Russian, Slovak or Spanish.
    velleman DVB-T Receiver - Figure 9

TV System

  • Display Mode: Auto, PAL, NTSC.
  • Aspect Ratio: 4:3 LB, 4:3 PS, 16:9.
  • Video Output: CVBS, RGB, HDMI™.
  • LCN Mode: On/Off. Select On to automatically list the channels in a natural order according to the stream. Select Off to list the channels in a routine order of channel numbers.velleman DVB-T Receiver - Figure 10

Region and Time

  • Region: France, Germany, Greece, Iran, Italy, Poland, Portugal, Russia, Spain, Sweden, United Kingdom, Vietnam, Argentina, Australia, Czech, Denmark and Finland.
  • GMT Usage: User Define, By Region and Off.
  • GMT Offset: Within GMT + 12:00 ~ GMT -11:30.
  • Date: Press OK to start the setup, then move the cursor with /and use the numeric buttons to modify the date. Press OK to confirm.
  • Time: Press OK to start the setup, then move the cursor with /and use the numeric buttons to modify the time. Press OK to confirm.
  • Summer Time: On/Off.
  • Time Display: On/Off.
    velleman DVB-T Receiver - Figure 11

Summer Time only available when By Region is selected; GMT Offset only available when User Define is selected

Timer Setting

  • Program Timer: Timer Number (1 ~ 8), Timer Mode (Once, Daily, Weekly, Monthly), Timer Service (TV/Radio), Wakeup Channel, Month, Date, Day, Time.
  • Sleep Timer: Off, 10 min, 30 min, 60 min, 90 min, 120 min. Press OK to confirm.
  • Remains: Displays the remaining sleep time.
    velleman DVB-T Receiver - Figure 12

OSD Setting

  • Subtitle display: On/Off.
  • OSD Transparency: 10%, 20%, 30%, 40%, 50%, 60%, 70%.
  • OSD Style: Style 1, Style2.
  • Load Default OSD Setting: Yes/No or Restore to default settings.

Parental Lockvelleman DVB-T Receiver - Figure 13

  • Enter the default password (0000) to enter the setup page.
  • Menu Lock: On/Off.
  • Channel Lock: On/Off.
  • Parental Lock: None, Age 4 ~ 18.
  • New Password: Press OK and enter your new password.
  • Confirm password: Re-enter your password and press OK to confirm.

velleman DVB-T Receiver - Figure 14

Tools
This window shows the tools menu. Choose one the three submenus.
Receiver Informationvelleman DVB-T Receiver - Figure
15

Tools
This window shows the tools menu. Choose one the three submenus.

Receiver Information

  • Move the cursor and press OK to display information about the receiver, hardware, software and remote control.

Game

  • Choose a game: Tetris®, Snake® or Othello®.

Load Factory Default

  • Press OK to load the default settings. Press Yes and OK to confirm. We recommend setting the default settings at first use.
Main Menu Submenu Options Description
TV channel list
Radio channel list
Channel Delete all favourites

Delete all
Installation| Auto scan| | Free| Scan free channels
Scan mode| All| Scan all channels
Search| |
Channel scan| Scan mode| By channel
By frequency
Scan band| VHF
UHF
Ch no| 5 —12
VHF channels|
21 — 69| UHF channels
Frequency| 174 — 230MHz| VHF frequency
470 — 862MHz| UHF frequency
Bandwidth| 6MHz|
7MHz
8MHz
Search|
Tuner setting| Tuner power| On/off| Active antenna on/off
Setup| OSD language| OSD language| English|
Croatian
Czech
Danish
Dutch
Finnish
French
German
Greek
Hungarian
Italian
Polish
Portuguese
Russian
Slovak
Spanish
TV system| Display mode| Auto
PAL
NTSC
Aspect ratio| 4:3 LB| Letterbox
4:3 PS| P-scan
16:09|
Video output| CVBS|
RGB|
HDMITI”|
LCN mode| On/off|
Region and time| Region| France|
Germany|
Greece|
| | | Iran|
---|---|---|---|---
| Italy
| Poland
| Portugal
| Russia
Spain
Sweden
United Kingdom
Argentina
Australia
Czech Republic
Denmark
Finland
GMT usage| User define
By region
Off
GMT offset| GMT+12:00—GMT-11 30
Date|
Time
Summer Time| On/off
Time display| On/off
Timer setting| Program timer| Timer number
Timer mode
Timer service
Wake up channel
Month
Date
Day
Time
Sleep timer| Off/10/30/60/90/120 min
Remains|
OSD setting| Subtitle display| On/off
OSD transparency| Off
10/20/30/40/50%
60/70%
OSD style| Style 1
Style 2
Load default OSD setting
Parental lock| Menu lock| On/off
Channel lock| On/off
Parental lock| None/age 4 — 18
New password|
Confirm password|
Tools| Receiver info| Receiver| | Display info about
receiver
Hardware|
Software|
Remote control|
Game| Tetris|
Snake|
Othello|
Load factory default| |

Troubleshooting

Some simple checks or a minor adjustment may eliminate the problem and restore proper operation. Let a technician maintain the unit.
Keep the device away from static electricity during maintenance as the video processor is very sensitive.

Trouble Possible Cause Suggested Solution
No power Power cord has not been connected properly Plug the power cord

tightly into the power outlet and switch on the power. If there still is no power, switch off the unit again and wait 5 to 10 min. before switching the unit on
Can not scan program| •Antenna is not adjusted properly
•Parameter input is incorrect
•Use the antenna correctly| •Adjust the antenna or use an outdoor antenna
•Use an antenna with a 750 impedance
•Set the frequency and bandwidth correctly
No picture| •Output cord incorrectly connected
•Video output mode of the unit is set differently than the mode of the monitor| •Connect the output cord correctly
•Reset the working mode
No colour| •Output cord incorrectly connected
•Video output mode of the unit is set differently than the mode of the monitor| •Connect the output cord correctly
•Reset the working system
Image distortion from one channel to another| Normal|
The RCU is not working| •Batteries incorrectly inserted
•Batteries are exhausted
•Operation distance is too far or
operating angle is too large
•Remote control sensor is obstructed by bright light| •Insert the batteries correctly
•Replace the batteries
•Operate within the range
•Place the unit in another place
Audio sound and subtitle cannot be chosen| Sound channel incorrectly chosen| Press the AUDIO button to shift the channel
No sound| •Mute button is pressed
•Volume is set at a low level
•Cable incorrectly connected| •Cancel the mute
•Augment the volume
•Connect the cable correctly
Sudden sound drop| •Short circuit
•Mute button is pressed
•Entering sleeping status| •Connect the output cable correctly and reopen the unit
•Cancel the mute
•Reopen the unit
Seriously distorted reception| Serious interferential status| Adjust the antenna

Technical Specifications

Tuner

Input Frequency Range 174 ~ 230MHz; 470 ~ 862MHz
IF Bandwidth 7 or 8MHz
Input Signal Level -72 ~ -20dBm
RF Input Connector IEC169-2 type, female
RF Output Connector IEC type, male
Input Impedance 75Ω

Demodulation Mode

Waveform COFDM (Code Orthogonal Frequency Division Multiplexing)
Demodulation QPSK, QAM16, QAM64
Mode Mode 2K, 8K
Guard Interval 1/4, 1/8, 1/16, 1/32
Code Rate 1/2, 2/3, 3/4, 5/6, 7/8

Video, Audio Decoding

Video Decode ISO/IEC13818-2 MPEG2 compatible
Video Resolution 720 x 576 (PAL) or 720 x 480 (NTSC)
Video Code Rate max. 15M bits/s
Teletext support DVB-TXTETSI/EN300472
Audio Decode ISO 11172-3
Audio Track stereo, left ch, right ch
Audio Sample Rate 32, 44.1, 48kHz

HDMI™ Interface

Compliance HDMI™ 1.1 standard
HD Video Mode 480p, 576p

DVB® is a registered trademark of the DVB Project.
Use this device with original accessories only. Velleman nv cannot be held responsible in the event of damage or injury resulted from (incorrect) use of this device. For more  info concerning this product, please visit our website www.velleman.eu. The information in this manual is subject to change without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals